-
product
Low Power Programmable AC Source
Chroma Systems Solutions, Inc.
Delivers pure, instrument grade AC power at very low cost with output voltage from 0 to 300VAC, and frequencies from 15 to 1000Hz
-
product
Linear Bench or Rack Mount Power Supplies Programmable, Local Control, Ultra Low Ripple/Noise
Series PTR
SERIES PTR are operationally programmable power modules that can be programmed to any level within their rated range and fully loaded at any output setting. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Bus Analyzer, Exerciser, Emulator, and Programmer
CAS-1000-I2C/E
While the I²C interface seems simple on the surface, this straightforward architecture is not immune to intermittent glitches, device misbehaviors, and protocol violations. Likewise, tracking down these errors can be tedious business if the right tool is not utilized.The CAS-1000-I2C/E bus analyzer is an exceptional tool for pinpointing I2c irregularities. The ability to spot complex problems and identify invisible obstacles make it the preferred I²C development solution. Advanced logging, debugging, emulation, and verification capabilities offer power and versatility, yet the Windows-based user interface makes the most complex features simple to use.The CAS-1000-I2C/E succeeds where simple monitoring and interactive I/O tools fall short—a complete solution to monitoring, emulating, stressing, and characterizing I²C and SMBus interfaces.
-
product
Anti-Sulfurated High Power Wide Terminal Chip Resistors
Panasonic Industrial Devices Sales Company of America
An AEC-Q200 Compliant SeriesPanasonic components specified as AEC-Q200 Compliant are consistently designed into automotive systems. However, today’s Design Engineers are specifying AEC-Q200 components to meet the high-quality standards of devices beyond automotive applications.
-
product
Programmable Low-Ohm Meter
DU5210/5211
Delta United Instrument Co., Ltd.
20m ~ 2Mtest range, 0.1% accuracy Provided Level and Pulse measurement modes, can be lower temperature influence in Pulse Mode Provided HI/LOW limit and BIN Sorting comparator function, to meet your needed 100 sets of memory, can be saved test parameter and comparator setting, easy to use. Auto Calibration Program Function, to easier your calibration procedure. (Specificity calibrator needed) Cover up free, system firmware upgrade can be update via RS-232, easy to maintenance High speed FADC, max. test speed up to 80 meas./sec, faster your automation equipment 240*64 Graphic LCD display, can be read the reading clearly and easier. User friendly programmable interface, easy to use Provided RS-232C and Handler combinatorial interface option, to meet your needed
-
product
Linear Bench or Rack Mount Power Supplies Programmable, Local Control, Ultra Low Ripple/Noise
Series PAT
SERIES PAT are operationally programmable power modules that can be programmed to any level within their rated range and fully loaded at any output setting. These power supplies offer ultra low noise and ultra low ripple at the output and are MIL-STD-461 compliant.
-
product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2710
The 72-2710 from Tenma is a single channel programmable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
Boundary Scan Tester and Programmer
JTAGMaster
The JTAGMaster Tester and Programmer is designed to work with ABI's bespoke software - a multiple purpose platform which enables users to freely configure test procedures and instruments. Integrated functions are also available to the user to automatically learn the device status, provide pin-to-pin comparison and information as well as use some reporting facilities.
-
product
High Performance Programmable AC Power Supply
IT7600 Series
IT7600series high performance programmable AC power supplies, adopt advanced digital signal processing technology, with frequency up to 10-5000 Hz, built-inall-round power meter and large-screen oscilloscope function. Power up to 54kVA and support master-slave parallel, which can provide high-capacity single-phase or three-phase AC output.
-
product
Programmable AC Laboratory Power Supplies Linear
Programmable AC Laboratory Power Supplies Linear
-
product
Programmable High Precision DC Power Supply 1 Output 0-100V, 0-1A, 100W
T3PS100011P
Programmable High Precision DC Power Supply 1 Output 0-100V, 0-1A, 100W.
-
product
Digital TTL Control Modules - Programmable Module Accessories
Digital TTL Control Modules - Programmable Module Accessories by Pasternack
-
product
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A
T3PS30063P
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A.
-
-
product
Programmable Step Attenuator, DC to 50 GHz, 0 to 65 dB, 5 dB steps
84908M
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
product
6, 8 GHz, 4 Channel Programmable Attentuator
QPA8, PA8
This device has low impedance mismatch, high bandwidth, wide dynamic range and is capable of rapid state change. The QPA8 can be an attractive alternative to either the manually operated microwave attenuator switches, which are expensive and are switched very slowly, or the relay attenuators which are expensive and wear out quickly. Attenuation is controlled in standard steps of 0.0625 dB. The 10 bit programmable range results in the full 210=1024 steps yielding a dynamic range of 0 to 63.9375dB. Non-standard custom step sizes are available.
-
product
Programmable Delay Modules Instrument
The XS Series
Our XS series utilizes solid-state PIN diode technology to give you the fastest switching speed
-
product
Chip Resistor Networks
Panasonic Industrial Devices Sales Company of America
Chip Resistor Networks by Panasonic
-
product
10 Gb/s Programmable Digital Delay Line
PDDL10
The PDDL10 is a precision time delay generator for digital signals. Delays are controlled precisely in 5 increments from 0 to 635 ps.. Data rates through 10 gigabits per second are supported for very high-speed applications. Delays can be programmed via a TTL bus.
-
product
Programmable Limit Switches & Industrial Controls
Computer Conversions Corporation
Programmable Scale Factor16 High Current OutputsResolution to 1 in 4096Full Scale Zero OffsetNon-Volatile setpoint and Parameter Storage(EEPROM)Programs through zeroDigital Display of PositionTachometer (R.P.M.) DisplayResolver Connect DetectionRS 232 Program loading (option)300 Maximum program Setpoints with any Distribution over the 16 Outputs (1200 Optionally Available)Response time less than 5.1 microseconds
-
product
Chip Resistor Networks/Arrays
Panasonic Industrial Devices Sales Company of America
Panasonic’s Chip Resistor Arrays are offered in cases from 0201 to 0805. The smaller 0201 case sizes are available with flat terminations and all other case sizes are offered with either convex or concave terminations. The EXB Series Resistor Arrays are available in 2, 4, or 8 Resistors per package. These Resistor Arrays allow for an improvement of the placement efficiency. Compliance Standards include: IEC 60115-9, JIS C 5201-9, EIAJ RC-2129, AEC-Q200 and RoHS.Panasonic’s Resistor Networks are available in 8 or 15 bussed Resistors and are recommended for all pull up/down circuits.
-
product
Electromechanical Programmable Attenuators
BroadWave manufactures single section 6 dB to 8 section 0 – 127 dB programmable attenuators. •Voltage control and external TTL control •RF Connectors: BNC, N, SMA and TNC •50 and 75 Ohm
-
product
Programmable AC&DC Power Supply Unit
PADS
The energy feedback type programmable AC/DC power source with energy feedback unit equipped functions of voltage adjustable, frequency adjustable, harmonic controllable, low voltage ride through simulation etc.
-
product
PXI Programmable Step Attenuator Module, DC to 50 GHz
M9168E
The M9168E is a programmable step attenuator module based on PXI hybrid platform. The M9168E operates from DC to 50 GHz with a guaranteed 0.03 dB insertion loss repeatability for each section throughout the 5 million cycles operating life. Superior attenuation accuracy across a wide operating temperature range ensures precise measurements.
-
product
Programmable High Precision DC Power Supply 1 Output, 0-36V, 0-3A/,108W
T3PS36031P
Programmable High Precision DC Power Supply 1 Output, 0-36V, 0-3A/,108W.
-
product
4G Concurrent Device Programmer for PC /USB (4 sockets)
ProMax 4G
ProMax is the most innovative and cost effective 4- or 8-gang programming solution on the market. ProMax supports a wide variety of programmable devices. Its state-of-the-art technology and high-speed programming algorithms optimize throughput, reliability and yields.
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, LL/S , Programmable Amplitude Balance
LS-16A-R1-24SLS
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
Passive and Active Resistor Trimming for Thick and Thin Film
LRT 2000L
*Travel: 6" x 6"*Laser : Fiber Laser Ytterbium 1064 nm*Kerf: 30 to 80 micron Adjustable*Pulse width : 80 nano second*Rap Rate: 1 to 1 million Pulse Per Second*Average Power: 20 watts*Target: Electric crosshair on monitor
-
product
In-System Programmers
Xeltek in-system programming tools provide a convenient method for configuring microcontrollers and various serial devices. Users could simply program microcontrollers, Flash memories, PLDs, and FPGAs via the ISP cable. Devices are programmed in the target system or target hardware, making field applications more convenient than ever. Typically, a jumper/DIP switch enables in-system programming and a set of serial programming connector (such as an IDC connector) connects the target board(s) to the ISP programmer(s).
-
product
Programmable Electronic Load
Shenzhen UYIGAO Electronic Technology Co., Ltd
UYIGAO DC electronic loads provide you with the flexibility to test a wide range of power sources. Perform both static and dynamic tests to ensure that your devices can handle the steady state and occasional transient loads. The 16-bit voltage, current, and power-measurement systems provide accuracy analysis.
