-
Product
High Voltage Power Supplies
-
FuG high-voltage power supplies of all types except HYN are primary switched-mode power supplies with pulse width modulation . The rectified mains voltage is chopped into square pulses of constant frequency, transformed, rectified and smoothed. The square-wave voltage is pulse-width modulated for regulation.
-
Product
Regenerative AC load function
61800 Series Optional Function
-
The regenerative AC load function consists of various modes such as CC Rectified mode, CP Rectified mode, CR mode, CC Phase lead/lag mode and CP Phase lead/ lag mode. The Rectified Mode is capable of simulating non-linear rectified loads with characteristics similar to Chroma 63800 series AC load where the voltage and current operate at the 1st and 3rd quadrant. The Rectified Mode supports both CC and CP functions with current, power and CF as parameter settings.
-
Product
Delta DC Rectifier Repair/Refurbishment
-
Delta DC Rectifiers are used by original equipment manufacturers to build On-Site Sodium Hypochlorite Generator Systems. These power supplies are generally operated at full load for 24/7 operations at high temperatures. Hence, these power supplies must be extremely rugged and must be de-rated significantly to achieve long operating life.
-
Product
AC Filament Switching and Line Relays
-
*Heavy duty Elkonite contact tips*AC and DC versions available*AC versions available with or without internal rectifier PCB*Automated vision system and operator inspection*Comprehensive automated end of line testing*Test Certificates supplied with each relay*Certificate of Conformity supplied with each order*Recertification and repair services available
-
Product
P Series Panel Meters
ST-38N
-
Standard Electric Works Co., Ltd
● DC up to 15A● Case and Composition: Acrylic resin front. ABS case. Four studs mounting. Two studs mounting.● Accuracy :DC : Class 2.0 AC : Class 2.5 Rectifier : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
48V / 250 Amp Load
EL15-48M
-
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 48V Rectifiers and Power Supplies with output Voltages in the range of 38V to 60V and is extremely cost effective.
-
Product
AC/DC Power Supplies
-
At ABSOPULSE Electronics, we specialize in the design and manufacture of heavy-duty custom and semi-custom AC-DC switching power supplies, rectifiers and battery chargers.We can meet any AC to DC input/output configuration requirement, with output power ranging from a few watts to several kilowatts.ABSOPULSE's rugged power supplies are typically designed and built for an operational life of 20 to 30 years in harsh environments.
-
Product
M Series Panel Meters
ST-150T
-
Standard Electric Works Co., Ltd
● M Series all up to 15A● Case and Composition：Acrylic resin front and ABS resin case. Four studs mounting.● Accuracy：Moving coil type : Class 2.0 Rectifier type : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
Schottky Mixer And Detector Diodes
-
Majority carrier diodes formed by plating a layer of metal on a layer of doped semiconductor, which forms a rectifying junction.
-
Product
M Series Panel Meters
ST-118T
-
Standard Electric Works Co., Ltd
● M Series all up to 15A● Case and Composition：Acrylic resin front and ABS resin case. Four studs mounting.● Accuracy：Moving coil type : Class 2.0 Rectifier type : Class 2.0● Color：Black case, white scale plate.● Pointer：Tube type, color in black or red.
-
Product
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger
SD750100G
-
Zhejiang Sandi Electric Co., Ltd
40kw High Efficiency AC/DC Power Supply Charger 100-750VDC Charging Rectifier 100A Battery Charger is for DC battery system charging station. With three-phase non neutral conductor AC input, it has the advantages of high efficiency, high power density and low harmonic. 50-500Vdc output voltage range optional, suitable for all types of batteries.
-
Product
DC Filter Inductors
-
Osborne DC filter inductors (aka filter chokes) are commonly used in AC to DC conversion circuits to present an inductive voltage drop to the AC component of rectified current. This inductive voltage drop acts as a filter. Osborne designs filter inductors to components to function effectively (without saturation) in the presence of the DC current. Osborne will work with you to mitigate the impact of ripple frequency in conversion circuits. Every Osborne DC filter choke is designed for high performance with special consideration given to your circuit´s power supply frequency and conversion configuration.
-
Product
5000 AMP DC Rectifier - Air Cooled, P/N 6037C1
-
Air Cooled SCR Controlled Power Supply, 50 KW, P/N 6037C1Input: 480 VAC, 60 Amps, 3 PH, 60 HzOutput: 6 to 10 VDC, 5000 Amps maxContactor and overload relay are installed for protectionStart / Stop capabilityEPO capabilityManual voltage control and current limitOutput voltage and current are displayed on the voltmeter and ammeterIndoor enclosure, 68″H x 65″W x 36″DAll input/output connections are inside the enclosuresEstimated weight: 1000 lbs.
-
-
Product
Roughness Tester
-
Compatible with four standards of site to measure surface roughness ofvarious machinery-processed parts, calculate corresponding and clearly display allmeasurement parameters. When measuring the roughness of a surface, the sensor is placed on the surface and then uniformly slides along the surface by driving the mechanism by the sharp built-in probe. This roughness causes displacement of the probe which results in change of inductive amount of induction coils so as to generate analogue signal, which is in proportion to the surface roughness at output end of phase-sensitive rectifier.
-
Product
Device Thermal Test Systems
-
Thermal Engineering Associates, Inc.
Thermal test system combines the test and measurement capability of dedicated instruments with the ease of operation and data collecting capability offered by graphical-user-interface-driven software operating on an integrated computer.Diodes (PN, Schottky, LED, varactor, PIN), Stacked Diodes (Hi-V Rectifiers & LEDs), Laser Diodes, Transistors (Bipolar, MOSFET, IGBT) & Diodes, Integrated Circuits (Application & Thermal Test Die).
-
Product
AC Ammeters And Voltmeters With A MuP Type Rectifier
-
*AC Ammeters and voltmeters with rectifier type MuP 40,80,210,220,230*Handle deflection 85 ° type MuP40, MP 80*Handle deflection of 100 ° type MuP210, MuP 220 / 220T, MuP 230 / 230T*The technical data catalog can be found on the download tab below the product.
-
Product
S Series Panel Meter
ST-670B
-
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 30A● Case and Composition: Acrylic resin front and Bakelite case. Four studs mounting.● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate.● Pointer：Tube or knife-type, color in black or red.
-
Product
Diode Tester
FEC VF40CM
-
Frothingham Electronics Corporation
The VF40CM is intended for testing VF, HALF CYCLE SURGE, and THERMAL RESPONSE/RESISTANCE on small- and medium-power diodes and rectifiers. It can also measure THERMAL RESPONSE/RESISTANCE on NPN and PNP bipolar transistors using an external user-supplied VCB supply.The VF40CM also is sometimes used to measure VZ of low-voltage zener diodes up to the compliance voltage limit of the tester. 20V at 20A is possible.
-
Product
Substation Equipment Test Van
ETL-250
-
Apart from insulation withstand testing with DC (rectified) voltage up to 60 kV and ability to measure very small leakage currents, the system can be used for testing various objects with small electrical capacitance with AC voltage of up to 250 kV and measuring dielectric dissipation factor (Tan Delta) at industrial frequency.
-
Product
Rotating Electrical
-
Through its vast distribution network, WAI provides customers in the aftermarket with access to a wide range of product lines they need, when they need them. WAI’s production team is committed to consistently being the First-to-Market with the latest model products. This commitment, paired with the skill and expertise of the team, results in the introduction of more than 500 new products to the aftermarket each year. WAI offers 100 percent new alternators and starters as well as generators, motors, voltage regulators, rectifiers and other components for the Rotating Electrical market.
-
Product
AC-DC Rectifier / Converters
DC Converter
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
Product
Hall Effect Proximity Switches/Sensors
-
ChenYang Technologies GmbH & Co. KG
A Hall Effect proximity switch is a non-contact electronic switch, which consist of a permanent magnet or ferromagnetic part as trigger intermediary and a Hall Effect sensor IC. The Hall sensor IC detects the change of the magnet field when the permanent magnet comes in the close proximity to it and generates an electric signal. This signal is amplified and rectified to control the output signal of the switch.
-
Product
AC and DC Electronic load
63800 series
-
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
Product
Portable System for High-Voltage Solid Dielectrics Testing
HVT-70/50
-
Portable system HVT-70/50 is designed for carrying out high-voltage withstand testing of cable insulation and other solid dielectrics with DC (rectified) voltage up to 70 kV and AC voltage up to 50 kV RMS at industrial frequency (f = 50 Hz).
-
Product
Cable Test Van
ETL-35
-
ETL-35 is a cable test van designed for testing electrical substation equipment.Apart from cable insulation withstand testing with DC (rectified) voltage up to 60 kV and ability to measure very small leakage currents, the system can be used for testing various objects with small electrical capacitance with AC voltage of up to 100 kV and measuring dielectric dissipation factor (Tan Delta) at industrial frequency.
-
Product
Load Banks
EL08 Series
-
*Rectifier Test 8kW*All of our Load Banks are continuously rated for Power and Current.
-
Product
S Series Panel Meter
ST-670
-
Standard Electric Works Co., Ltd
● DC up to 50A● AC up to 30A● Hz Meter : Measuring Ranges : 45~55 Hz, 45~65 Hz, 55~65 Hz Rated Voltage : 110V, 220V Accuracy : Class 2.0● Case and Composition: Acrylic resin front and Bakelite case. Four studs mounting.● Accuracy : Moving coil type：Class 2.0 Moving lron type：Class 2.5 Rectifier : Class 2.0● Color：Black case. white scale plate..● Pointer：Tube or knife-type, color in black or red.
-
Product
Floor Conductivity Tester Hand Crank
LA-1 HC
-
LA-1 HC Floor Conductivity Tester Hand Crank is an easy-to-use meter developed for accurately testing the conductivity of floors and equipment. The LA- 1 must be used regularly to monitor proper conductivity with NFPA code # 99. Regular use of the LA-1 will establish and maintain procedures for the proper maintenance of conductive floors, eliminate fire hazards, and provide a static free environment. A hand crank AC type generator provides a rectified DC test potential. Additionally, there are no brushes to wear out. The LA-1 has an easy-to-read scale that is selectively expanded electronically to assure accurate readings over the entire range of the instrument and the scale has a length of 3.75. This is 42% longer than typical competitive testers. The LA-1 uses 500V DC to test the resistance (in ohms) between two points. (NFPA Code #99) The meter comes ready-to-use (tin foil must be applied to bottom of weights). Simply follow the instructions for use and instantly obtain an accurate measurement. Choose electric or hand powered model.
-
Product
Thickness Gauges
CMX DL+
-
The CMX DL+ has all the features of the CMX DL, plus a full featured A-Scan presentation with RF and Rectified viewing options. The CMX DL+ is equipped with 3 fully adjustable gates (start, stop, width, & Threshold). Equipped with a 20dB boost/cut attenuator, which offers added flexibility for transducer types and applications. Selectable 50 volt pulser boost or cut (100 200 volts). Truly the Cadillac of the CMX series.
