DC Current Sources
-
Product
Mercury Argon Calibration Source
HG-1
-
The compact, low-cost HG-1 Mercury Argon Calibration Source is a spectral wavelength calibration source for UV-VIS-Shortwave NIR spectrophotometric systems.
-
Product
3 Phase Flexible AC Current Probe
DRP 503/18
-
The new DRP 503/18 is a 3 Phase Flexible AC current Probe utilising the Rogowski principle, with 3 channel integrator housed in DIN Rail Mounted Enclosure. The flexible and lightweight measuring head allows quick and easy installation in hard to reach areas and with large conductors.
-
Product
Current Transformer
-
Nippen Electrical Instruments Co.
DIGITAL METERS NIPPEN electronic energy meters are panel mounting type innovative energy monitoring devices ,having state of the art electronic microcontroller circuitry for reliability and accuracy. They can be used for 1Ø / 3Ø balanced and unbalanced loads.
-
Product
Scienlab Dynamic DC Emulator
SL104XA Series
-
The Scienlab Dynamic DC Emulator provides an all-in-one system for efficient and effective testing of the power electronic components in electric vehicles (EV) and electric vehicle supply equipment (EVSE).
-
Product
Optical Light Sources
-
Wuhan Sunma Technology Co., Ltd.
Fiber Optic Light Sources are a necessity for performing fiber optic network testing to measure the fiber optical loss for both single mode fiber cable and multimode fiber cables. They are designed to cover a variety of wavelength ranges to suit all optical testing needs and usually the optical light sources are used with the fiber optic power meter to test the fiber system loss. Light sources are offered in a variety of types including LED, halogen and laser. Usually the optical light source is used with the fiber optic power meters, they act as an economic and efficient solution for the fiber optic network works. SunmaFiber offers handheld fiber optical light source and laser light source.
-
Product
AdvancedTCA, Type 11A, 2U 19" Horizontal, DC
11A02FJB28Y3HMXX
-
Elma's ATCA, DC, 2U horizontal enclosure with backplane, and shelf mgmt. options. Pluggable and redundant fan trays, PEMs and shelf managers for availability (99.999%). Optimized via backplane signal integrity studies and chassis thermal simulation.
-
Product
LED Test Programmable DC Electronic Load
IT8912E Series
-
IT8900 series high accuracy LED specific testing electronic loads can simulate the real output of LED lights with different characteristics.Their specific circuit can realize CR-LED mode, adjustable frequency, duty ratio PWM dimming output port (frequency: 20Hz-2KHz), I-pp/I-max measurement function can test current ripple and start up surge current of LED constant flow source. Voltage and current testing speed can reach 50KHz. IT8900 series provides CR-LED / CC / CV + CC / CR /CW and other working modes, built-in USB / RS232 / GPIB communication interface. Widely used in LED driver power dimming test.
-
Product
Power Divider, DC to 26.5 GHz
11636B
-
The Keysight 11636B is a dc to 26.5 GHz power divider for direct power dividing applications. The excellent impedance match of all three ports improves fault location measurements by reducing re-reflections. The Keysight 11636B power divider/combiner is recommended when making wideband comparison measurements with the Keysight 8757 scalar vector network analyzer.
-
Product
Ultra Low Noise DC Power Supplies
R4G Series
-
R4G series are series regulator system DC power supplies so that enabled setting and reading out more fine output with a 4-digit indicator on furont panel and a high resolution D/A and A/D converter adopted newly.
-
Product
C+L Band Broadband Light Source
S-103
-
ASE broadband source slot module of FOTS system can offer special function that is able to change optical output spectral feature variously, which is change optical output spectral feature variously, which is followed by user’s driving embedded pump LD freely. The output power of each pump LD is controlled separately by the program that is set up by user. In the case optimum ASE source output features such as wide broadband (> 80 nm @ -10 dBm/nm) and stable output power (< 0.02 dB) is needed, it is made up so that the provided Default mode along with User mode can be chosen and set up. More stable application of ASE source is possible through the combination of monitoring of ASE output power, alarm status and pump LD status with real-time optimal feedback. The embedded FPGA processor makes high speed control possible and enables monitoring and feedback routine operated stably.
-
Product
High Frequency Digital Surge Tester & DC Hi-Pot Tester
SPM
-
High Frequency Digital Surge Tester and DC Hi-Pot Tester (similar to the "SP" Model) together in a compact cabinet. Take this portable tester to your test site and accurately perform Surge, Hi-Pot, PI and Resistance Tests.
-
Product
Tunable System Sources
-
The Keysight N7711A and N7714A tunable lasers are single-port and four-port sources, available with C-band or L-band wavelength coverage. All models can reach any wavelength point within their specified wavelength in the C- and L-band range. The narrow linewidth and offset grid fine-tuning capability make them ideal sources for realistic loading of the latest transmission systems. In system loading applications, it may be preferable to grid-tune the lasers like system transmitters, simply by changing the channel index. The channel grid is adjustable to standard ITU-T grid spacing like 50 GHz, and to arbitrary grids. The Keysight N7711A and N7714A tunable lasers are available in a compact format with half-rack width and one rack-unit height. This format makes them the right choice for high channel-count system load applications.
-
Product
DC Electronic Load, Single-Input: 150V, 40A, 250W
EL33133A
-
The Keysight EL33133A bench DC electronic load provides a single input and a built-in data logger. Provide static or dynamic load test up to 40 A and 150 V. Display results in a meter view or over time using the built-in data logger.
-
Product
DC to 1GHz
1396A
-
Dimensions: 6.4 cm (2-1/2") diam. x 11.6 cm (4-5/8") long, except 10.5 cm (4-18") for 7 V rating. Weight: 1.1 kg (2 lbs 4 oz)
-
Product
Current Transformer Tester
CTT
-
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Product
Excitation Sources
-
SPECS Surface Nano Analysis GmbH
o our customers in research and industry we offer a variety of sources for deposition, excitation and charge neutralization as well as analyzers and monochromators. Most of our sources originate from product lines which we have taken over from Leybold AG, Cologne, and from VSI GmbH. The X-ray monochromator Focus 500 and the UV monochromator TMM 302 are original developments by SPECS.
-
Product
Rogowski Coil Current ProbesTOP
-
*Switching current waveform and pulse response characteristics of power devices*Current measurements of inverter system*AC current measurements (at large DC offset)*Impulse high current measurements*Bus Bar high current measurements
-
Product
C Series Current Output Module
Input/Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Primary Current Injection Testers
-
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
Product
Zero Phase Current Transformer
MZL-30
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
Split-core type for measuring zero phase current
-
Product
DC Electronic Loads
LSG Series
-
*Operating Mode : C.V/C.C/C.R/C.P/C.C +C.V/C.R + C.V/C.P. + C.C.*High Precision, High Resolution (10 A),High Speed Variable Slew Rate (16A/ s).*Sequence Function for High Efficient Load Simulations.*Parallel Connection of Inputs for Higher Capacity. (With 4 Booster Units : Max 9.45kW or 4 Master Units)*External Channel Control/Monitoring via Analog Control Connector.*Program Mode to Create Work Routines for Repetitive Tests.*Multiple-Interface : USB 2.0 Device/Host and GPIB/RS-232C.*Adjustable OPP/OCP/OVP Setting.
-
Product
DC Isolating Transmitter
Model TW2D
-
Kusam Electrical Industries Limited
• 2 Inputs / 2 Outputs User Selectable• High Accuracy 0.1% RO at 23 °C ± 5 °C• Aux. Power AC 85 ~ 265V or DC 85 ~ 300V• PC Plastic Case, DIN Rail or Wall Mounting• High Dielectric Strength (AC 2KV/ Min, between Input/Output/Power)
-
Product
Solid State Flasher, DC Input
A738
Solid State Flasher
NAI’s A738 is a 2.5 A, DC Input, Aircraft Warning or Position Light Flasher. This solid-state, single-channel unit is designed for airborne use and performs to all applicable military specifications.
-
Product
Current Transformers
Sensors
-
The Current Transformer (CT) is the sensor which measures the amount of current draw from the wire it is installed on.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Sound Power Reference Source
Qref
-
Precision omni-directionallity in all directions, horizontal and vertical plane. This source has a frequency range of application between 100 and 8000 Hz (third octave bands) Despite only weighing 1.4 kg and having a diameter of 105 mm, it produces a maximum sound power level of Lw 104 dB.
-
Product
Current Injection Sets
-
Built in c based Time Interval Meter measuring from1 millisec to 9999 sec. Panel with easy and clear legends to read. Continuosly variable outputs. Auto Cut-off & output isolated. Self sensing of contacts i.e. NO or NC Potential free star stop signals Available in Portable / Lab type models with metal cover
-
Product
DC Blocking Power Splitter Combiner
PD5120
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.2 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) 50 Ohm
-
Product
2000-6000W AC power source
CX-P2KW
-
Shenzhen Chuangxin Instruments Co., Ltd.
The AC power source is made by adopting microcomputer processing chip and high power device. It provides a stable pure sine wave and has voltage, over current, over temperature, overload protection. It can output 0-300V adjustable voltage, and 45-70Hz adjustable frequency as well as fixed frequency as 50 Hz or 60 Hz, 100 Hz and 200 Hz and 400 Hz. This AC power source can simulate power grid of different countries, provide a stable voltage, frequency, waveform which can be used to test and age the exprot products and provide kinds of precision tests for laboratory, measuring room, etc.
-
Product
Current Measurements Of PWM Or Inverter, AC/DC 10～200A, Φ24mm
CTF-200DC-U48V
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*AC/DC 10～200A*Current measurements for PWM or inverter
