Base Station
Radio receiver / transmitter serving as the hub.
-
Product
Base Station Antennas
-
Amphenol Procom delivers state-of-the-art Base Station Antenna products for both RF and mechanical constructions. Our innovative approach to product development offers the highest quality and our thorough testing protocol guarantees our Base station antennas are the most reliable on the market. We test all of our products performance against dust, water, wind load, temperature and lightning, and many more areas.
-
Product
Base Station Antennas
-
Fiberglass Collinear 118-960 MHz Omni Patterns - 500 Watts Standard connector is a recessed N-Female. 7-6 DIN available
-
Product
Base Station Emulator
SUTP 5018
-
Designed to create a custom cellular environment to serve testing and characterization needs. The combination of high power, real-time computing and the software defined radio platform enables this instrument to create your own cells for testing in a compact size and cost-efficient way.
-
Product
Cellular Base Station Factory Test Systems
-
*Factory Test System*Designed and Built by BCO*100% Functional Testing*Environmental Stress Screening Testing
-
Product
Cryogenic Probe Station
CryoPro
-
Materials Development Corporation
The MDC Model 441 Cryogenic Probe Station is a cost effective alternative to high-priced vacuum based cryogenic probe stations. With up to five probes available and sample diameters up to six inches, the MDC Cryogenic Probe Station allows for electrical measurements at temperatures near liquid nitrogen levels (77K).
-
Product
Femtocell and Application Testing
-
About the size of a home ADSL Router, a Femtocell (also known as an Access Point Base Station) is designed to allow 3G enabled devices (Phones, PDAs, Laptops) to connect to a carrier's core 3G network even where the carrier does not provide a signal themselves. It does this by bridging between the Wireless 3G devices and the carrier’s network using the Internet. Specifically, it will be connected to a Router (ADSL, Cable or other) already providing access to the Internet. Calls made and data services used on the 3G device are then sent to the carrier (and received from the carrier) over IP.
-
Product
Plane Wave Converter
PWC200
-
The R&S®PWC200 Plane Wave Converter is a bidirectional array of 156 wideband Vivaldi antennas placed in the radiating near field of the device under test (DUT). The phased antenna array can form planar waves inside a specified quiet zone within the radiating near field of the 5G massive MIMO base station for realtime radiated power and transceiver measurements (EVM, ACLR, SEM, etc.).
-
Product
Coaxial Components
-
Surge arrestors are designed to protect wireless base stations, switching centers and transmission lines fromthe damaging effects of extreme high voltage surges caused by lightning strikes. The RFS lightning protectiondevices are designed and tested to the most demanding specifications. They are rated to protect against bothdirect and indirect multiple strikes in the harshest environments imaginable. Their rugged construction utilizes solid metal housing, and superior plating, which results in outstanding system protection and operatingcontinuity.
-
Product
RF Solutions
-
ST offers wideband and multiband RF solutions for wireless communication infrastructure and RF equipment including GSM/3G/LTE base stations, microwave links, cable modems, satellite, broadcasting, instrumentation, security, defense and test equipment.
-
Product
Bi-Phase Modulators
-
PMI's line of Bi-Phase Modulators includes a comprehensive selection of different models which cover broad octave frequency bands ranging from 0.5 to 40 GHz. Bi-phase modulators take a TTL level digital bits stream that’s encoded onto the RF carrier using 2 Phase Shift Keying (2PSK) modulation, where the 2 phases are separated by 180º. This performance is desirable in communications systems, microwave radio, radar, high data rate test & measurement, serial data transmission, base station infrastructure, and other industrial and military applications.
-
Product
Day Camera Testing
-
CI Systems' CCD test stations are used to carry out all the necessary tests to verify and compare the quality of a CCD based camera. These stations are based on CI Systems' reflective collimators, Visible Radiation Sources, special targets and integrated software, to project standard patterns with known geometry and intensity to the Unit Under Test. As a result, these stations are turnkey solutions for the CCD camera testing needs.
-
Product
Force Protection
-
The Durham is a high-performance, highly-mobile and easy to emplace Medium Range Day/Night Wireless Surveillance System using a state of the art day camera and a cooled, highly sensitive 640x480 InSb Focal Plane Array thermal camera with 8X continuous optical zoom. The system is image stabilized and has automatic tracking of targets. Each system consists of a Base Station and one Remote Station which can be emplaced up to 5km away for wireless operation or within 500m for fiber optic operation. A single Base Station can monitor and control up to four (4) Remote Stations. The system is powered by a generator, batteries, solar (supplemental power), or vehicle power. Other options available are laser pointers, designators, and a vehicle integration kit.
-
Product
Outdoor Antennas
-
Pulse’s outdoor antennas offer industry leading reliability for building out base station systems and extending wireless network coverage. Our outdoor antenna products can be used across a series of applications covering VHF, UHF, 4G LTE/5G, WiFi and GNSS Frequencies. Our robust offering of outdoor antennas includes;*Directional Yagi*Radome Omni’s*Base Stations*Outdoor Infrastructure*Femtocell Antennas*Multiband Antennas
-
Product
Line Automation Equipment
5000 Series In-line Handler
-
The Circuit Check 5000 Series In-line Handler is an integrated inline solution that combines automation, fixturing and measurement hardware in addition to other in-line PCBA probe based test stations, while adding a standardized quick change fixture interface. The 5000 series in-line is a unified solution that is software and hardware agnostic, enabling adaptability to a variety of off-the-shelf lower cost ICT, flash and functional test software and hardware.
-
Product
GNSS Modular Receiver
R750
-
Save time, money and headaches with the Trimble R750 GNSS Modular Receiver, Trimble's reliable, easy-to-use base station solution. With remote monitoring and alerts, an internal radio, LTE modem and rover capability, the R750 is designed to meet all your needs.
-
Product
Co-Siting Filters and Combiners
-
*Multiplexers, Duplexers, Diplexers and Antenna Sharing Combiners*Enables multiple base stations to share a single antenna*Many of the units offer both High and Low band support*Ideal solutions for either ground based and tower based antenna sharing*Compact lightweight rugged construction
-
Product
High Power Switch and Bias Module
-
Macom Technology Solutions Holdings Inc.
MACOM’s High-Power Switch and Bias modules are extensively used in 4G and 5G TDD base stations as well as aerospace and defense applications. The PIN Diode Switch features high power handling, low insertion loss, and super board band performance. The integrated bias controller utilizes a boost circuit and provide the driver circuitry to the switch. The modules require only a single 5 V supply, and a single TX / RX control signal which greatly reduced the customer design complexity.
-
Product
PEM Fuel Cell
48 Volt 5kW
-
It is the aim of CellCare Technologies to continually introduce new technology that can provide significant benefits over existing solutions in specific applications. Fuel cellThe latest introduction to the product portfolio is a 5kW PEM (Proton Exchange Membrane) based hydrogen fuel cell, designed to replace 48V standby batteries within remote telecoms sites, satellite base stations, ISP base stations, uplink facilities and weather data collection sites. This technology provides instant power with no hazardous waste, zero emissions, extended autonomy and a guaranteed lifetime with minimal maintenance.
-
Product
Soil Testing Complex
GEOMehanika-M
-
The developed measuring complex for testing soils with "GEOMECHANIKA-M" stamps includes:Control and registration unit: measuring station based on NI cRIO equipment, MIDA overpressure sensor, wireless access point AWK-3131-EU-T, pneumatic system based on pneumatics CamozziLinear motion sensorsWireless Operator Console TestSet of connecting cables
-
Product
PIM Testing
-
Rosenberger Hochfrequenztechnik GmbH & Co. KG
Passive Intermodulation (PIM) is a non-linear response of two or more signals of different frequencies mixing together in a passive device, e.g., antenna, cable, con- nector or splitter. Today, PIM has become a very serious, and challenging issue for mobile operators, equipment vendors, and component manufacturers due to frequency planning in modern communication networks, the usage of high-power transmitters and the usage of more sensitive receivers in base stations. If a PIM with sufficient magnitude generated from a transmitter falls within an adjacent receiver channel, it causes serious interfe- rences to the base station receiver and will significantly degrade the network quality of service.
-
Product
Frequency Counter with Rubidium Timebase
SR625
-
Stanford Research Systems, Inc.
The SR625 Frequency Counter is a NIST traceable frequency counting standard for calibarating base stations, transmitters and many other types of communication systems.
-
Product
RF Shielded Test Enclosure, Largest Rack Mountable Enclosure
JRE 1724
-
Originally designed for testing wide screen laptops, the rack-mountable JRE1724 is ideal for large wireless devices such as; Mesh Network AP's, Cellular/LTE/4G Base Stations, and other large RF devices. Featuring rugged welded aluminum construction, you can be assured of its tight RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble free operation over its lifespan. Internal struts keep the lid open for easy internal access when connecting the device under test.
-
Product
LTE RF Communication Subsystem
-
The Delaire USA LTE RF Communication Subsystem is designed to provide a versatile solution for the testing needs of the next generation wireless systems. With the LTE test subsystem developers can build an end-to-end test environment for complete system operation. From end user equipment and eNodeB base stations to full system functionality, the LTE RF Communication subsystem allows developers to test and evaluate equipment and system performance in a controlled laboratory environment.
-
Product
Attenuation Control Unit, DC to 6 GHz, 0 to 121 dB, 1-dB Steps
J7201A
Attenuator
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
-
Product
Vector Tester
PVT360A
-
The R&S®PVT360A is a VSG/VSA single-box vector tester optimized for FR1 base station, small cell and RFcomponent testing in production and characterization environments. Two independent signal generatorsand analyzers enable fast parallelized measurements. A frequency range of up to 8 GHz, flexible bandwidth configuration and an optional second TRX channel provide the necessary performance and enable flexible adaptation in a small form factor.
-
Product
Digital Matrix Intercom System
Gemini
-
A system that interfaces with existing communication assets such as SIP telephones.A way to reduce costs for linking remote sites by using standard IP infrastructure.An intercom system that operates over LAN or WAN or Internet.Works on any terrestrial or satellite-based network.Virtual and hardware operator panels to configure and manage each unit.Private one-to-one, group and conference calls with the ability to manage simple to complex conference and private conversations simply and quickly.Interfaces for telephony, 4 wire, and other audio devices such as Radio base station or Presenter systems.Sophisticated SIP integration for modern telephony interconnection options.Camera Mix interfaces for 6 cameras to/from Engineering and Production.
-
Product
Vantage Pro2™ Plus Stations
6162 & 6162C
-
*Solar Powered Integrated Sensor SuiteThe wireless, rugged outdoor sensor suite runs on solar power. A lithium battery provides backup at night and during cloudy, winter days. The cabled version receives power from the base station.*TemperatureCurrent inside and outside temperature, and for each of the last 24 hours. High and low temperature alarms.*HumidityCurrent inside and outside humidity, and for each of the last 24 hours. High and low humidity alarms.
-
Product
Interconnect Products
-
Typical industrial applications for Oxley Interconnect products include high voltage power supplies, critical computer hard drives, fire safety control equipment, medical and pharmaceutical equipment, oil and gas control systems, power generation and distribution equipment, rail and telecommunications infrastructure. Within aerospace and military markets Oxley products are typically found in aircraft, military vehicles, ground base stations, surface ships and submarines and air and ground communications equipment.
-
Product
BDAs & Repeaters
-
*Bi-directional amplifiers designed for Nano, Pico and Femto base stations*The PCS and AWS configurations provide up to 10 dB of Uplink and 25 dB Downlink gain*Separate TX and RX inputs and a common antenna port with an optional full duplex input*Ideal for in-building and spot coverage applications
-
Product
Attenuation Control Unit, DC to 18 GHz, 0 to 121 dB, 1-dB Steps
J7201B
Attenuator
Designed for WLAN and WiMAX™ device manufacturing test and mobile handset base transceiver station (BTS) handover test.
