-
-
product
Electronic Loads
PeakTech Prüf- und Messtechnik GmbH
Can be used for important test procedures in quality assurance as well as e.g. testing of power supplies and control units, batteries, fuel and solar cells. For precise load control for various purposes, this device offers load control according to constant voltage (CV), constant current (CC), constant load resistance (CR) or constant power (CP) with a highly precise resolution of 1mW, 1mV, 1mΩ and 1mA. The device also offers additional test modes, e.g. the battery test or the dynamic test. The PC interface and software offer the option of implementing freely programmable test sequences with data evaluation.
-
product
RF Spectrum Analyzer
FSA-100
ShinewayTech® FSA-100 series 6GHz spectrum analyzer are widely used in 2G/3G/4G/5G etc. FSA-100 series have the industry's rare high receiver sensitivity performance with a minimum display average noise level of -165dBm/Hz. Power measurement dynamic range up to 100dB, maximum RF input power exceeds 27dBm. FSA-100 series are equipped with a 7" ultra-large capacitive touch screen (resolution 1024*600). Excellent user experience.
-
product
Canister Load Cell
Futek Advanced Sensor Technology, Inc.
FUTEK provides a wide range of Canister Load Cells designed for high capacity compression applications. These models offer robust construction with a capacity range beginning
-
product
AC Load Banks
X100L Series
Mosebach Manufacturing Company
Introducing Mosebach’s X100L load bank. One of the lightest dual voltage, 100 kW load banks on the market! The unit weighs approximately 64 lbs. and has 5 kW resolution. The X100L load bank includes an Industrial strength, injection molded, 100% water proof case with wheels as shown below.
-
product
RF Spectrum Analyzer
RF-EXPLORER / 3
Monacor International GmbH & Co.
RF Spectrum Analyzer, 15-2700MHz, in a compact aluminum housing with two antennas (SMA connection) for the different frequency ranges, among other things to avoid frequency collisions when setting up radio links in the frequency range mentioned above
-
product
Load Banks
EL08 Series
*Rectifier Test 8kW*All of our Load Banks are continuously rated for Power and Current.
-
product
Compression Load Cells
A block that is designed to hold a load at one point to measure the compression. While tension load cells measure the pulling force, compression load cells measure a pushing force along a single axis.
-
product
Small Telemetry Compressive Load Cell
TC-3.0-SM
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.
-
product
RF Switch Assemblies
We can package any of our solid-state or electro-mechanical RF switches into a remotely controlled RF switch assembly. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
-
product
Load Cell Indicator
Morehouse Instrument Company Inc.
This indicator can read mV/V and use free, custom Morehouse software to convert the mV/V units to engineering units with coefficient files from ASTM E74 or ISO 376 reports. This meter is often the choice for accredited calibration service providers that want high accuracy and convenience but do not want to break the bank.
-
product
RF Planing & Optimization Software
Atoll
Atoll is a scalable and flexible multi-technology network design and optimisation platform that supports wireless operators throughout the network lifecycle, from initial design to densification and optimisation. Supports: GSM / GPRS / EDGE, UMTS / HSPA, CDMA2000 1xRTT/EV-DO, LTE, TD-SCDMA, WiMAX / BWA, Microwave links.
-
product
RF And Microwave Accessory Kit
N9311X
N9311X RF and Microwave Accessory Kit complements Keysight's low-cost handheld and benchtop solutions. These accessories provide you with a complete solution when using Keysight handheld and low-cost benchtop solutions for your measurement needs.
-
product
RF Frontends
Becker Nachrichtentechnik GmbH
Software-Defined Radio (SDR) is an attractive approach for mobile communication architectures in the development and evaluation phase for a rapid prototyping on a flexible platform. SDRs support a wide frequency range. However, for practical use in the field the HF properties are insufficient. The transmit power is limited to a 2-digit mW value. Dedicated filters are required for an effective suppression of out-of-band signals and to improve the noise figure of the receiver chain. Extending SDRs with application-specific RF-frontends achieves optimal RF performance in the field.
-
product
Bluetooth RF Test System
FRVS
FRVS is recognized by the Bluetooth SIG as a validated test system for qualification testing of products to Bluetooth BR/EDR and low energy RF test specifications.
-
product
RF Microwave Switch Matrices
RF Microwave Switch Matrices provide automatic routing of RF microwave signals between test instrumentation and the unit under test (UUT). They provide consistent signal paths, enable automation of tests, and often include signal conditioning.
-
product
Load Cells
Whether you need general purpose, low profile or miniature cells for standard or special applications, you don't have to be an expert in force measurement, because we are. Talk to us about what sort of forces you need to measure, and under what conditions and constraints. We'll walk you through the load cell specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
product
AC Load Banks
XL300-400 Series
Mosebach Manufacturing Company
The XL300-400 Series of Load Banks offer 300 kW or 400 kW in various voltages in a compact, lightweight enclosure.
-
product
DC Electronic Load
M9822/M9822B
M9822/M9822B is newly designed circuit adopts rapid AD and DA technology to achieve rapid measurements with high accuracy. And the resolution of 0.1mV/0.1mA can effectively display the minor change of voltage and current, so the instrument has a wider application field and achieves better test results. Meanwhile your operation becomes much more comfortable and easy by equipping the high-light VFD, the simple menu and displayed contents and the operation state indicators on all keys. Otherwise the complete and humanized test functions will greatly improve your productivity.
-
product
1800~3000W DC Electronic Loads
JT633 series
Nanjing Jartul Electronic Co., Ltd
JT633 series electronic load is functioned with 500KHz high-speed synchronous sampling, DSP technology, powerful dynamic test and multi-aspect intelligence analysis. All these are fully integrated into auotmatic test function, which makes JT633 series load very suitable for testing power supply when produced in large quantity. Besides, JT633 series load also possesses the features of current rising slew rate programmable, high-speed dynamic loading and programmable list function, which makes JT633 series load satisfing most of R&D requirements.
-
product
RF Front-End ICs
Analog Devices offers RF Front-End ICs for phased array antenna solutions. These RF Front-End ICsare placed right at the antenna element and can quickly switch between transmit and receive functions in radar applications. The power amplifier on the transmit side is highly efficient operating in short pulse durations. The low noise amplifier on the receive side has a low noise figure with high linearity so that it won’t distort the incoming return signal. The RF Front-End IC also incorporates a high performance switch to toggle between the transmit and receive paths. Highly integrated planar phased array antennae need small form factor solutions, and Analog Devices has integrated the switch, low noise amplifier, and power amplifier into a small surface mount package as well as the decoupling capacitors, providing an optimal solution.
-
product
RF Filters
Smiths Interconnect is committed to providing technically advanced, high quality “state-of-the-art” RF Filters, Multiplexers, Switched Filter Banks, and Integrated assemblies, from 100 KHz to 65 GHz. All products are subject to the same rigorous design, manufacturing, and inspection criteria. Regardless of the application, our internal process and procedures help ensure that all products are fully compliant to all specifications. Our R & D activities are constantly evaluating new materials, plating techniques, and manufacturing processes to offer the highest performing components available today.
-
product
300 Watt Electronic Load Module
N3304A
The Keysight N3304A is a 300 W (0-60A, 0-60V)electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3304A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3304A can also digitize waveforms.
-
product
High Power DC Electronic Load
33500F Series（2.4KW~14.4KW）
33500F Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store/Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface. SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
RF Calibration Accessories
Employing good connector practice when using an RF calibrator not only avoids measurement errors and minimizes connector repeatability uncertainties but also reduces risk of damage to connectors and equipment. The 96000CONN and 9600CONN connector kits include a range of adapters and torque wrenches intended for use with the 96000 Series RF Reference Sources (9600CONN for the 96040A and 96000CONN for the 96270).The 9600CONN connector kit includes one each of 50 Ω and 75 N-Type male-female adapter for use with the 96000 Series levelling head as a “connector saver” or “sacrificial connector” to avoid risk of damage when making connections to UUT/DUT instruments.
-
product
RF Connectors
MCX Connectors
The MCX (Micro Coaxial) series is available with 50 or 75 ohm options, and has broadband capability ranging from DC to 12 GHz. In addition, the MCX series features secure, fast and easy snap-on/ snap-off coupling. MCX connectors were introduced in the 1980s and conform to the European CECC 22220 spec.
-
product
RF Downconverters
SignalCore offers traditional multi-stage and single-stage RF downconverters, and Direct IQ demodulators that feature low phase noise, high dynamic range, wide bandwidth, and continuous tuning. SignalCore RF downconverters are compact and built for mechanical robustness and ruggedness. Applications include various test and measurement applications such as those in spectral monitoring, signal intelligence, ATE, and software-defined radio. All products are provided with a Graphical User Interface (GUI), driver, and API for easy programming control.
-
-
product
Load Cell Amplifier
Xiamen Elane Electronics Company, Ltd
: 0-50 degrees. Humidity: 30 to 80 percent, non-condensing.Power Supply Requirements:Power Supply voltage: 9 volts DC.Operating current: 5mA, plus bridge current.Bridge Input:Excitation voltage: 5 volts.Bridge Type: Full Wheatstone Bridge.Voltage Output Range: From 0 volts to 4.3 volts.
-
product
Load Cell Transmitter
MODEL SST-HV
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
