Test Adapters
See Also: Interface Test Adapters
-
Product
Adapter Module, ITA, i2 MX, 2 Position
510108288
Adapter Module
Adapter Module, ITA, i2 MX, 2 Position.
-
Product
Configurable Functional Test System
ATS-5000
Test System
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
-
Product
Fixture Self-Test Controller and Calibration Check
AQ818
Test Fixture
The module AQ818 includes all the electronic blocks required to perform an effective test platform self-test. Thanks to this module, a chain of tests can be performed, which will end up not only with a report of the defective instruments or switch modules, but also with the relay contacts live expectancy report.
-
Product
Regenerative Battery Pack Test System
17020E
Test System
Charge/discharge modes (CC, CV, CP)Power Range: 10kW / 20kW per channelVoltage Range: 60V/ 100VCurrent Range: 100A/200A/300A/400A/ 500A/600A/700A/800A per channelRegenerative battery energy discharge, efficiency 85%Channels paralleled for higher currentsDriving cycle simulationFast current conversion without current interruptHigh precision measurementSmooth current without over shootTest data analysis functionData recovery protection (after power failure)Independent protection of multi-channel
-
Product
Electronics Testing Solutions
Test System
Don’t cut corners when it comes to developing high-quality electronics functional testing solutions. Ball Systems helps you ensure you deliver the quality your customers expect by providing open and reliable advanced technical testing solutions.
-
Product
Adapter, APC-7 to Type-N (f)
11524A
Contact Adapter (Receiver)
The Keysight 11524A is a general purpose grade, APC-7 to type-N female adapter.
-
Product
RSE Wireless EMC Spurious Emission
TS8996
Test System
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
Product
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509
510140113
Pull-Thru Adapter
Pull-Thru Adapter, Wired, QuadraPaddle, to 100 Pin ML SCSI, f/ NI PXI-6514/15, 6509.
-
Product
Automated Test Systems
Test System
WinSoft designs, develops and integrates automated functional test systems for use in aerospace, military, high tech and commercial applications
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
Test Workflow Standard
test
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
Product
PXIe Optical Test Modules
Test Module
Coherent Solutions’ expanding portfolio of PXIe optical test modules bring a wide range of new mixed-signal test capabilities to the PXI platform. The new modules offer seamless integration with PXI Platform and deliver reliable and repeatable results across a wide range of optical and mixed-signal test applications.
-
Product
Functional Test Fixtures
Functional Test
Forwessun’s Functional Test Fixtures are tailored to validate the performance of your electronic assemblies, ensuring each product meets critical quality and functional standards. With customisable designs and precision engineering, these fixtures support a range of testing needs—from checking connectivity and function to confirming performance under real-world conditions. Built to handle rigorous demands, Forwessun's solutions are ideal for industries requiring reliable and repeatable results. Whether for high-volume production or specialised testing, our fixtures provide robust, adaptable support to maintain efficiency and accuracy throughout the testing process. We also create, and work with Ingun to create fixtures using the Ingun kit.
-
Product
Functional Test Trainer System
QT65
Functional Test
Qmax Test Technologies Pvt. Ltd.
Functional Test Trainer system, is a test system which can perform various Power- On functional tests of digital devices(ssl/MSI/LSIs and analog devices in the out- circuit and in-E conditions. Unified Library of vast number of devices to effectively test devices in in-circuit as well as out of circuit conditions.
-
Product
Pull-Thru Adapter, PCB, QuadraPaddle, to 96 Pin FML DIN, f/ NI PXIe-4322
510140250
Pull-Thru Adapter
Pull-Thru Adapter, PCB, QuadraPaddle, to 96 Pin FML DIN, f/ NI PXIe-4322.
-
-
Product
NI-6581, 100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module
780565-01
Digital I/O Adapter
100 MHz, 54 Single-Ended-Channel Digital I/O Adapter Module for FlexRIO—The NI-6581 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO, creates a digital instrument for interfacing with 54 single-ended digital pins. You can use the NI-6581 to do real-time interfacing of standard protocols and implement customized protocols. The NI-6581 can operate sample digital waveforms at up to 100 MHz. It includes support for common transistor-to-transistor logic (TTL) voltage levels, or other voltage references can be sourced externally using a front panel connector.
-
Product
6TL23 Off-Line Seat Operation Base Test Platform
H71002300
Test Platform
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
Product
PXI Functional Test System
U8989A
Functional Test
The TS-8989 PXI functional test system is an integrated, all in one switch, load and measurement system in a box for high voltage or current mechatronics functional test applications of up to 104 nodes and 40A current loads.
-
Product
Electrification Testing Solutions
Test System
When looking for a partner to assist with your electrification testing or power electronics testing challenge, Ball Systems has the expertise and experience to ensure your energy storage or power conversion project moves forward efficiently.
-
Product
Modular Functional Testing Platform
OTP2
Test Platform
Functional testing is an important part of product development and manufacturing and is used to ensure quality, performance and reliability from launch to end of life. A modern, future-proof functional test system must meet many criteria in order to meet the ever-growing demands of the industry. The OTP 2 open test platform developed by LXinstruments meets the following requirements for a dynamic and highly competitive market.
-
Product
In-Line 2-Module In-Circuit Test System; i337x, Series 5i
E9988E
In-Circuit Test System
Short wire fixturing eliminates problems commonly found with long wire fixturing, such as noise and deterioration of test stability. This translates into transportable, repeatable and stable tests on your i3070 Series 5i, even if you need to deploy tests halfway across the globe, or on different manufacturing sites.
-
Product
VLSI Test Systems
Test System
50/100 MHz clock rate50/100 Mbps data rate1024 I/O pins (Max :1280 I/O pins)Up to 1024 sites Parallel testing32/64 M pattern memoryVarious VI sourceFlexible HW-architecture (Interchangeable I/O, VI, ADDA,)Real parallel trim/match functionTime & frequency measurement unit (TFMU)High-speed time measurement unit (HSTMU)AD/DA test optionSCAN test option (max 1G M/chain)ALPG test option for embedded memorySTDF tools supportTest program/pattern converter(J750, D10, V50, E320, SC312, V7, TRI-6020, ITS9K)User friendly windows 7 environmentCRAFT C/C++ programming languageSW (Software) same as 3380P & 3360P
-
Product
EV Power Components End of Line Test Platform
Test Platform
Test and Validate all EV Power Electronics with One Flexible and Scalable Solution
-
Product
ARINC-429 Module
M4K429RTx
Test Module
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
-
Product
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO
NI-6584 / 781290-02
Digital I/O Adapter
16 Mbit/s, 16-Channel Digital I/O Adapter Module for FlexRIO—The NI-6584 is a digital I/O adapter module that, when combined with a PXI FPGA Module for FlexRIO or the Controller for FlexRIO, creates a digital instrument for interfacing with 16 RX and TX pairs of RS485 or RS422. This digital I/O adapter module for FlexRIO can be used to do real-time interfacing and analysis of RS485 and RS422 as well as other electrically compatible interfaces. The NI-6584 can sample digital waveforms at up to 100 MHz clock rates, has terminated and unterminated options, and full and half duplex configurations.
-
Product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 100 Pin Female HDI
510140135
Pull-Thru Adapter
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 100 Pin Female HDI
-
Product
Coax, Contact, Receiver and ITA, 40 GHz
610102114
Contact Adapter (Receiver/ITA)
The 40 GHz Coax contact is a blind mate connector that mates with 3.5 mm and 2.92 mm connectors. It is recommended to use 2.92 mm connectors for frequencies above 35 GHz. The temperature range is -50°C to +125°C.Mechanical SpecificationsDurability 20,000 cyclesContact Material Passivated stainless steel bodyberyllium copper contactsAu platedContact Plating Au platedContact Termination 2.92mm compatibleInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC – 40 GHzVSWR 1.35 DC - 18 GHz1.55 18 - 40 GHzInsertion Loss ≤ -0.3 dB @ DC - 18 GHz≤ -1.5 dB @ 18 - 40 GHzCable Specifications 2.92 mm CompatibleEnvironmental SpecificationsOperating Temperature -50°C to +125°C
-
Product
Coaxial Adapter, 3.5 mm (m) to 3.5 mm (m), DC to 26.5 GHz
83059A
Contact Adapter (Receiver)
The Keysight 83059A instrument-grade 3.5-mm male coaxial adapter offers outstanding performance to 26.5 GHz. With SWR typically better than 1.05, this adapter is ideal for most connector saver and interconnect needs.
