Partial Discharge Monitors
See Also: Partial Discharge, Partial Discharge Detection, PD, PD Test, Partial Discharge Test
-
product
Fiber Optic Type Chemical Solution Concentration Monitor
CS-100F1 Series
The CS-100F1 Series is equipped with fiber optics cable based on the CS-100 Series. It offers real-time, in-line measurements by directly integrating the sample cell into the cleaning system piping and by using a fiber optic cable for light signal transmission. A single concentration monitor can take up to four measurements and monitoring of multiple chemical solutions in a single-bath or single-wafer cleaning system is also possible.
-
product
Partial Discharge Test System
TPP
The Partial Discharge Test System type TPP is used for non-destructive insulation and quality testing of electrical components (for example according VDE 0110-1, EN 50178, IEC 60270 and IEC 60060).
-
product
PC Based Power Monitor
11P-Link
1P-LINK compact interface box is the choice for users who want to do all power meters control as well as the analysis from their computer. With its impressive features for statistics calculation and display options, the 11P-LINK is also an answer to scientific or OEM users who need a low-cost computer based power monitor
-
product
Voice Monitoring
VOIP Echo
*The Voice Band Analyzer (VBA) is an analysis tool for monitoring the quality of voice band traffic (including hybrid echo) over VoIP, TDM and wireless networks*VBA works in conjunction with GL's TDM, Packet, and Wireless non-intrusive capture products, such as T1 and E1 Call Capture and Analysis, VoIP PacketScan&trade, and GSM, CDMA, and 3G Call Capture Products. VBA instantly detects voice file captures and with appropriately installed analysis modules, monitors speech levels, noise levels, and hybrid echo. Other analysis modules such as ITU-T P.561, P.562, P.563, fax and modem analysis, and many others can be hosted as plug-ins.*The VBA application can also operate on pre-captured files. It supports A-Law, µ-Law, 16-bit PCM (Intel), 16-bit PCM (Motorola) and MS Wave file formats.*Required software PKV100 and VBA032 at each probe location and PKV170 PacketScanWEB - Network Surveillance Software*Required hardware - 1U rack PC with sufficient hard disk for capturing over 10,000 calls (80 GB HD) for each VBA colocated with a probe*Additional hardware - PC for PKV100 PacketScan™ Software
-
product
Multi-Channel Earth-Loss Monitor
The SURETECH Earth-Loss Monitor (ELM) measures the resistance to earth of cable armouring in such a way thatthe user can actually LOCATE the earth loss.
-
product
Photoacoustic Infrared Gas Monitor
Chemgard
The stable, durable Chemgard Photoacoustic Infrared Gas Monitor is purpose-built and detects minute amounts of a wide variety of gases. Three different enclosure styles ensure there is a configuration for wildly different situations.
-
product
Multi-Parameter Monitor / Controller
900 Series
Myron L® Company’s new 900 Series Multi-Parameter Monitor / Controllers combine Accuracy, Reliability, Simplicity, and Flexibility. The user intuitive GUI (Graphical User Interface) allows easy and complete programmability of the instrument all from the LCD touch screen. These highly accurate instruments have the ability for simultaneous monitoring and controlling of multiple inputs/outputs.
-
product
SparkFun Single Lead Heart Rate Monitor
AD8232
The AD8232 SparkFun Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart. This electrical activity can be charted as an ECG or Electrocardiogram and output as an analog reading. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op amp to help obtain a clear signal from the PR and QT Intervals easily.
-
product
Discharging Bars
VARIO discharge products consist of a separate AC power supply for connecting one or more Eltex discharging components. In SINGLE discharging, the voltage generation (power supply ) is integrated in the bar.
-
product
ESD CONTINUOUS DUAL OPERATOR WRIST STRAP MONITOR
This economical continuous wrist strap monitor ensures that your wrist strap is in good working condition. Ensure wrist strap in good working condition
-
product
Environmental Monitoring Modules
Unidata’s environmental monitoring modules are robust and easy to install, simple to use and require very little maintenance. Typical applications include temperature monitoring, solar radiation monitoring, wind speed and direction measurement, barometric pressure measurement, rainfall recording and many more.
-
product
Power Monitors
Analog Devices’ power monitoring amplifiers provide an integrated solution for digital current and voltage measurement via an on-chip, 12-bit analog-to-digital converter (ADC), communicated through an I2C interface. Leveraging ADI’s precision analog design techniques, ADI’s products are twice as precise as competing devices, offering best-in-class accuracy (<±0.8%). The power monitors complete the industry’s only monitor and sequencer family to deliver <±1% accuracy for 2 to 12 supplies.
-
product
Area Monitoring: Measuring Stations And Measuring Sytems
In everyday life, we are surrounded by electromagnetic fields (EMF) wherever we are. They come from power lines, electricity cables, cellular radio and cordless phones and many other things, too. To protect the general public, the limit values are checked regularly and sometimes monitored continuously. Narda offers various measuring stations and systems for this purpose.
-
product
Battery Monitoring System
IPQMS-C64
The iPQMS is the premier battery monitoring system in Eagle Eye's IBwatch-Series. It ensures backup power systems are optimally maintained in large-scale environments. The iPQMS is the main processing unit that measures up to 448 jars (or 448 cells) utilizing up to seven Relaying Units (RU). Each RU connects up to 64 jars (or 64 cells) and captures data from these batteries and sends it to the MPU in real-time. The iPQMS can be used over a private network via TCP/IP, or locally with RS-232. Networked systems can utilize SMS/Email alerts during an alarm outbreak. If you do not wish to use our Battery Management Software, Modbus protocol is available for third-party integration. Flexible expanding solutions allow multiple iPQMS units to monitor all your systems in real-time.
-
product
Real-Time Quality Monitoring For 4K
RTM 4K
4K or multi-channel HD with 12G-SDI Interfaces Optional 10G IP for ST 2110 Networks
-
product
Torque Measuring and Monitoring System
WISER 4000
TECAT Performance Systems, LLC
The WISER 4000 system is the latest release of TECAT’s low-cost, ultra-low power and extremely accurate torque sensor. The wireless system has the optional ability to measure 3-axis acceleration, barometric pressure and ambient temperature, all within the same incredibly small footprint. The 4000 includes on-board data logging without PC or DAQ connectivity, and remote flash capability, which enables firmware upgrades without removing the system from the unit under test. Featuring shunt calibration, TECAT’s latest WISER system is designed to simplify instrumentation verification for users, while allowing them to check calibration of the system in the field. In addition, the WISER 4000 has been enhanced with two additional outputs, a higher-speed recording, and is available with custom-built remote enclosures to protect the system’s remote unit and battery from damage due to debris.
-
product
Multi-Sensor Thermal Imaging Camera for Condition Monitoring
A310 PT
FLIR A310 pt thermal cameras can be installed almost anywhere to monitor the condition of your critical equipment and other valuable assets. Designed to help safeguard your plant and measure temperature differences, they allow you to see problems before they become costly failures -- preventing downtime and enhancing worker safety. FLIR A310 pt is ideal for various applications that require temperature measurement capabilities including: substation, transformer, waste bunker, and coal pile monitoring.
-
product
Intelligent Application and Service monitoring
Datadog
With turn-key integrations, Datadog seamlessly aggregates metrics and events across the full devops stack.*SaaS and Cloud providers*Automation tools*Monitoring and instrumentation*Source control and bug tracking*Databases and common server components*All listed integrations are supported by Datadog
-
product
Spectrum Monitoring and Interference Detection Software
Supports multiple users; Compartmentalization between profiles; Allows real-time monitoring and generates SMTP alarm traps; Displays a large number of carriers (100+) Numerous RF calculations and monitoring settings; Waterfall Display; Spectrogram Display; OCBW, ACPR, 3dB Bandwidth; Min/Max, Channel Power; Up Time Report; All Major Browsers Supported
-
product
Solution for Industrial Monitoring
PDScope
Techimp PDSCope is a brand new product of the PDCheck family particularly designed to suit all the requisites of the Techimp TiSCADA systems for on-line monitoring of diagnostic quantities in electrical assets.Techimp PDSCope is a powerful PD analyzer based on Techimp TF Map technology (patented) allowing preliminary noise rejection and automatic calculation of statistical parameters relevant to Partial Discharges.
-
product
Test Cell Vibration Monitoring System
The Test Cell Vibration Monitoring System is a complete package for monitoring dyno vibration levels generated during engine testing. This system was design to prevent catastrophic dyno failures.
-
product
Solution for Industrial Monitoring.
PDCheck
PDCheck is a compact, stand alone, global diagnostic system for the condition assessment of medium and high voltage electrical systems, based on the detection and analysis of PD
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Concrete Measuring and Monitoring System
IQM-Meter
Designed specifically for monitoring and analyzing fresh concrete, the IQM Module is programmed with the required Equivalent Age of the concrete under test. Once this preset maturity number is reached, a visual indicator will flash continuously, providing an effective, automatic indication that the concrete has reached the desired level of maturity.
-
product
Low Concentration Monitor- Sulfuric Acid/Hydrogen Peroxide
HF-700A
The HF-700A stabilizes hydrofluoric concentrations on the order of ppm in diluted sulfuric acid and hydrogen peroxide to enable continuous measurement and allow effective process management of the removal of the polymer residue following the etching process.
-
product
CMM AutoQAL & CMM Continuous Mercury Monitoring Systems
Continuous Mercury Monitoring systems, the CMM and CMM AutoQAL, are TÜV and MCERTS certified solutions for continuous mercury monitoring from hot, wet and corrosive gas streams of industrial processes, such as waste incineration, cement production and powerplants. Gasmet offers a full CMM solution package which consists of a system, lifetime service and support, documentation and training, and our expertise.
-
product
Universal Monitoring System
R&S®UMS400
The ever-increasing frequency range of wireless communications services calls for monitoring stations up to 8 GHz, in some cases even up to 20 GHz. Typically, this requires a monitoring sensor installed close to the antenna(s) in order to keep cable losses as low as possible for highest sensitivity. This is possible for both the R&S®UMS400 and R&S®CS-MC20, thanks to an outdoor housing.
-
product
Real-Time Monitor
PTR-QMS
The PTR-QMS series sensitivity is setting the industry's benchmark for more than a decade.
-
product
PC/104 Plus Watchdog Timer Status Monitor
P104-WDG-CSMA
This multifunction card contains a watchdog timer used to monitor the operation of your application program and operating system to initiate a system reset in case of a lockup. It can also monitor and control a variety of system hardware parameters. Three models with increasing features are available.
-
product
KVS Rugged Igniter Tester With Current Monitor
4314
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
