Relay Test Sets
See Also: Relay Test, Test Sets
-
Product
PXI/PXIe Power Relay Module, 5xSPST, 30 Amp
42-166-002
Relay
The 40/42-166-002 is a PXI/PXIe high density power relay module with 5xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
Level Test Set
ET 91
-
100 Hz to 2.4 MHz selective/wideband Level Meter & Generator,with Spectrum Analyser and Z/RL/LCL Bridge
-
Product
Loss Test Set, Return Loss Test Set
LTS1315, LTS1315R
-
The KD Optics LTS1315 is a combined mains / battery powered laser source and power meter designed to make attenuation testing in the field easy, reliable and most importantly, consistent. The LTS1315R incorporates return loss measurement (RLM) capability with the ability to switch very easily between dBrel and return loss.
-
Product
PCI 50xDPST Reed Relay Card
50-115A-122
Reed Relay
This is the 50xDPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PXI/PXIe Power Relay Module, 10xSPST, 30 Amp
42-166-001
Relay
The 40/42-166-001 is a PXI/PXIe high density power relay module with 10xSPST switches rated at 30A. The 40/42-166 range is available with SPST, SPDT or SP4T switching configurations.
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 18GHz, 50Ω, SMA, Internal Termination
40-781A-022
Relay
The 40-781A-022 (PXI) and 42-781A-022 (PXIe) are dual SPDT 18GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Optimize Throughput And Cost For MmWave 5G Device Functional Test
Functional Test
Test engineers always have faced tough new test-coverage challenges. Those introduced by 5G measurements at mmWave are no exception, as they require over-the-air (OTA) radiated test solutions. But never have these pressures seen today’s intense time-to-market, manufacturing volume, and operational expectations! A solution that meets these demands must:
-
Product
Switching Test Set
U3020AS26
Matrix Switch Module
The Keysight U3020AS26 is a switch matrix that consists of two single-pole-six-throw (SP6T) switches. It allows switching of multiple signal paths without physically changing the connections. This allows multiple tests to be performed with the same setup, eliminating the need for frequent connects and disconnects. An entire testing process can be automated, increasing the throughput in high-volume production environments.
-
Product
PXI-2568, 31-Channel, 2 A, SPST PXI Relay Module
778572-68
Relay
31-Channel, 2 A, SPST PXI Relay Module—The PXI‑2568 is a general-purpose switch module that features independent single‑pole single‑throw (SPST) Form A armature relays. Each relay is nonlatching with very low on-resistance and low thermal offsets. The PXI‑2568 is fully software programmable. With an efficient coupling of voltage/current capability and relay density, this switch module is ideal for automated test equipment (ATE) loads or for controlling heaters, lights, and fans.
-
Product
PXI/PXIe Power Relay Module, 36xSPST, 5 Amp, 50-pin SGMC Connectors
40-153-002
Relay
The 40/42-153-002 is a PXI/PXIe high density power relay module with 36xSPST switches rated at 5A. User connection is via 2x50-pin SGMC male connectors. The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock. Electro-mechanical power relays are used which are suitable for switching loads up to 5A at 250VAC.
-
Product
PXI Dual Microwave SPDT Relay 18GHz 50 SMA - Internal Termination
40-781-022
Relay
This dual microwave SPDT relay module is part of the 40-781 range that consists of one or two changeover switches capable of switching frequencies to 18GHz in 50 Ohm. Versions are available with either internal or external terminations and connections are made via front panel mounted high quality SMA RF coaxial connectors.
-
Product
PXI General Purpose 2A Relay Module 32xSPST
40-132-201
Relay
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
Open Test Platform for High Performance Automotive Applications
TSVP
Test Platform
The R&S®TSVP family of products is an open test platform from Rohde & Schwarz ideal for high performance automated test equipment (ATE) applications. The chassis contains a mechanical frame, digital backplane, analog backplane, mains switching and filtering, power supply and diagnostic extensions. A highlight is the analog bus for routing measurement signals between different slots without additional external wiring.
-
Product
PXI 40Amp 14Volt 2xSPST Automotive Relay
40-180-001
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDCThe 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
OTP-Based Test System
Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
Product
Optical Loss Test Set
OLTS
-
Tests for the total amount of light loss on a fiber optic link.
-
Product
CT/PT Test Set
PCT200Ai
-
PCT200Ai is the CT/PT test set (current transformer analyzer) that can finish various current transformer test of different CT and plus reference testing functions of PT. Compared with PCT200i, its accuracy is higher.
-
Product
PXI/PXIe Power Relay Module, 50xSPST, 5 Amp, 50-Pin SGMC Connectors, With Interlock
42-153-001-HI
Relay
The 40/42-153-001-HI is a PXI/PXIe high density power relay module with 50xSPST switches rated at 5A and includes the hardware interlock option. User connection is via 2x50-pin SGMC male connectors, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied).
-
Product
PXI/PXIe Microwave Relay, Dual SPDT, 50 GHz, 50 Ω, SMA-2.4, Remote Mount, Failsafe
42-780B-552-E
Relay
The 40-780B-552-E (PXI) and 42-780B-552-E (PXIe) are dual failsafe SPDT 50 GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PCI 26xSPDT 2Amp Relay Card
50-131-002
Relay
The 50-131-002 26xSPDT relay module is part of our range of PCI, low cost, general purpose electro-mechanical relay modules which are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching modules do not have sufficient voltage or current carrying capability.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 18 GHz, 50 Ω, SMA, Internal Termination, Failsafe, Remote Mount
40-781A-021-E
Relay
The 40-781A-021-E (PXI) and 42-781A-021-E (PXIe) are single failsafe SPDT 18 GHz microwave relay modules with internal terminations and remotely mounted relays. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
2-Module ICT System, I317x Series 6
E9902G
In-Circuit Test System
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
Product
PXI Mixed Configuration Relay Module - 9 Cells Populated
40-138-AA-BB-CC-DD (9 CELL)
Relay
The 40-138 2A Relay Module with 9 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Ultra High Density 4mm Reed Relays
120-1-A-12/1
Reed Relay
Single Pole Reed Relays0.5 Amp switchingVery high packing densityStacking on 4mm x 4mm pitch1 Form A12 V Coil
-
Product
Insertion Loss Test Set
-
OptiConcepts FiberWarrior Pro™ Insertion Loss Test Set is used for the following functions: continuity check, fiber loss, return loss, and connector loss for OEM, lab, and production use as well as transport, metro, access, and FTTx/PON networks. The FiberWarrior Insertion Loss Test Set performs single-mode and multimode loss measurement functions, including single component and multi-fiber testing.
-
-
Product
RAMP TEST SET
AN/USM-719
-
Tel-Instrument Electronics Corp.
Based on entirely new up-to-date technology and digital architecture; the AN/USM-719 large 4.75" x 3.5" in. color LCD screen and surrounding soft-keys and keyboard provides easy and quick access to a multiple of test screens menus, and display options affording single man operation, instant results, and a host of pre-programmed and manually variable parameters to meet the most demanding requirement's for testing of advabced airborne avionic and transponder/interrogator systems.
-
Product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Relay
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
LXI Reed Relay Matrix - Dual 64x8 Plugin, Direct Y Access, 6 Analog Buses
65-223-001
Reed Relay
The range includes four plug-in models covering matrices of up to 1,536x4 in increments of 128 (model 65-221), 768x8 in increments of 64 (model 65-223), 384x16 in increments of 32 (model 65-225), and 192x32 in increments of 32 (model 65-227). Users can specify as many or as few plug-in modules (up to six) required and can field upgrade the chassis to extend the matrix when necessary. Another important feature is that over 1,500 relays can be closed simultaneously for specific conditions for parametric testing.
