Filter Results By:
Products
Applications
Manufacturers
VDE
Verband der Elektrotechnik
-
product
Impulse Tester
MIG2412SPD
The MIG2412SPD is a impulse tester for testing SPD (Surge Protection Devices) in accordance with IEC 61643-1 and VDE 0675. Up to maximum 24kV/12kA making it suitable for testing Class I to III or in accordance with VDE Class A,C, D. The MIG2412SPD is a hybrid generator with a voltage wave shape 1,2/50 ìs at "no load" and a current wave form 8/20 ìs at short circuit for testing Class III (D) SPD connected to power line.
-
product
General Power Relays
Panasonic Industrial Devices Sales Company of America
2A and greater load rating in Polarized, Non-Polarized, High Capacity DC, General Purpose, and Safety configurations. UL, CSA, C-UL, TUV, VDE, and SEMKO certifications.
-
product
Insulation Meters
Here you will find an insulation tester for a variety of ranges between 50 mega ohms and 2000 mega ohms. The portable manual insulation tester is used for determining insulation resistance, continuous current, alternating current and testing. With an insulation tester, measurements can be taken for different voltages, beginning with 100V up to 10,000V. Measurements meet the DIN VDE 0413 part 1 standard. The insulation tester comes with a test mechanism, clips, batteries and a carrying case. The insulation meter can be equipped for test laboratories if an optional DIN EN ISO is acquired.Measurement of insulation in cables and motor coils is vitally important for the prevention of accidents and damage to installations and is obligatory according to most codes of conduct.
-
product
Installation Testers
Offers two models that verify the safety of electrical installations in residential, commercial and industrial applications. Has been developed to carry out the following safety measurements of electrical installations in accordance with EN 61557 and DIN VDE 0100: Insulation resistance, RCD tests, Low Ohm resistance, Earth ground resistance, Loop impedance, Phase sequence.
-
product
Single, Double Power Cord Tester
LX-30A+
Shenzhen Lian Xin Technology Co., Ltd.
Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .．·used to test single – ends ,double –ends ,three-ends power supply cords.．·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,．·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,
-
product
Installation Safety Testers
PeakTech Prüf- und Messtechnik GmbH
This innovative combination meter for testing electrical installations according to VDE 0100 convinces by its technical performance in the high-end range.With the large 3.5 "TFT color display all important safety checks as the RCD-, Voltage-, Loop-, Low-Ohm, Earth resistance and Insulation tests for annual safety-checks and newly installed systems can safely be carried out by the responsible electrical engineer.Since this new development was designed only according to the latest standards, the required measuring values can be even more convenient stored with an App (iOS / Android) via Bluetooth on the mobile phone, saved to an SD card or, when work is completed, from the internal data memory via USB connection to a PC.
-
product
12.5 mm Test Sphere Probe
CX-12.5
Shenzhen Chuangxin Instruments Co., Ltd.
The rigid sphere (12.5 mm) from Autostrong is designed and manufactured to perform the test specified in many standards (IEC 60335, IEC 60065, IEC 60745, IEC 61029, IEC 60950) to prove the degree of protection for the first characteristic numerals 2 (IP2X) .Its is designed to meet the requirements of international safety regulatory agencies such as UL, DNV, IMQ, BVSQ, ITS, IRAM , CSA, VDE, DIN , INMETRO.
-
product
Rotary Field Direction Indicator According to DIN EN 61557-7 (VDE 0413-7)
PeakTech Prüf- und Messtechnik GmbH
Direction indicators are indispensable for use in the electrical assembly of three-phase motors. This offers two different functions for displaying the direction of rotation. I
-
product
Voltage Testers
DUSPOL
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
product
Design & Manufacturing Services
Since its inception, APLAB has been serving the Global Market with a wide range of Electronic Products meeting the International standards for safety and reliability such as UL, VDE, etc. APLAB enjoys worldwide recognition for the quality of its products, our business integrity and innovative engineering skills.
-
product
IEC60335 Inclined Plane Test Table for Stability Test
CX-W600
Shenzhen Chuangxin Instruments Co., Ltd.
It's to determine the stability of electric appliances which are used on a table or on the floorin accordance with IEC 60065 / 1998-07 clause 19.1, IEC 60335-1 / 1991-04 clause 20.1, IEC 60601-1 /1988 clause 24.1, IEC 60950 / 1991 + Amendments, modified, clause 4.1.1,EN 60335-1 / 1994 and A11 / 1995 clause 20.1, EN 60950 / 1992 + Amendments up to 1997 clause 4.1.1,VDE 0700 Part 1 / 10.95 clause 20.1 and Part 3 / 3.96 clause 20.1, VDE 0730 Part 1 / 3.72 clause 20a,VDE 0805 / 11.97 clause 4.1.1Inclined Plane Device is used to test the stability of an apparatus that requires a surface in order to work.The device cosist of a surface and an angle adjusting device with 0- 15 °
-
product
BSV Systems
In the medical field, electrical devices are used on which people's lives or healing processes depend. The highest demands are therefore placed on the devices required in the operating room or intensive care unit. Gustav Klein BSV systems guarantee an uninterrupted and safe power supply in accordance with VDE 0100 and ÖVE/ÖNORM E 8007.
-
product
PD Measuring System
TEM
Partial discharge test system for laboratory or on-site measurement according to VDE 0434, IEC 60270 and EN50178 consisting of:*Partial discharge meter TMG*High-voltage coupling capacitors for decoupling of the PD pulses*Partial discharge calibrator TPK for determining the correction factor in the PD test circuit
-
product
Earth Meter
EM-4055
The EM-4055 Earth Meter is a digital, microprocessor-controlled instrument that allows to measure the earth resistance and ground resistivity (using Wenner´s method), as well as to detect parasitic voltages present in the ground. This instrument is well suitable to measure earth systems in power substations, industries, distribution networks, etc., according to VDE 0413. It is also suitable for soil resistivity measurements, in order to optimize the earth systems project
-
product
Loop Resistance Measuring Device According to DIN EN 61557-3 (VDE 0413-3)
PeakTech Prüf- und Messtechnik GmbH
A loop tester which is used to test the safety of electrical systems. These device measures the impedance of the short-circuit loop between the outer conductors of a circuit, whereby the probable short-circuit current is calculated. The protection of the circuit (miniature circuit breaker) must therefore trigger at a lower current than the expected short-circuit current, in order to avoid excessive heating of the lines and thus a fire risk. The PeakTech 2715 is due to its function and its robust design almost indispensable when performing new installations, but also for general checking of electrical systems, this device is the ideal companion.
-
product
IP code Testing
Educated Design & Development, Inc.
Complies with various IEC, EN, CE, VDE, UL & CSA requirementsUnit comes with NIST traceable / ISO 17025 accredited certificate of calibration.ED&D is ISO 17025 accredited by ACLASS, an ILAC Member. Measurement data and uncertainty data is available.Uses RTS-01 Rain Spray Head
-
product
KPG 24kV VLF Test Set
Kilovolt Prueftechnik Chemnitz GmbH
The portable cable test set KPG 24kV VLF is used for testing of medium voltage cables in accordance to the standards IEC 60502-2, CENELEC HD 620 & 621, DIN VDE 0276/620 & 621 and IEEE 400.Test is carried out with a low strain practice with VLF (very low frequency) test voltage of preferably 0.1Hz.VLF testing enables detection of damages of insulation within shortest test time.
-
product
Electrical Safety Testers- Hipots
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.GW Instek’s GPT-9900/GPT-9800/9600 series safety testers(hipot test) provide safe and quick measurement tools for AC/DC withstanding voltage tests, insulation resistance tests, and AC ground bond tests. Those tests are required by many international safety regulations such as CE, UL, VDE, and etc. We also have leakage current tester, GLC-9000, which supports all the major leakage current test standards for medical and general electronic equipment.
-
product
Partial Discharge Meter
TMG
The partial discharge meter TMG was developed for Partial Discharge tests according to VDE 0434 and IEC 60270.
-
product
Combination Measuring Devices According to DIN EN 61557-10 (VDE 0413-10) are permitted
PeakTech Prüf- und Messtechnik GmbH
This innovative combination measuring device for testing electrical installations according to official laws convinces with its technical performance data in the high-end area. All important safety tests such as FI, voltage, loop, low-resistance, earth resistance and insulation tests for e-checks and new installations can be carried out safely by the electrician via the large 3.5“ TFT color display. Of course, the device comes with an extensive range of accessories, such as all necessary test leads, adapters, rods and the required software CD for the PC. The device can be charged with a power adapter or via a car adapter. During the daily use, this high-quality device is protected against dust and all-round water jets by its protection class IP 65.
-
product
Dipole Antennas
Provides reliable, repeatable measurements. Suitable of FCC, MIL-STD, VDE, Tempest and Immunity stesting.
-
product
High Voltage
Accurate measurement of high voltages acc. to VDE 0432 und IEC 60060 in conjunction with a high voltage divider.For the measurement, the principle of capacitive or resistive divider is used, which can be selected in the peak voltage meter.
-
product
Measuring Device for Testing the Effectiveness of Residual Current Protective Devices (RCD) According to DIN EN 61557-6 (VDE 0413-6)
PeakTech Prüf- und Messtechnik GmbH
A residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE).
-
product
Insulation Measuring Device According to DIN EN 61557-2 (VDE 0413-2)
PeakTech Prüf- und Messtechnik GmbH
This digital insulation measuring device is required for various measurements of cables, components and their insulation.
-
product
[5kV AC] Hipot Tester, Rise/Fall-Time Control Function Equipped
TOS5200
TOS5200 is designed for AC Hipot Test with 500 VA capacity and 200 mA short circuit current output capability. Equipped with the PWM amplifier, the TOS5200 can provide a stable & reliable output without being affected by ACpower line. Therefore, it is a perfect solution for electronic equipment or devices complied to IEC, EN, UL, VDE andJIS etc. requirement.As TOS5200 covers most of features of our upper class model for AC Hipot Test, it achieves thesuperb cost / performance ratio for those who need 200 VA or 500 VA capacity, or both. Also, as it equips the Interlockfunction together with other safety features, operator can carry out the test with higher current value in safe.
-
product
[5kV AC/6kV DC] Hipot and Insulation Resistance Tester, Rise/Fall-Time Control Function Equipped
TOS5300 Series
The "TOS5300 Series" is a series of test instruments used in Hipot (withstanding voltage) tests and insulation resistance tests, two of the four tests regarded as necessary for ensuring the safety of electrical products. With an output of 5 kV/100 mA (AC) and 6 kV/10 mA (DC), the series can be used in Hipot (withstanding voltage) & insulation resistance testing of electronic equipment and electronic parts, based on the requirements of IEC, EN, UL, VDE, JIS, and other international safety standards and the Electrical Appliance and Material Safety Law. Also, the test voltage stability is improved with the adoption of a newly developed switching amplifier. Since the output voltage can be kept constant even when the AC line voltage or frequency changes, consistent testing can be performed, even when the power supply environment is in an unstable region. The TOS5300 is also equipped with a number of features that are capable of meeting a variety of test needs. It is a new low-cost standard model that provides thorough operability, reliability and safety.
-
product
Earth Resistance Tester
PeakTech Prüf- und Messtechnik GmbH
A Rugged sealed digital earth tester is built with all the protection you need for outdoor use. The instrument is suitable for the testing of single earth electrodes such as lightning conductors and other small earthing systems according to VDE 0413. The resistance of conductors such as continuity and conduit coupling joints can also be measured. Two-terminal operation measurement, which reduces the accuracy, can also be done by shorting P and C terminals. It has an advanced circuit design that permits the instrument to operate with the minimum influence from earth voltage and earth resistance of the auxiliary spikes.
-
product
Peak Voltage Measurement
In high voltage measurement technology, the peak value, or the effective value, of the voltage is determined in accordance with VDE 0432 or IECV 60060. The peak voltage measuring device from MPS Mess- & Prüfsysteme GmbH can measure these two values in connection with a high voltage divider (capacitive or resistive). In the event of flashovers in the high-voltage circuit, this is indicated in the SMG.
-
product
Socket-Outlet Torque Balance
CX-L12
Shenzhen Chuangxin Instruments Co., Ltd.
For measuring and testing the torque strain exerted by appliances with plug pins on socket-outlets in accordance with IEC 60065/1998-07 § 15.4.1 Fig. 11, IEC 60335-1 / 1991-04 § 22.3, IEC 60884-1 / 1994-06 § 14.23.2, EN 60335-1/1994 + A11 /1995 § 22.3, EN 60950/1992 + Amendments up to 1997-03 § 4.3.18, VDE 0700 Part 1 /1995-10 § 22.3, VDE 0805/1997-11 § 4.3.18
-
product
Two-Pole Voltage Tester According to DIN EN 61243-3 (VDE 0682-401)
PeakTech Prüf- und Messtechnik GmbH
Two-pole voltage testers, are ideal for quick and uncomplicated voltage measurements.
