-
Product
Battery Cell Formation System
17000 series
System
Chroma 17000 series is specifically designed for the formation of Lithium Ion and Lithium Polymer secondary batteries. The 17000 series is a complete turn-key system, including carrier trays, robust battery probe contacts, high quality charge/discharge modules and intuitive software all under computer control. Patented Battery Voltage Tracking (BVT) DC-DC conversion power modules minimize power consumption in battery charging, and Energy Recycle Modules (ERM) recycle the discharged energy directly back to the DC power system for increased power efficiency. These power saving designs provide a planet friendly solution along with cost savings by reducing energy consumption. The intuitive software provides a flexible selection in the charge/ discharge channel, current rating, and modules under test. These features allow the Series 17000 to be used for final cell development, pilot line production, high volume production and ongoing reliability monitoring/quality control.
-
Product
48V / 300 Amp Load
BD18-48P-24/12
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 12V, 24V and 48V Battery systems and isextremely cost effective.
-
Product
DC Electronic Load
3110 Series（250W~700W）
-
Each 3110 Series stand-alone load has its own control and display panel, CC / CR / CV / CP/ Dynamic modes, also can be controlled intranet via RS232 and USB interface.
-
Product
Battery Load Tester
MD4260
-
Test capabilities: Battery voltage, battery cranking, battery charging volts and good/bad battery test. Test batteries on and off the car in just 30 seconds. Heavy duty copper-plated clamps. Internal loaded unit with a 100-amp load capacity. Load safety switch to prevent arcing. For 6- and 12-volt batteries.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 4.0 T Axle Load with 2 x 4 kW Drive Motors and Max. Track Width of 2,200mm
C_MBT C 4.0 W220 | VP 210156
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and Vans up to 4.0 t axle load with 2 x 4 kW drive motors and a max. track width of 2,200 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes with high vehicle throughput and increased loads.
-
Product
Battery Load Bank
-
Foresight Electronics Co., Ltd.
Utility is used for battery systems range from 21-30V, if higher current is needed, two or more FST-24V units can be linked together. Discharge to Battery string voltage as 24V, Cell voltage as 1.2V/2V/6V/12V adjustable stop points and multiple alarm designs to control the discharge process intelligently 7inch LCD touch screen for easy operation and showing various parameters real time Support RS232 real time monitoring by PC or SD Card download data after discharge
-
Product
Inductive Load Tester
4602-LV
-
There is a tendency that MOSFET has Low On Resistance so that it demands that Inductive Load Tester to have higher forcing current for measurement. The forcing current is limited by forcing voltage with previous test method. Thus it becomes difficult to test this kind of middle power range devices.
-
Product
Digital Roller Brake Tester for Cars and Vans up to 3.5 T Axle Load with 2 x 3 kW Drive Motors and Max. Track Width of 2,500mm
C_MBT C 3.5 W250 | VP 210153
-
Maschinenbau Haldenwang GmbH & Co. KG.
Digital roller brake tester for cars and vans up to 3.5 t axle load with 2 x 3 kW drive motors and a max. track width of 2,500 mm.Particularly suitable as stand-alone tester or as part of car reception and diagnostic test lanes for larger vehicles such as SUVs, off-roaders or vans.
-
Product
Odd Shape Assembly Cell
JOT
-
The reusability of the platform and feeders is close to 80%, allowing the platform to grow and adapt with future business needs. The same cell is easily expandable to automate over 20 different processes and configurable to versatile applications like screw insertion, soldering, laser marking, labeling and packaging.
-
Product
Oscilloscope, 350 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2354HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Load Tests
-
For the production and quality assurance of electric motors and electric drive systems, the use of flexible and customer-specific testing technology is required. Vogelsang & Benning supplies the same to the needs and the application of the customer.
-
Product
48V / 300 Amp Load
BD18-48P
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with 48V and 50V, (24 or 25 cells at 2V each), battery systems and is extremely cost effective.
-
Product
Saluki SEL7 Series Programmable DC Electronic Load (up to 6kW)
-
The new SEL7 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL7 series delivers high speed and high accuracy with a resolution of 0.1mV and 0.01mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL7 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.
-
Product
Load Modules
-
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
Product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
AC Load Bank (Resistive & Inductive)
K-1000 Resistive & Inductive
-
Kongter Test & Measurement Co., Limited
Kongter resistive & inductive AC load banks are used to simulate the motor loads or other electromagnetic devices working at their rated power factor. Many backup generators and turbines are rated at 0.7, 0.8 or 0.85 power factor and need to be commissioned at nameplate capacity using a combination of resistive and reactive load to fully qualify their operating capability. Using a resistive & reactive load bank enables comprehensive testing from a single unit.
-
Product
8 Way GPS / GNSS Signal Splitter Passive, 1-2 GHz, N Type, DC Block+200Ω Load 8 Ports
GPS802
-
INSTOCK Wireless Components, Inc
GPS L1 - L5, GLONASS, Galileo splitterLow Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA max on DC block portsTri Alloy N Type Female (Jack) 50 Ohm
-
Product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2204HD
Oscilloscope
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
Product
Diffusion Cell Testing
-
Teledyne LABS Phoenix™ Dry‐Heat Systems make diffusion‐cell testing faster, easier, and more economical. The Phoenix Systemincludes an advanced diffusion cell design. Options include the compact Phoenix DB-6 six‐cell manual sampling system and the Phoenix RDS automated sampling system capable of handling up to 24 diffusion cells at once.An important advantage of the Phoenix System is the speed with which receptor cell contents are homogenized. Visual testing with red dye placed on the surface of the media at the top of the sampling arm shows complete dispersion occurs within a few seconds.Explore the pages in this section to learn more and to configure your own system.
-
Product
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)
510180111
SIM Insert
Thermocouple, Insert, Receiver, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 310130113 Receiver, i2 MX, 22 Slot VTAC/SIM Insert, EMINot loaded. Thermocouple patchcords need to be purchased separately.
-
Product
PXI Mixed Configuration Relay Module - 1 Cell Populated
40-138-AA-BB-CC-DD (1 CELL)
Relay
The 40-138 2A Relay Module with 1 cell populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
AC Load Banks
-
Power House Manufacturing, Inc.
Hand carried AC load banks in any capacity to meet your load testing needs. Power House Manufacturing has developed the best ultra-compact and light-weight hand carried AC load banks. AC load banks with capacities unmatched in the industry.
-
Product
Electronic DC Load, 500V, 16A, 400W
LDH400 Series
-
Versatile solution for direct testing of dc power sources and PFCsConstant current, resistance, conductance and power modesWide voltage and current range, 10 to 500V and 0 to 16A400 watts continuous dissipation at 28°C (360W at 40°C)High resolution and accuracy for level settingBuilt-in transient generator with variable slewCurrent monitor output for waveform viewingVariable drop-out voltage for battery testingHigh resolution backlit graphic LCD with soft key controlAnalogue remote control of levels and TTL control of on/off and transient switchingFront and rear input terminalsLoad inputs rated to CAT II (300V)Full bus control via USB, RS232 and LXI compliant LAN interfacesGPIB Option
-
Product
0-600 Amp Variable Carbon Pile Load Tester
6039
-
• Test batteries up to 1200 CCA• Fine threaded shaft for fine adjustment• Temperature compensation chart• Easy to read digital voltmeter & ammeter combine with the versatility of a carbon pile load• Spring loaded to shut-off automatically• Unique curved discs to prevent hot spots• Tests all battery types• Made in USA of US and Global Components
-
Product
Partial Load Failure
PLF Device
-
The control device series “PLF” has been designed to monitor the partial and/ or total failure of the alternating current absorbed by loads driven by static switches and / or electromechanical relays.
-
Product
Load Stability Tester
TruMotion™ Acceleration
-
When transport vehicles accelerate, turn or brake, the resulting low-frequency accelerations can cause unit loads to shift. Due to both safety issues and potential product damage/waste, regulatory bodies are requiring testing that’s closer to reality – assuring safe and stable unit load integrity!
-
Product
LB-Series Digital AC Load Banks
-
The LB-Series AC Load Banks are designed for high power portable load testing of generators, UPS, and other critical AC power sources. Available models meet a range of voltages including but not limited to 208, 380, 440, and 480 VAC. Load power model options reach 1000 kW standard with other options available.
-
Product
High Power DC Electronic Load
34000C Series（6KW~24KW）
-
34000C Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.
-
Product
110V / 90 Amp Load
EL12-110M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 110V Rectifiers and Power Supplies with output Voltages in the range of 100V to 135V and is extremely cost effective.
-
Product
Variable Resistor Load Bank
REOLOAD 100
-
A variable resistor load-bank with fixed stages connected in parallel and switched in, as required, with an adjustable stage for fine trimming. Designed for testing equipment under load. 1000V (AC or DC). 250A and 2500
