SD Card
A non-volatile memory card format.
-
product
Embedded MXM GPU Module with NVIDIA RTX™ A2000
EGX-MXM-A2000
- NVIDIA Ampere Architecture- Standard MXM 3.1 Type A (82x70mm)- PCIe Gen 4 x8 interface- 2560 CUDA® cores, 20 RT Cores, and 80 Tensor Cores- 8.25 TFLOPS peak FP32 performance
-
product
32Ch Isolated Output Card
SET-1320
This card offers 32 optically separated open collector outputs that can switch up to 100mA at 60V. SET-1320 combines tight IO with high isolation voltages and an extensive output voltage range.
-
product
PCI-Express Generic Carrier Card
ACPx-1
PCI-Express generic carrier card for XMC (PCI-Express bus mezzanine card) with 1 XMC slot. Modular solution combines any AIM XMC module for AFDX®/ARINC664P7, ARINC429, MIL-STD-1553 or any standard 3rd party, VITA 42.3 compliant XMC module.
-
product
Digital I/O Card
PCIe-DIO-120
This product is a x1 lane PCIe DIO board available in economy to high-performance models ranging from basic 72-, 96, and 120 DIO lines to advanced COS detection. The card emulates 8255 compatible chips using FPGA technology, providing up to 120 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs.
-
product
Dynamic Digital I/O With Per Channel Timing, Programmable Logic Levels And PMU PXI Card
GX5296
The GX5296 offers advanced dynamic digital I/O performance and capabilities in a single slot, 3U PXI format. The 32-channel, GX5296 features timing per pin, multiple time sets, data formatting, and an advanced sequencer – providing users with the capability to emulate and test complex digital busses for system, board or device test applications. Offering sub-nanosecond edge placement resolution per pin and a PMU per pin, the GX5296 has the ability to perform both DC and AC parametric testing. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
product
2- to 8-Channel Anti-Alias Low-Pass Filter and Instrumentation Amplifier Card
AAF-3PCI
The AAF-3PCI is a 2- to 8-channel anti-alias low-pass filter and instrumentation amplifier PCI bus plug-in board for front-end signal conditioning in PC-based data acquisition systems.
-
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm
40-294-024
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Real-Time Vision I/O Card With Multifunction
AX92350
The AX92350 is a PCI Express x1 vision card with vision-specific I/Os and real-time controls. A machine vision system requires accurate interaction between lighting, camera, actuator and sensor devices. The AX92350 vision I/O card integrates LED lighting controller, camera trigger, encoder input, and digital I/O to connect and control all the vision devices. The encoder input function is well-suited for conveyor applications. There are 4-CH trigger input, 4-CH or 8-CH trigger output, 4-CH LED lighting control, 1-CH quadrature encoder, 8-CH isolated DI and DO, and 1-CH auto measurement function for rugged machine vision and video surveillance applications.
-
product
PCI Express Card
Axiomtek develops a full spectrum of PCI Express cards to help customers accelerating their design and reducing development costs.
-
product
Arbitrary Waveform Function Generator PXI Card
GX1110
The GX1110 is a high performance, single-channel PXI arbitrary waveform generator that offers function generator and arbitrary waveform generator functionality within one instrument. Built-in waveforms are available for use with both the DDS or AWG modes of operation and include Sine, Triangle, Ramp, Noise, Gaussian pulse and Sinx / x. A flexible sequencer is also available as part of the AWG's architecture, supporting the generation of complex waveforms.
-
product
6U VME D/S, S/D, I/O & Comm Board
64CS4
NAI’s 64CS4 is a 6U VME multifunction I/O board designed for applications requiring Digital-to-Synchro/Resolver (D/S) stimulus output, as well as I/O and communication functions. This board contains five intelligent, function module slots. The board can be configured for 10 D/S channels, or for D/S in combination with I/O and communication modules. Additional enhancements include FIFO data buffering for select modules. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
product
Power Interface and Prototype PXI Card
GX7404
The GX7404 power interface board offers a low cost method for providing controlled power to UUT interface and test circuitry. The GX7404 provides +5 V, +3.3 V, +12 V, and -12 V voltage outputs which are present on the PXI motherboard to be switched through a DB25 connector for use by a UUT (unit under test) and / or interface circuitry.
-
product
Matrix C-Size Switch Cards
Explore our array of matrix switch cards, each with a unique function for your application.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 63.7 Ohm
50-294-011
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Probe Card
T40™ Series
Ultra low noise and fast settling modeling and characterization tests are made possible by Celadon’s patented ceramic probe cards.
-
product
SmartNIC Storage Accelerator Card Zynq Ultrascale+
iW-RainboW-G35P®
Your product description goes here.
-
product
SCSI Fast/Wide Differential VMEbus P2 Paddle Card
1870
Our SCSI Fast/Wide Differential VMEbus P2 Paddle Card (1870) use a 68-pin SCSI Fast/Wide connector to bring out multiple ports. Transition panels and paddle cards are intended to adapt the 68-pin connector to more traditional connectors used in applications.
-
product
PCI Precision Resistor Card 4-Channel
50-297-130
The 50-297 PCI precision resistor provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 range is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Digital I/O Card
PCIe-DIO-48JPLS
The PCIe-DIO-48JPS is a 48 channel PCI Express (PCIe) card designed for use in a variety of digital I/O applications. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program. This also allows for simple and trouble-free migration from other ACCES PCI digital I/O cards.
-
product
Isolated Digital I/O Card
mPCIe-IDIO-8
The mPCIe-IDIO-8 consists of a type F1 PCI Express Mini Card (mPCIe) interface board that connects to a Mobile-ITX-sized, DB-37M Isolation Module via an included 9” cable. That module is designed to be easily panel-mounted in any application environment. It uses the high speed PCI Express bus to transfer digital data to and from the card. The digital I/O is compatible with 8255 PPI chips making it easy to program.
-
product
PCI Relay Driver Card, 64-Channel
50-411A-001
The card provides 64 channels of low side switching for external relays. Users need to simply connect a positive voltage source to one terminal of a relay coil and the other terminal to an output of the 50-411A. Each output is capable of sinking up to 1A of continuous current.
-
product
PCI High Density Pecision Resistor Card, 3-Channel, 4Ω To 22.3MΩ
50-298-154
The 50-298-154 is a high density programmable resistor card with 3 channels which can be set between 4Ω and 22.3MΩ with 2Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
BNC Box-D37M To 16 SE BNC Outputs For 12-Bit PCMCIA DAQ Cards
CB516S
*D37M input connector*16 Single Ended BNC output channels*Connects from Ines or Elan 12-bit PCMCIA DAQ cards via CBL-T30-32-D37F cable*Only for Ines or Elan 12-bit PCMCIA DAQ cards
-
product
PCI Strain Gauge Simulator Card, 2-Channel, 3k
50-265-102
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
Resistor Simulation Card
SET-1210
The card has two ranges of values that meet the requirements of most functional test systems.The SET card is designed for applications in which resistive sensors provide information about parameters such as temperature (e.g. when testing motor controls)Each channel of the SET-1210 resistor simulation card is able to simulate the common short-circuit and no-load conditions, which can occur in a system due to faulty wiring or sensors.
-
product
PCI Strain Gauge Simulator Card, 6-Channel, 350 Ohm
50-265-016
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
SLSC Cards
SET offers a variety of different signal conditioning cards for connecting DUTs. The platform is designed to allow additional cards to be developed effectively in terms of cost and time.
