Load Cell Simulators
generate a precise mV/V signal to assure load cell amplifier, tester, readout and display set up.
See Also: Load Cell Test, Load Cells
-
Product
S-Type Load Cells
-
S-Type Load Cells take their name from their shape – as you can see from the images below – they are in the shape of the letter “S”. These load cells are commonly used in tension applications; mechanical-to-electrical scale conversions as well as weighing applications including cranes etc.
-
Product
Load Cell Amplifiers
-
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
Product
Load Cell Electronics
-
All our electronics are continuously evolving to feature faster and more powerful components. This commitment to innovation ensures that we can meet any new challenge or application.
-
Product
Small Telemetry Compressive Load Cell
TC-3.0-SM
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 32 Channel
41-761-001
Simulator
The 41-761-001 is a low voltage 32-channel output module ideal for simulating theoperation of a thermocouple, also available with 24, 16 or 8 channels. Each channel of the 41-761 provides a low voltage output across two connector pins capable of providing ±20mV with 0.7μV resolution, ±50mV with 1.7μV resolution and ±100mV with 3.3μV resolution, covering most thermocouple types.
-
Product
PXIe Battery Simulator Module, 4-Channel, 5 Amp
43-754-011
Battery Simulator
The 41-754-011 and 43-754-011 are 4 channel battery simulators, capable of supplying up to 8 V and 5 A per channel. The channels are fully isolated from ground and from each other allowing series connection to simulate batteries in a stacked architecture. The isolation barrier (1000 V channel to GND and 750 V channel to channel) allows the module to be used as a battery stack representative of those used for vehicle propulsion..
-
Product
Shear Beam Load Cell
SB-1.0
-
The Shear Beam Load Cell SB-1.0 is a single point weighing device, suitable for use in multiple applications.
-
Product
Pedal Force Load Cells
-
Pedal Effort Sensors are designed to measure load applied to the brake, accelerator, and clutch pedals during acceleration, deceleration, and transmission shift events. The units are compact and light weight, making them easy to install and remove.
-
Product
Advanced Diagnostic Load Cell Tester
LCT-U
-
The Advanced Diagnostic Load Cell Tester Model LCT-U is a stand-alone hand-held device specially designed for fast, comprehensive troubleshooting of strain gauge load cells. The LCT-U can quickly diagnose problems with all common types of load cell available today, including 6-wire load cells (with sense wires).
-
Product
Load Cell Power Supply Module
MODEL PSM-F10
-
The PSM-F10 is a chassis mountable power supply package. They are ideal for use with dedicated microprocessor systems, instrument design and test equipment. The PSM-F10 can also be used as a supplemental bench or laboratory power supply. The special "Cclamp" type barrier strip secures the wire without twisting. Note the protected recessed barrier strip facing the top of the case. This allows connections to be made in tight areas while protecting the barrier strip from physical damage. Nothing else offers this combination of ruggedness, flexibility and convenience.
-
Product
LED Load Simulator
63110A/ 63113A/63115A
Simulator
As shown on the V-I curve in figure 1, the LED has a forward voltage VF and a operating resistance (Rd). When using a resistor as loading, the V-I curve of the resistor is not able to simulate the V-I curve of the LED as shown in blue on figure 1. This may cause the LED driver to not start up due to the difference in V-I characteristic between the resistors and the LEDs. When using Electronic Loads, the CR and CV mode settings are set for when the LED is under stable operation and therefore, is unable to simulate turn on or PWM brightness control characteristics. This may cause the LED driver to function improperly or trigger it’s protection circuits. These testing requirements can be achieved when using a LEDs as a load; however, issues regarding the LED aging as well as different LED drivers may require different types of LEDs or a number of LEDs. This makes it inconvenient for mass production testing.
-
Product
Grid Simulators
Simulator
A grid simulator can be used to simulate the characteristics of low-voltage mains. For this purpose, all voltages and frequencies of the supply networks occurring worldwide can be simulated. Critical states such as short-term voltage dips or voltage peaks (surge/burst) can also be generated.The integrated sequencer function enables the generation of different network parameters, e.g. distorted waveforms and intermediate oscillations. Therefore, grid simulators are well suited for testing conformity to standards and especially for determining the behaviour of electrical equipment in borderline situations. Many European and other international standards are pre-programmed for testing.
-
Product
S-Beam Static Load Cells
2519 Series
-
The 2519-xxxN Series load cells are specifically designed for use with 3300 single column testing systems. Automatic transducer recognition and electrical calibration makes them easy to use. The load cells incorporate overload protection and can withstand loads up to 150% of their force capacity without damage and 300% without mechanical failure. The load cells allow the user to zero out the tare weight of a grip or fixture that weighs up to 40% of the force capacity, while still maintaining the full specified accuracy.
-
Product
Press Force Load Cell
6000 Series
-
Press Force Load Cells are strain gage based transducers for press-force monitoring. This type offers capacities up to 100 kN with compensated temperature performances. Cable is contained within a stainless steel spring for strain relief purposes for additional protection.
-
Product
DC Load Simulating Inductors
-
Osborne has developed a wide range of DC load simulation inductors that are known for the transients they produce. Osborne DC load simulation inductors are unique and innovative because they are engineered to produce a precise time constant current transient during the current charge cycle.Another distinguishing feature of our load simulation inductors is that they produce a precise voltage transient during the current discharge cycle. The resulting test circuit can be used to accurately replace real loads in a variety of circuit simulation applications.
-
Product
Solar Simulator for Concentrator Cells
-
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
Product
Heavy Duty Shear Beam Load Cells
SBL SERIES
-
The SBL Series heavy duty shear beam load cells are ideal for process weighing and for use in low profile industrial scales. These economical load cells are easy to install and durable in the field. Environmental protection is afforded through water resistant potting, a compression sealed and strain relieved cable entry, and corrosion resistant nickel plated steel.
-
Product
Small Compressive Load Cell
CCSM-3.0
-
DLM’s range of Small Compressive load cells can be used independently or in combination as part of weighing platforms.
-
Product
Portable Range Threat Simulators
Simulator
The Textron System's PRTS™ and HPRTS™ are medium and long-range, programmable, ruggedized Radio Frequency (RF) test and training tools. Our PRTS family of range simulators delivers high-fidelity environments for training ranges.
-
Product
500 Watt Electronic Load Module
N3305A
Load Module
The Keysight N3305A is a 500 W (0-60A, 0-150V) electronic load module for use in either the N3300A or N3301A electronic load mainframe in system applications. The N3305A load module is fast and accurate, for programming in constant current, constant voltage, or constant resistance modes, or for making voltage, current or power measurements. The N3305A can also digitize waveforms.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCI With 2 Or 4 CAN Bus Nodes
ACP825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCI with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825-x PCI card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
Battery Cell Simulation / Emulation
BMS
-
Efficiency, reliability and safety of modern lithium ion batteries for electric vehicle drives strongly depend on the battery management system (BMS) as their electronic control unit.
-
Product
Solar Simulator for Multijunction Solar Cells
-
For series connected multijunction cells, at a given spectrum (e.g. AM 1.5 or AM 0 for space solar cells), one of the cells will limit the current in the series connection of cells. All solar simulators deviate from the true AM 1.5 spectrum, and they are only classified in wide spectral bands (100nm width). So even for class A or A+ solar simulators, it can easily happen that the bandgaps of the multijunction cells are such distributed that the 'wrong' cell will limit the current, if a solar simulator with fixed spectrum is used. In the 70s and 80s, when these measurements were first developed, intercomparisons showed deviations of cell efficiency in fixed spectrum solar simulators of more than 40%.
-
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 350
40-265-016
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Load Cells
-
A load cell is a sensor which transforms the load or force applied to it into an electrical signal. Load cell sensors are based on the strain-gauge principle i.e. a sensor whose resistance varies with applied force. They are the most widely used as load transducers in all areas of weight measurement from retail scales, the process industry and medical applications.
-
-
-
