Inductance Decade Boxes
See Also: Decade Box, Resistance Decade Box, Capacitance Decade Boxes
-
Product
Edge AI Box
-
Arm-based edge AI boxes are powered by NXP, NVIDIA and Rockchip. They provide AI inference capabilities in a low-power fanless design.
-
Product
Connector and Breakout Box
ES4640
-
The ES4640 Connector Box offers a standardized wiring and connectivity for HiL testing systems in the powertrain domain. Its front panel provides connectors for the ECU, CAN bus communication, on-board diagnostics, and LEDs for ignition and injectors. Its rear panel connects loads, failure simulation, and other components. Sample applications of the ES4640 are closed loop HiL systems for 8 cylinder gasoline and diesel engine ECUs.
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
IEC60335-2-9 Clause 3 Figure 104 Vessel For Testing Induction Hotplates
CX-104
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60335-2-9 clause 3 figure 104 Vessel for testing induction hotplates Parameter : Pot and lid material is mainly Q235, carbon mass fraction <0.08%; 2. The thickness of the wall material is 2 mm;3. The bottom of the pot body can not be outward convex, can not exceed 0.05mm; 4. Pot body and lid surface to be clean 5, size: 110, 145, 180, 220, 300mm each one
-
Product
Unclamped Inductive Load Tester
ITC55600C
-
Model ITC55350 is the high current (600A) version of theITC55100 tester. The ITC55350 performs the same testsas the ITC55100 and includes many features that improvetesting accuracy, test results collection, test resultsviewing, and multiple tester networking
-
Product
Fifo Serial Analyzer 2 TO 1 Breakout Boxes
FLL221/FLL221S
-
The FLL221 BreakOut Box is designed to be used with the FLL and FSA serial analyzers when they run on PC's with only one ComPort. The serial line passes through FLL221 using the 9-pin connectors. Data from both pin 2 and 3 of the serial line is available on the FLL221 output. The output cable from FLL221 is connected to the ComPort of the PC running the analyzer.
-
Product
Inductive Motor Control
-
The inductive motor control position sensor family detects the electrical position within one pole-pair of a rotating shaft and can be used for the motor commutation of a brush-less DC (BLDC) motor. Based on the inductive sensor technology, this family measures the coupling between an excitation coil (TX) and two receiver coils (RX) via a rotating target. The coils are executed as printed circuit coils and the rotating target is a simple punched metal part. With the correct layout of the coils and the target, both synchronized to the number of pole-pair count of the motor, the IC output is proportional to the electrical angular position within one pole-pair segment with increased resolution and high performance of only 0.3° electrical INL!
-
Product
RF Shielded Box
LTL D7001
-
LTL D7001 RF Test Enclosure is the streamline solution to manage your RF Testings. LTL D7001 RF shielded test enclosure can comfortably house the intermediate device on test.LTL RF Enclosures are available in aluminum and stainless steel models and come with a specialized EMI gasket which enables stable and effective RF shielding performance in all frequency bands.
-
Product
Inductive Sensors
-
Inductive sensor designed to detect shaft speed, shaft position, gate position, or object presenceTotally sealed constructionMulti-voltage 24 - 240 VAC/VDCDetects ferrous targets up to 5/16" (8 mm)IP 65 Protection
-
Product
Shielded box
-
Gtemcell develops a wide range of shielded box for commercial, industrial and military applications. Customized solutions according your needs!
-
Product
Decade Capacitor
1419 Series
-
GenRad 1419-A and GenRad 1419-B (Polystyrene) Owing to its very low dielectric absorption, the GenRad 1419A 3 Decade 1000 pF/step & 1419B 4 Decade 100 pF/step Polystyrene Decade Capacitors are particularly useful in research and development work on computer and integrator circuits and on low-level amplifiers. Its constancy of capacitance and dissipation factor as a function of frequency also makes it extremely useful in measuring circuits and as a component in filters and tuned circuits. High insulation resistance and low dielectric absorption make it the 1419 Decade Capacitor a nearly ideal capacitor for dc work.
-
Product
Stationary Sensor Box
S-SB10
-
The S-SB10 can be operated with both airborne and structure-borne sound probes. This allows very versatile conditions and processes to be monitored. For example, airborne ultrasound can be used to detect turbulent flows of gases at leakages as well as partial discharge processes at electrical systems. Both processes generate high-frequency ultrasonic signals .
-
Product
Smart Inductive Analog Measurement Sensors (AMS)
-
Contrinex Smart Inductive Analog Measurement Sensors (AMS)
-
Product
Optical Switch Boxes
-
An optical switch box is needed so that automated test platforms can permit the system to measure the performance of transmitters and receivers at multiple wavelengths or channels. The MLO4034 Optical Switch Box incorporates a WDM demultiplexer, integrated power meters, variable optical attenuators, and optical switches to form an integrated switch matrix. It enables receivers and transmitters to be tested at up to four wavelengths or channels.
-
Product
OTDR Launch Cable Box, OTDR Dead Zone Eliminator 100-500M
-
Shanghai Fibretool Technology Co.,Ltd.
Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.
-
Product
Inductive Measuring Probes
-
• Inductive measuring probes specially designed for measurement by comparison• Available in 2 versions: spring push and pneumatic push• Long life precision bearing guidance (tested up to 13 million cycles)• Resolution <0.0001 mm• Repeatability 0.15 μm• Measuring range +/- 2mm and +/- 5 mm• Compatible with D300SV2, D70i and D400S units through M-Bus multiplexer units• High data speed• Operating temperature +10 to +80°C• IP65 protected
-
Product
Test Boxes/Launch Boxes
-
Whether they are called a launch box, pulse suppressor, or launch cable they all do the same thing. When technicians conduct a quality test to look for fiber optic cable breaks and light loss in your installed network you need to eliminate what is called the "Dead Zone". When testing fiber optic cable with an Optical Time Domain Reflectometer (OTDR), these launch boxes eliminate the "Dead Zone". Without a launch box it is difficult to measure the relative loss at the near end and far end of the patch panel connections.
-
Product
Fifo Serial Analyzer Breakout Box
FLLBOB
-
FLL BreakOut Box FLLBOB is a breakout box specially designed to be used with the FLL and FSA serial analyzers. With FLLBOB it is easy to connect the PC to the serial line without having to make dedicated cables.
-
Product
Breakout Box
-
A piece of electrical test equipment used to support integration testing, expedite maintenance, and streamline the troubleshooting process at the system, subsystem, and component-level by simplifying the access to test signals
-
Product
Cylindrical Compact Inductive Proximity Sensor
GX
-
Panasonic Industrial Devices Sales Company of America
The GX Cylindrical Inductive Sensor Series with a built-in amplifier comes in two versions - with and without a threaded section.
-
Product
Box Compression Testing Machine
-
Dongguan Kejian Instrument Co., Ltd.
Containers are subject to compressive forces when stacked and during transportation. It is vital to determine the compression strength of the box in order to make sure that the box will be able to resist the anticipated compressive forces and to determine the load that the box will be able to withstand during transit and storage.
-
Product
Standard Ratio Box For Calibration
ST-105
-
The ST-105 is a calibration box with standard ratios. It is used for calibration of any turn ratios measurement system. Housed in a rugged, waterproof case, it is very lightweight.
-
Product
Resistor Calibration Boxes
RCB-1
-
Standard Electric Works Co., Ltd
● The RCB-1 is used to verify and proof any High Voltage Insulation Testers. It can be utilized to calibrate all High Voltage Insulation Testers very accurately Analogs or Digitals.● Some institutions and large industries requested their own calibrator too, therefore, SEW started manufacturing the RCB for special customers.
-
Product
Box Recorders
-
Generous memory stores 500 event records and over a years worth of summary data. Graphs, charts and summary reports are easily produced using the included ProVision™ software package.
-
Product
Decade Boxes
-
Transcat stocks the decade boxes for your precision measurement applications. Using a series of resistors, capacitors or inductors, a decade box simulates electrical values. Switches are arranged in decades (sections of 10) where values from 0-9 are selected. Configured boxes can be substituted into a circuit as a component to determine the appropriate value for circuit operation. They can also be connected to input devices for testing. After connection to the decade box, a device should display a reading corresponding to the previously set box value. Our wide selection of decade resistance boxes include models that can serve as standards in verifying the accuracy of resistance-measuring devices. We offer a wide variety of boxes built by IET Labs, Prime Technology and AEMC.
-
Product
Multi-ratio CT Auto Test Box
PCT200 Series
-
The ATB01 PCT200 series Auto Test Box is specially designed as an accessory of PCT200i and PCT200Ai for automatic testing of the multi-ratio CT with multiple taps.
-
Product
Gold Box Power Supplies (AC-DC)
-
A broad selection of power supplies offering unusually high performance - many models have regulation of ±0.005%. Electronic current limiting and provision for remote voltage sensing are standard features; overvoltage protection is available as a built-in option. Rugged extruded aluminum cases include threaded mounting holes on bottom, back, and side, permitting mounting in any position.
-
Product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
-
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
Product
GPIB Controlled Signal Routing Box
3000GPIB
-
Test Electronics will customize the TE3000 GPIB signal routing box for your test application. Then, you simply rack and stack all the equipment, cable all the switched signals to the back of this GPIB box, add a rack mount computer, plug in the National Instruments GPIB board and software. Then run your customized GPIB based test system.
-
Product
Modular TPC - Computing Box Module With Intel Atom And Celeron CPU
TPC-B300
-
Computing Box powered by Intel Atom® X6425E/ Intel® Celeron® J6412 with DDR4 SODIMM slot (up to 32GB)Multiple sized front panel module offering with P-Cap multi-touch sensor (12.1" & 19" w/ robust 5-wire resistive touch)1 x Full-size mini PCIe for iDoor expansion1 x M.2 Key-E 2230 for WIFI + BT module1 x M.2 Key-M 2280 for SATA SSD1 x 2.5” SATA SSD expansion2 x 2.5Gb LANSupports TPM2.0 hardware securityWide Temp Support. Range -20~60 °C (Atom™ X6425E)
