Video Switching
The routing of video signals.
-
product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-C100-2
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
Video Signal Distributor
MSHM-305A/310A
MSHM-305A/310A, HDMI Distribution,Amplifier, distribute three digital video input sources to the five (or ten) output channels. The built in amplification function enables HDMI signal distribution without signal loss. The product guarantees to support full channels HDMI/HDCP compliance. User can select one input source of the three and make sure connected condition with led of the front panel.
-
product
3U VPX video capture/processing card
GRA115V
The Abaco GRA115V is a 3U VPX video capture and processing card based on NVIDIA® Turing ™ architecture with the latest Quadro RTX™ 3000 GPU. The GRA115V offers very high performance graphics and GPGPU capability – up to 5.3 TFLOPS floating-point - with CUDA™ and OpenCL™ support.
-
product
LXI Optical Switching - 16:1 Multiplexer Plugin Module
65-281-314
The 65-281-314 16:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
product
LXI Optical Switch - MEMS Dual 5x5 Matrix
65-280-422-M62.5
The 65-280-422 is a dual 5x5 fiber optic matrix plugin module designed to be fitted into a 65-200-002 Scalable Chassis. It uses multi-mode (62.5/125 μm) fiber and the optical interface is via front panel mounted LC high density connectors.
-
product
Coaxial Switch, DC to 18 GHz, SPDT, 12 to 15 V Solenoids
8761A
The Keysight 8761A is a single-pole, double-throw coaxial switch with excellent electrical and mechanical characteristics for 50 ohm transmission systems operating from dc to 18 GHz. It features broadband operation, long life, low SWR, excellent repeatability, and magnetic latching solenoids. The Keysight 8761A switch is small and lightweight, making it ideal for applications where space is limited. Because of its versatility and excellent electrical performance, it is well suited for automated testing and systems applications.
-
product
Detector Switches
Panasonic Industrial Devices Sales Company of America
Detector Switches are used to “detect” internal mechanical movements and convert human manual operations, such as the opening of a door , to electronic signals.
-
product
Test Switches and Accessories
FT Flexitest Family
The ABB FT test kit comes with a convenient carrying case to hold your hand held meter, test plugs patch cords, clips, and test probes in neat order. Patch cords are highly durable and flexible. Test switch accessories include: Test plugs Test kits Covers Interlocking bars Miscellaneous
-
product
PXI-2584 , 12-Channel, 600 V, 1-Wire PXI Multiplexer Switch Module
778572-84
12-Channel, 600 V, 1-Wire PXI Multiplexer Switch Module —The PXI‑2584 is a high‐voltage PXI multiplexer switch module that is ideal for fuel cell and battery stack applications. The reed relays in the PXI‑2584 ensure longer lifetimes and faster actuation times for test equipment. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Speed Switch
SCP1000/SCP2000
Features• Internal sensor• Over-or under-speed config., 1-990 rpm• 1 DPDT relay output (SCP1000), 2 SPDT relay outputs (SCP2000)• Built-in start delay• Dial-in calibration does not require power• 115, 230 VAC (50-60 Hz) and 12, 24 VDC power options• Works with Electro-Sensors magnetic pulser discs / wraps• Explosion proof housing• UL Listed Class I, Div I (C, D) Class II, Div I (E, F, G)
-
product
Switches
Electronic and mechanical vibration switches for overall vibration monitoring and trending without the necessity of complex systems. Models available with Hazardous Area Ratings and explosion-proof housing. Our state-of-the-art electronic switches are programmable to suit user needs.
-
product
3U VPX 1/10/40 GbE Switch
ComEth4082e
A cutting-edge 3U VPX Layer 2/3 Ethernet switch for hybrid copper-optical backplanes, the ComEth 4082e offers a high density of 1GbE, 10GbE & 40GbE ports and a high-level of switch configuration flexibility and rich layer 1/2/3 feature-set.
-
product
4-Port Coaxial Switch, DC to 18 GHz
8763B
The Keysight 8763B offers excellent electrical and mechanical performance with broadband operation, high isolation, low SWR, long life, and exceptional repeatability.
-
product
Thyristor Switch
Thyro-S
The highly efficient Thyro-S® thyristor switch delivers accurate, reliable, switch-free performance. Connect to bus systems, use as a stand-alone unit, or use in combination with all established two-point controllers — PLCs or computer systems. With simple mounting, minimal space requirements, quick commissioning, and safe operation, Thyro-S switches are seamlessly integrated into various applications. Status LEDs provide a quick overview of system status and load percentage.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
The 42-205-008 (PXIe) is an 8-channel fault insertion switch designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. It is available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
High Isolation USB Switches
RF gain block amplifier from Pasternack is featured in our extensive in-stock RF amplifier selection. Our connectorized gain block RF amplifier uses SMA connectors. This SMA gain block amplifier has a minimum frequency of 500 MHz, a maximum frequency of 2 GHz and a typical gain of 17 dB.
-
product
Ethernet Switch
VPX6-6902
Curtiss-Wright Defense Solutions
The VPX6-6902 is a combined management, control and dataplane switch for small, mid-size and large 6U VPX systems. Supporting a centralized switch architecture in both star and dual-star topologies, the VPX6-6902 is available with Serial RapidIO (SRIO) switching alone, or with both SRIO dataplane and Ethernet mangement/control plane switching all in a single VPX slot.
-
product
Optical Switch
Shenzhen Golight Technology Co.,Ltd
Optical switch is an instrument with optical path switching and optical channel expansion function. It can integrate different types of optical switch devices such as mechanical, MEMS, electrooptical, and magneto-optical according to user requirements.
-
product
Multiport Coaxial Switch, DC to 20 GHz, SP6T
87106B
The Keysight 87106B multiport switch improves insertion loss repeatability and isolation, which is necessary for higher performance test systems. The repeatability and reliability of this switch is vital to ATS measurement accuracy and can cut the cost of ownership by reducing calibration cycles and increasing test system up time. The Keysight 87106B terminated multiport switch provides the long life and reliability required for automated test and measurement, signal monitoring, and routing applications. Highly repeatable switching capability is made possible through Keysight's rigorous design and tight manufacturing specifications. Low insertion loss repeatability reduces sources of random errors in the measurement path, which improves measurement accuracy.
-
product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 75Ω, SMB
40-830A-006
The 40-830A-006 (PXI) and 42-830A-006 (PXIe) are 75Ω RF switches with 6 separate SPDT relays in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss.
-
product
PXI-2576, 64‐Channel, 2-Wire, Multibank PXI Multiplexer Switch Module
778572-76
64‐Channel, 2-Wire, Multibank PXI Multiplexer Switch Module —The PXI‑2576 is a multibank PXI multiplexer switch module with 16 banks of 4x1 2‑wire multiplexers. With the flexible architecture of the PXI‐2576, you can configure it in a variety of topologies that make it suitable for parallel measurement operations requiring low‐channel counts, or you can combine all multiplexer banks to form a single high‐channel‐count multiplexer featuring 64 2‑wire channels. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
product
Switch Fabric Modules
Switched fabrics provide the interprocess communication backbone for OpenVPX systems - and these modules enable you to achieve the maximum benefit.
-
product
Test Switches and Accessories
Test switches are designed and manufactured to allow quick and easy multi-circuit testing of switchboard relays, meters and instruments by any conventional system.These test switches and related test plugs have the features necessary for applications involving the measurement of individual currents and voltages associated with substation instrumentation and protection devices. They have been especially designed for the measurement of potential elements, current elements, and make-before-break short-circuit elements related to Current Transformer (CT) circuits.
-
product
LXI High Voltage Switching Multiplexer Plugin Module
65-231-907-HI
The 65-231-907-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
Switch Path Manager Lite License - SPM Lite
90-900-901
A low-cost "lite" version of our Switch Path Manager has a site license (can be used on unlimited PCs) and a boot limitation of two switching modules.
-
product
PXI Dual 32x4 Matrix 1-Pole Switching
40-534A-021
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
product
ColdFusion Switches
Chassis can be populated with any combination of Interface Blades making it the only L1 switch to support 10m to 128G in the same chassis.
-
product
SS Body Pressure Switch (longbody, NEMA 4)
P117LG
The P117LG NEMA 4 Stainless Steel Pressure Switches are the weather-proof, liquid-resistant version of the P117G. The NEMA 4 rating makes these rugged switches suitable for outside applications or in areas of condensing humidity. Unlike the P117G, the P117LG set point is factory set to customer specification and is non-adjustable.
