Code
See Also: Programming, Scripts
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J03
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
Debug probe for ARM Cortex processors
USB Multilink ACP
-
P&E’s USB Multilink ACP is a debug probe which allows a PC/laptop access to JTAG/SWD on ARM Cortex devices from several manufacturers (see complete list below). It connects between a USB port on a Windows machine and the standard debug connector on the target. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included. By using the USB Multilink ACP, the user can take advantage of the debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
-
Product
8-Pin Power D-Type Cable, Male to Unterminated, Ferrules, 1m
A008PM5-F-5A100
-
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
Product
Cable Assembly, 25-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-025-1m-MU
-
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
Programmable Logic Units
-
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
Product
Tool
Imagix 4D
-
Imagix 4D is a tool to understand, document and improve complex, third party or legacy source code in C, C++ and Java. Imagix 4D automates the analysis of control flow and dependencies. It detects problems in data usage and task interactions. With Imagix 4D you increase productivity, improve quality, and reduce risk.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Tinned Ends, 1m
A015DF4-T-0A100
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 0.5m
A020GFR-C-0C050
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
NVIDIA® Jetson™ TX2-Based AI Smart Camera Starter Kit/Lite Kit
NEON-2000-JT2 Series Kit
-
- Integration of NVIDIA Jetson TX2, image sensor and vision software suites, ready to deploy- All-in-one design minimizes cabling, footprint and maintenance- FPGA base DI/O for accurate real-time triggering- Validated and comprehensive accessories, saves effort on surveying and debug- Pre-installed software and sample code, easy to get started- Two kit configurations to satisfy different applications
-
Product
SNMP & CLI Development
-
*Monitoring Windows and Linux Servers using secure SNMPv3*Windows and Linux SNMP SubAgent Development Tools*Embedded SNMPv3 and CLI Code Generators*Avionics AFDX / ARINC664 & SNMP*NTCIP Transportation SNMP
-
Product
Ada Embedded Software Test Solution
VectorCAST/Ada
-
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing Ada software components necessary for validating safety- and mission-critical embedded systems. VectorCAST/Ada parses your source code and invokes code generators to automatically create the test code (stubs and drivers) required to construct a complete, executable test harness.
-
Product
Cable 100-Pin Micro-D Male to Unterminated, Cut Ends, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9A200
-
This 2m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
Product
Pin Moisture Meter with Bluetooth®
FLIR MR55
-
The FLIR MR55 is a pin-based meter with wireless connectivity, which offers the convenience to view readings from a mobile device via the FLIR Tools® Mobile app. Thanks to a built-in library of 11 material groups, users can tune the meter to the appropriate test material to improve measurement accuracy. This library is easy to access on the FLIR.com website by scanning a QR code on the back of the meter with a mobile device.
-
Product
Node.js® platform
N|Solid™
-
N|Solid is a fully compatible Node.js runtime that has been enhanced to address the needs of the enterprise. Rapidly resolve performance problems. Protect customer data from vulnerable packages and unauthorized code. Drive performance and operational efficiency at scale.
-
Product
SparkFun 2D Barcode Scanner Breakout
-
The SparkFun 2D Barcode Scanner Breakout is a nifty little breakout board featuring the DE2120 barcode scanner module from DYScan. The DE2120 reads 20 different barcode symbologies (both 1D and 2D) using a camera coupled with on-board image processing to identify and decode everything from UPC codes to QR codes. The module also features two LEDs: one for illumination and one to project the red line that you're used to seeing from laser-based scanners.
-
Product
FCC Testing and Certification
-
Radiometrics Midwest Corporation
Radiometrics was one of the first labs in the country to receive acceptance by the FCC as an independent lab available for performing tests to the FCC Code of Federal Regulations.
-
Product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
-
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M8K1760Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.In addition, Checksum, SRQ bit and Header Words are supported on each channel, as well as, error injection (BC and RT modes) and error detection (all modes).Each M8K1760PxS single function module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The M8K1760Px(S) comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application
-
Product
MODBUS RTU Test Software
-
MODBUS RTU Communication Test Program that helps users troubleshoot MODBUS RTU Communications. The software supports function codes, #3, #6 and #10(hex)
-
Product
Video, Audio & Time Code Distribution Amplifiers
-
ESE has an extensive line of Distribution Amplifiers for both Video, Audio and Time Code. Our popular ES-207A is a small 1 x 4 video DA which can be tucked away anywhere. Other models have 1 x 8 and 1 x 12 capability. Rack-mount, PC card and "black box" configurations are available.
-
Product
Cable Assembly 15-Pin D-Type, Female to Unterminated With Ferrules, 1m
40-972-015-1m-FU
-
The 15-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Ferrules, 10A, 1m
A020GMR-F-0C100
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Tinned Ends, 2m, HV
A009DF4-T-HA200
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Sensor
Lepton
-
The FLIR Lepton™ is the most compact longwave infrared (LWIR) sensor available as an OEM product. It packs a resolution of 80 × 60 or 160x120 pixels into a camera body that is smaller than a dime. This revolutionary camera core is poised to equip a new generation of mobile and handheld devices, as well as small fixed-mount camera systems, with thermal imaging capabilities never seen before. Lepton contains a breakthrough lens fabricated in wafer form, along with a microbolometer focal plane array (FPA) and advanced thermal image processing. In order to support the lepton and make it easy to use, we have developed a breakout board to support the module along with example source code. Please see the Lepton Thermal Camera Breakout Datasheet for more information.
-
Product
Cable Assembly, 25-Pin D-Type, Female to Unterminated With Ferrules, 2m
40-972-025-2m-FU
-
The 25-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) Tinned Copper wire. The connector can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
GPU Servers
-
Advantech GPU powered rackmount servers that offer massive parallel computing power and unrivaled networking flexibility. It is designed to deliver ample processing power for the most computationally-intensive applications. GPU-accelerated computing takes advantage of the massive parallel architecture of graphics processing units (GPU) for compute-intensive tasks, while the rest of application code runs on the CPU.
-
Product
Cable Assembly, 9-Pin D-Type, Male to Unterminated With Tinned Ends, 2m, HV
A009DM5-T-HA200
-
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation.
-
Product
Trimmer Potentiometers
-
CTS trimmers are typically used in applications that do not need frequent adjustment and are often used for "set and forget" initial adjustments in circuits. These are usually located on the circuit board and out of view. CTS trimmers are available in a variety of standard resistance values, tolerances, power ratings, and mounting styles. Depending on product series, adjustment knobs are available with color coding and a screwdriver and/or hex hole for top or bottom side adjustments.
-
Product
PICMG 1.3 Full-size CPU Card With LGA1151 8th Gen Intel® Core™ I7/i5/i3, Xeon® E, Pentium® Or Celeron® Processor, Intel® C246/Q370/H310, SATA 3.0, USB 3.1 Gen1/Gen2, Dual LAN And DVI-I
SHB150
-
The SHB150 is based on the latest LGA1151 socket 8th generation Intel® Core™ processors (code name: Coffee Lake) and Intel® C246, Q370 or H310 chipset. The SHB150 features multiple I/O options and high-speed transfer interfaces as well as superior graphics capability (Intel® HD Graphics), making it an ideal solution for smart factory automation. The Intel® Core™-based full-size SBC, SHB150, comes with two 288-pin DDR4-2666/2400 Long-DIMM sockets with up to 32GB of system memory. The PICMG 1.3 single board computer has a maximum of six SATA-600 ports supporting software RAID 0/1/5/10 for data redundancy. It also has one M.2 Key M 2280 SSD slot with a PCIe x4 interface. The SHB150 with the Intel® HD Graphics brings a true high definition visual experience with triple display configurations (Intel® C246 or Q370) via DVI-I and DisplayPort (header) ports. Moreover, the Intel® Coffee Lake-based SHB150 supports optional Trusted Platform Module (TPM) 2.0 for optimum security, Intel® Active Management Technology (Intel® AMT) 12 for remote management, as well as Intel® vPro™ technology. The industrial single board computer provides significant advantages to customers in the fields of machine vision and industrial automation operations
-
Product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 10A, 2m
A020GFR-F-0C200
-
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
8-Pin Power D-Type Cable, Female to Unterminated, 0.5m
40-972-408-0.5m-FU
-
The 8-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
