Software
a set of instructions to run hardware and or process data.
-
Product
*PC Interfaces
-
Ophir PC interfaces work on the smart plug principle. This means that almost any Ophir PC interface can work – plug and play – with almost any of the wide range of Ophir sensors. Ophir PC interfaces are also the most precisely calibrated units on the marketת, thus measuring with the highest accuracy. With the versatile Ophir StarLab software, your PC becomes a complete laser measurement station. Ophir also provides software to interface seamlessly with LabVIEW or the user's own software.
-
Product
Battery Data Logger
BDL-3927
-
Kongter Test & Measurement Co., Limited
BDL-3927 is updated Battery Data Logger to meet IEEE measurement standards for battery voltage, string voltage, current and ambient temperature. It is customized from 12V to 700V for different battery systems. And it has easy expansion for all battery systems. With wifi communication, you could easily view complete data and generate test report in the PC software.
-
Product
High Frequency Antenna Analysis Software
XGtd®
-
XGtd is a general purpose ray-based electromagnetic analysis tool for assessing the effects of a vehicle or vessel on antenna radiation, predicting coupling between antennas, and predicting radar cross section (RCS). It is ideally suited for applications with higher frequencies or very large platforms where the requirements of a full physics method may exceed available computational resources.
-
Product
USB Interface
PK-232/USB
-
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Product
170MHz 4-Channel DDS Signal Generator
409B
-
The 409B generates four independent, phase synchronous sine wave output signals and is programmable in 0.1 Hz steps from 0.1 Hz to 171 MHz. Programming is via an RS232 serial interface. Phase is 14-bit programmable and amplitude is 10-bit programmable. Internal memory can store a sequence of settings. The -AC option is available to enable users to step through settings using an external trigger. It is accurate to 1.5 ppm using the on board TCXO timebase or you can use an external timebase, There is also a /R option that provides a way to lock to and track an external 10MHz frequency input. A line powered AC adapter and SOF8_409 windows software on a CD are included.
-
Product
MXG X-Series RF Vector Signal Generator, 9 kHz to 6 GHz
N5182B
Vector Signal Generator
Take your designs to their limit with outstanding hardware performance, including unmatched phase noise & spurious characteristicsDrive power amplifiers & characterize nonlinear behavior with industry-leading ACPR & output powerTest wideband devices with factory-equalized 160 MHz RF bandwidthReduce the time spent on signal creation with Signal Studio software, including LTE, WLAN & GNSSLower your cost of ownership with 3-year cal cycles & comprehensive solutions for self-maintenance
-
Product
PCIe Fast Multifunction, Multichannel Counter Board, Optically Isolated, RS-422 Inputs
APCIE-1711-5V-I
-
The APCIe-1711 board is a fast multifunction and multichannel counter board for the PCI Express bus. The strengths of this board are its wide range of applications and high precision and reliability for industrial applications. With this board you can realise many different applications on the same hardware base. The board is supplied with a pool of functions which provide the user with maximum efficiency yet minimum space and parts requirement. The functions are individually configured for each channel through the supplied software. The flexible programming facilities on this board allow many differentuser applications to be quickly and easily developed and reconfigured as further requirements arise. Thanks to the FPGA board structure, further counting applications canbe realised through software adaptation.
-
Product
High Resolution Fiber Grating Sensor Interrogation System
GM8037
-
UC INSTRUMENTS’ GM8037 portable high resolution fiber grating sensor instrument is ahigh power with high accuracy and wide dynamic range for fiber Bragg grating (FBG)sensors, and compact PC-based interrogation system, and is also a high accurate opticalspectral analysis system. It includes an external device, PC-based application software andoptional high performance laptop.
-
Product
Video Generator-Analyzer
VQTS-200
-
VQTS-200 is a self-contained solution, combining: 3G-SDI/HDMI/DVI player/recorder - based on AJA Kona LHi card Built-in RAID storage - uncompressed YUV signals in and out, up to 1080p60 Visual, instrumental and automated tests using VQL Test Patterns Library Sophisticated image quality VQMA3 software analyzer - complete quality report in 2 seconds Ideal tool for development labs, software developers and high volume manufacturers Easy-to-use tool, instantly revealing your video camera, codec, scaler, converter or other video device performance User-selectable reporting modes: machine-readable file with Pass/Fail marks detailed multi-page PDF document
-
Product
Camera Test System
FS 8681 / SR
-
FS8681/SR is software for evaluating images* and making pass/fail judgments in camera mass production inspections. It consists of the "Editor FS8681" application that sets the inspection content and the "Sequence Runner FS8681SR" application that executes the set inspection.
-
Product
OCD Solutions
-
Onto Innovation’s OCD technology offers powerful OCD modeling and advanced machine learning capability, as well as next-generation real-time regression, offline sensitivity analysis tools and comprehensive GUI and structure input for true multi-variant modeling. Both the Ai Diffract and SpectraProbe software packages deliver advanced capabilities in intuitive and easy to deploy hardware form factors.
-
Product
Hand-helds
-
Hand-helds are portable calibration instruments for mobile use for the accurate measurement and recording of temperature profiles. For the instruments there are various designs of thermometers available. Through this, hand-helds are particularly suitable as test instruments for a large variety of applications in the widest range of industries. Data recorded in the hand-held can be evaluated via PC software, some instruments document calibrations in the internal memory, which can later be read on a PC. Optionally, a calibration certificate can be generated with our calibration software WIKA-Cal.
-
Product
Software
Customized Software
-
Materials Development Corporation
If the software packages offered do not meet your specific needs,special software can be written for custom applications.The engineers and programmers at MDC candevelop or modify applications to fit your requirements. Examples include: *Customer specific measurements *Interfacing with required meters *Production versions of measurements *Interfacing with probers and other measurement platforms *Specialized requirements
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781263-01
Signal Module
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
PXIe-5673E, 6.6 GHz PXI Vector Signal Generator
781340-03
Vector Signal Generator
6.6 GHz PXI Vector Signal Generator—The PXIe‑5673E is a wide-bandwidth module that, when combined with the appropriate software, can generate a variety of signals. With the Modulation Toolkit for LabVIEW, it can generate different waveforms including AM, FM, CPM, ASK, FSK, MSK, PSK, QAM (4‑, 16‑, 64‑, and 256‑QAM), multitone signals, arbitrary waveforms, and many others. In addition, you can combine these vector signal generators with standard-specific software to generate signals for GPS, GSM/ EDGE/WCDMA, WLAN, WiMAX, DVB‑C/H/C, ISDB‑T, ZigBee, and others. With PXIe‑5673E stream‑from‑disk capabilities, you can generate continuous waveforms that are up to several terabytes in length.
-
Product
Spectrum Analyzer / Measuring Receiver
USB-SA124B
-
The Signal Hound USB-SA124A is a Software Defined Radio (SDR) optimized as a spectrum analyzer. It is compact, simple to use, and an effective troubleshooting tool for general lab use, engineering students, ham radio enthusiasts, and electronics hobbyists. Using recent innovations in RF technology, the Signal Hound has the sensitivity, accuracy and dynamic range you''d expect in a unit many times its cost.
-
Product
Sophisticated Audio and Video Test Patterns
VQL
-
VQL Instantly reveals your video display, codec, scaler, converter or other video device performance VQL test patterns cover all 3 levels of video QA/QC: Instant visual-aural Quality Estimation Objective Measurements of video and audio performance Fully automated (unattended) Quality Control VQL features: Compatibility with all commonly used software or hardware codecs and media players VideoQ VQV / VQMA / VQTS / VQDM compatible tests Wide range of video frame sizes: from 192x108 to 4096x3072 Variety of bit rates up to uncompressed 4:4:4 4K @60 fps, 48 bit per pixel Variety of video and audio formats, color spaces and level schemes All test patterns remain suitable for accurate measurements even after low bitrate coding, heavy scaling and/or cropping, e.g. after down-conversion for mobile devices Standard, custom and semi-custom tests for development labs, content processing facilities, CDN systems, software developers and high volume manufacturers
-
Product
ONE BOX
-
Both the Z and X handheld analyzers run on the same software platform, operating system, have the same user interface, same battery, and same charger making training and operation a breeze. Get them both when you purchase the ONEBOX package.
-
Product
Gas Flow Standards
-
Fluke Calibration offers molbloc/molbox gas flow calibration systems to calibrate flow meters and controllers over a very wide range of flows. The systems are fast, precise and transportable and can be fully automated using COMPASS for Flow software. molblocs, which are the heart of the measurement system, are mechanically stable, gravimetrically calibrated laminar flow and sonic nozzle elements.
-
Product
Wireless Connectivity and IoT Test System
IQxel-M4W
-
Suitable for the lab or manufacturing environment, the IQxel-M4W 6G is ideal for RF testing of wireless connectivity and IoT products. The platform’s flexible software supports the most prevalent wireless connectivity standards: WLAN 802.11ax (Wi-Fi 6) and legacy (802.11a/b/g/n/ac), Bluetooth® Classic and Low Energy (Bluetooth® LE) as well as Zigbee/Thread, Z-Wave, LPWAN technologies (Sigfox, LoRa) and cellular IoT technologies (NB-IoT, LTE-M, 5G) as well as navigational technologies.
-
Product
AcroPack® I/O Modules
-
Acromag provides software support packages for embedded applications running on Linux®, Windows®, or VxWorks® operating systems. The libraries provide generic routines to handle reads, writes, interrupts, and other functions. Demonstration programs enable the developer to quickly exercise the I/O modules before attaching the routines to the application program. This diagnostic tool can save hours of troubleshooting and debugging.
-
Product
Coating Thickness Gauge
CM8855
-
It meets the standards of both ISO2178 and ISO 2361 as well as DIN, ASTMand BS. It can be used both in the laboratory and in harsh field conditions. The F probes measure the thickness of non-magnetic materials (e.g. paint,plastic, porcelain enamel, copper, zinc, aluminum , chrome etc.) on magneticmaterials (e.g. iron, nickel etc.) . often used to measure the thickness ofgalvanizing layer, lacquer layer,porcelain enamel layer, phosphidelayer, copper tile, aluminum tile, some alloy tile, paper etc. The N probes measure the thickness of non - magnetic coatings on non-magnetic metals .It is used on anodizing, varnish, paint, enamel,plastic coatings, powder, etc. appliedto aluminum, brass, non-magnetic stainless steel, etc. Automatic substrate recognition. Manual or automatic shut down. Two measurement mode: Single and Continuous Wide measuring range and high resolution. Metric/Imperial conversion. Digital backlit display gives exact reading with no guessing or errors. Can communicate with PC computer for statistics and printing by the optional cable. Can store 99 groups of measurements. Statistics is available.2.SPECIFICATIONSDisplay: 4 digits LCD, backlitRange: 0~1250 μm/0~50mil (other ranges can be specified )Min.radius workpiece: F: Convex 1.5mm/Concave 25mmN: Convex 3mm/ Concave 50mmMin. measuring area: 6mmMin.Sample thickness : 0.3mmResolution: 0.1 μm (0~99.9μm);1 μm (over 100μm)Accuracy: ±1~3%n or 2.5 μm or 0.1mil(Whichever is the greater)Bttery Indicator: Low batter indicator.PC interface: with RS-232C interfacePower supply: 2x1.5 AAA(UM-4) batteryOperating condition: Temp. 0~50℃ .Humidity <95% .Size: 126x65x35 mm; 5.0x2.6x1.6 inchWeight: about 81g(not including batteries)Standard accessories:Carrying case ...................1 pc.Operation manual ............ 1 pc.F probe in built .................1 pc.NF probe in built...............1 pc.Calibration foils ..............1set.Substrate (Iron) ................1 pc.Substrate (Aluminium)......1 pc.Optional accessories: RS-232C cable & software:1.USB adaptor for RS-232C2.Bluetooth interface
-
Product
Rebound Hammer
SilverSchmidt - PCL
-
Concrete test hammer SilverSchmidt Type PC L : *Impact energy (0.735 Nm) with PC communication, increased memory capacity and Hammerlink software*Use for concrete <10cm and fragile rocks*Measuring range: 10-100N/mm2
-
Product
75 Ohm Solutions
-
Vector Network Analyzer delivers lab grade performance in a compact package, with all the features engineers have come to expect included standard in our software.
-
Product
Semiconductor Test
Ismeca NY32
-
32-position turret platform for semiconductor test, inspection and packaging, providing the highest process integration capabilities. Integrating innovative hardware and software technology such as Intelligent Features that enables extended autonomous operation and productivity.
-
Product
GNSS Software Receiver
SX3
-
With IFEN’s SX3 frontend measurement synchronization betweenIF-sample data and external sensor data (as IMU or barometer for example) is possible,as well as integration of user defined algorithmswithin the SX3 application programming interface.
-
Product
Spectrometers and Spectroradiometers
ASD Range
-
ASD spectrometers and spectroradiometers provide state-of-the-art, real-time spectral performance. These instruments, when combined with ASD’s software and support tools create powerful information that helps you to improve, simplify, and streamline your research and production processes, ideal for a multitude of materials measurement solutions.
-
Product
Signal Architect Simulator Software
GNSS
-
The GNSS Signal Architect Simulator Software is ideal for applications requiring: High fidelity simulation of GNSS signals Digital data analysis of GNSS signal effects RF signal generation through digital playback Highly repetitive testing where consistency between test runs is critical Easy to use Graphical User Interface Low initial and support costs
-
Product
Enterprise Service Bus
Kovair Omnibus
-
Software teams are using multiple best of the breed tools but mostly they work in silos without real-time sharing of data.Now integrate those tools through Kovair Omnibus to achieve cross-team and cross-tool collaboration across disparate systems.Choose from the list of 70+ integration adapters or connectors developed by Kovair.
-
Product
Integration testing
-
Integration testing primarily focuses on verifying data communication among different modules of the software project. Integration tests determine the effectiveness and performance of different software modules when they are connected to each other.
