Programmable DC Electronic Loads
Vary load current programmaticlly.
-
Product
Partial Load Failure
PLF Device
-
The control device series “PLF” has been designed to monitor the partial and/ or total failure of the alternating current absorbed by loads driven by static switches and / or electromechanical relays.
-
Product
Resistive Load Banks
R Series
-
Load banks are devices which contain resistive, inductive and/or capacitive loads, apply the load to an electrical power source and dissipate the power of the electrical source. Portable and stationary resistive load banks incorporate as low as 1 kW load step increments for testing small to large generating sets. The fine control resolution ensures accurate load control and power factor targeting adjustments.
-
Product
24V / 400 Amp Load
EL12-24M
-
For Battery Discharge testing and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
Product
AC & DC Power Source
SPS-331
-
Kongter Test & Measurement Co., Limited
SPS-331 Support various tests including indicating meter, digital meter, energy meter, etc. At the same time, it output 2nd ~63rd harmonics.
-
Product
DC Voltage/Current Generators
-
Pulse generation/measurement with basic accuracy of ±0.02% and the minimum pulse width of 50μs, maximum output of 6V/5A
-
-
Product
Brush DC Drivers
-
Allegro provides a broad portfolio of safe and robust brush DC solutions. With both integrated and MOSFET gate drives our product lines are ideal for low- and high-power applications alike. Increased digital content with embedded drive algorithms simplify your implementation, while enhanced diagnostics and protection features ensure a safe and reliable solution.
-
Product
In-System Programmers
-
Xeltek in-system programming tools provide a convenient method for configuring microcontrollers and various serial devices. Users could simply program microcontrollers, Flash memories, PLDs, and FPGAs via the ISP cable. Devices are programmed in the target system or target hardware, making field applications more convenient than ever. Typically, a jumper/DIP switch enables in-system programming and a set of serial programming connector (such as an IDC connector) connects the target board(s) to the ISP programmer(s).
-
Product
Electronic Tensile Tester
QT-ETT
-
QT-ETT tensile testing equipments are specially designed considering tensile testing requirements for flexible materials that are commonly used in product packaging to study different properties of materials. This instrument utilizes Qualitest's latest embedded control system and operating software, with user-friendly operating interface and intelligent data management system.
-
Product
Electronic Resistance Store
MPS2
-
The MPS2 module is a mezzanine module designed to form DC resistance in two channels with a four-wire measurement circuit. MPS2 is installed on the mezzanine carrier - the NMU module and is connected to it via a local information highway. Up to four mezzanines of various types can be installed on the NMU module. The NMU module together with the mezzanines installed on it forms a VXI module of the size C-1 and is used to create information measuring VXI systems.
-
Product
Outdoor Permanent Mounted Load Bank
-
Mosebach Manufacturing Company
Mosebach Pad Mounted Load bank is designed to be permanently mounted next to a generator for dedicated testing. Its unique design allows it to be one of the smallest on the market! This size enclosure will fit 50 kW, 75 kW or 100kW of testing ability. Also available in 300kW and larger load banks.
-
Product
PXI/PXIe High Density Precision Resistor Module
42-297A-141
Precision Resistor Module
The 40-297A-141 (PXI) and the 42-297A-141 (PXIe) are 3-channel programmable resistors with a range of 2.5 Ω to 201 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
PC Programmable, Suitable For Pt100 Sensors
SEM206P
-
The SEM206/P is our entry level PC programmable temperature transmitter. It accepts Pt100 temperature sensors and converts the sensor output to a standard industrial (4 to 20) mA transmission signal.
-
Product
PXI Precision Resistor Module, 4-Channel, 2 to 6.97k
40-297-130
Programmable Resistor Module
This 4-channel PXI precision resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Programmable Insulation Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Electrical resistance testingLCD displayOutput Voltage: 1.0V~1000VThe insulation resistance range:100kohm to 100Gohm
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 1.5Ω to 1.81kΩ
40-251-122
Programmable Resistor Module
The 40-251-122 is a programmable resistor module with 2 channels which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Robotic Sample Loading Systems
-
Below you can see examples of two systems using our robotic sample loading system. Many other automated microscopy systems are possible using our components.
-
Product
DC Source/sink
-
Single channel system. One output with up to 1500 V or 1200 A. Maximum power in single operation 650 kW, up to 2.6 MW in parallel operation.
-
Product
Electronic Bypass Flow Meters
4912
-
Parker Conflow’s Code 4912 is an Intrinsically Safe electronic bypass flow meter that is designed for high flow, high pressure situations on mining roof support systems.
-
Product
Programmable ECU & CAN Gateway
MICROGen
-
MICROGen is a control prototyping hardware and software system. It has a range of uses, including as a communications gateway, during testing and for Rapid Control Prototyping.
-
Product
Spring Loaded Contacts
-
ATE Probes, Pogo pins and Contact Pads. Gold-plated, spring-loaded, capable of thousands of cycles. Probes for Automated Test Equipment (ATE). Various height SMT contact pins. Flat SMT contact pads. Spring loaded contacts consist of a plunger (or head), barrel (or body), and a fully encapsulated fine spring, to provide the spring force required to maintain positive contact. All have a high durability, exceeding 10,000 mating cycles.
-
Product
DC Overvoltage or Withstand Testing
-
Overvoltage protection is critical to the long-term health of any cable. DC overvoltage testing (also known as withstand testing) is the most popular method of general condition and integrity assessment in the power, industrial and domestic markets. This method of testing is distinguished a number of key advantages:
-
Product
Programmable Boards
LEO Board
-
LEO Board is a free programmable Aid for students who want to practice and enlarge their knowledge in programming of microcontrollers.
-
Product
Electronic Brake Meter Quarry & Plant Vehicles
BrakeCheck4Quarries
-
The BrakeCheck4Quarries is our portable brake tester designed specifically for quarry and plant vehicles (including mobile cranes). The Bowmonk BrakeCheck4Quarries is a fully self-contained, user-friendly, portable brake tester, suitable for quarries, coal sites, concrete plants, brickyards, recycling plants and HGV workshops. The instrument records the braking efficiency in a matter of minutes, and can optionally record the percentage of braking imbalance.
-
Product
AC Load Bank (Rack Mounted)
K-1000 Rack Mounted
-
Kongter Test & Measurement Co., Limited
Rack mounted resistive load bank is widely used in data center to simulate electric loads and dissipation of IT systems. These load banks are controlled by sectional steps with customized setting. Users could set power and time as per their needs with easy operation.
-
Product
VME System Electronics
-
Keysight VME electronics give the highest performance available in a laser interferometer system. Choose from a variety of axis and compensation boards.
-
Product
Battery Load Bank
K-3980
-
Kongter Test & Measurement Co., Limited
Kongter offers a series of customized DC load banks with many different models for constant current battery discharge test and battery capacity test. They cover a wide voltage range from 12V to 480V nominal voltages with current up to 600A. They are widely applied in various industries. With its optional battery Data Acquisition Case (DAC), discharge values of EACH cell could be monitored in battery load bank and PC software simultaneously by using Kongter’s data view software.
-
Product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
-
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Product
Control Electronics
-
Data acquisition and control electronics for optical radiation sources and measurement systems including precision current and voltage supplies for LEDs and tungsten halogen lamps.
-
Product
Universal Programmer Superpro 610p
-
Until now,Support 243 IC manufacturer, 33941 pcs devices and keeps growing.Support devices with Vcc from 1.2V to 5V.Extremely fast speed hign than SUPERPRO/500P.Built with 48 universal pin-drivers.PC hosted mode and stand-alone mode. Under PC hosted mode the programmer is controlled by a PC via USB2.0 (high speed) to program a chip.Only IC manufacturer approved programming algorithms are used for high reliability. (+5%~-5%) and (10%~-10%) Vcc verification enhances programming reliability.Advanced and powerful functions.Production mode start chip operation at the moment the chip is inserted in the socket properly.Project function simplifies processes such as device selection, file loading, device configuration setting, program option, and batch file setting into one touch step.Password can be set for project files and production volume controlBatch command combines device operations like program, verify, security into a single command at any sequence.Serial numbers generators are available as standard or customer-specific functions.Log file is useful for quality tracking.Over-current and over-voltage protection for safety of the chip and programmer hardware.WINDOWS XP/Vista compatibility/Win7/Win10
