Thermal Test
Designed to produce a temperature change in a device. The magnitude and rate of this change should induce a sufficient thermal stress fatigue to identify sources of potential failure without causing catastrophic failure of all components. (sigmasystems.com)
See Also: Thermal, Thermal Shock
-
Product
Bypass Diode Thermal Test System
-
King Design Industrial Co., Ltd.
* Power: the heating board control panel uses 220V single-phase power.* Power consumption: 1.0KVA, 1000W(Max)* Volt: 220VAC* Current: 4.5A* Heating board: one controller per board* Power rate: room temperature raise to 75°C± 5°C within one minute.* Heating board dimension: 500mm x 1,000mm* 6-sheet electrical heating boards test: used to test the 2,200mm x 2,600mm module. It can be customer-designed.* The length of board power cable and thermal sensor cable shall exceed 3,000mm.* To get uniform heating effect, the electrical board is sandwiched by 2mm aluminum sheets at both sides of board.
-
Product
Thermal Test Boards
-
Thermal Engineering Associates, Inc.
TEA offers a series of thermal test boards for package characterization and design comparison that conform to to the JEDEC JESD51 standards. The board family, referred to as the TTB-1000 series, consists of two different standard sizes designed to cover a wide range of package sizes. These boards, also referred to as test coupons, provide a well defined mounting environment, will withstand temperatures to 125 oC, and have lead lands terminated in eyelets to allow for hand-wired connection to the board edge contacts. The board mates with a dual 18-pin, 3.962 mm (0.156") pitch edge-card connector.
-
Product
Thermal Runaway Test Machine
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Thermal runaway test machine test the whole vehicle or the complete vehicle-borne ion battery system or the subsystem of vehicle-borne lithium-ion battery system, including a lithium ion battery and an electrically connected lithium ion battery. The applicable standard is UL 2580, IEC 62619.
-
Product
IEC60884 Fig38 Thermal Compression Test Device For Plug Testing
IEC60884 fig38
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
Product
Thermal Shock Test Chamber
-
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
-
Product
Thermal imagers
-
Thermal imagers sensitive in MWIR and LWIR spectral bands are one of crucial surveillance technologies for defense/security sector. These imagers have also found mass applications outside defense sector. Testing thermal imagers is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of these expensive imagers.
-
Product
Thermal Controlled Chucks & Plates
TOP Cool
-
Mechanical Devices newest innovation in thermal testing. Each TP system contains a thermal chuck or thermal plate and a self-contained thermal control unit.The TP chuck and platforms is a breakthrough product that introduced the use of refrigerant for active cooling & heating of wafers and other components with no need of chiller, CDA, or consumable and expensive refrigerants such as liquid nitrogen and liquid carbon dioxide. It can be a perfect replacement system in the industry for uncompromising thermal and mechanical performance with a temperature ranging from -60 to +220°C.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
LifeTest Software
-
In combination with the extended range of PEC test equipment, LifeTest supports the many specific functionalities required in battery testing labs. Drive cycle simulations (FUDS, DST…), thermal performance tests, high speed pulse tests (HPPT), life cycle tests, accelerated ageing tests and internal resistance measurement tests can be easily configured, scheduled, executed and reported from a single platform.
-
Product
Digital Closed Loop Control Thermal and Mechanical Testing System
3800 System
-
The Gleeble 3800 is a fully integrated digital closed loop control thermal and mechanical testing system. Easy-to-use Windows based computer software, combined with an array of powerful processors, provides an extremely user-friendly interface to create, run and analyze data from thermal-mechanical tests and physical simulation programs.The result is a system unequaled for physical simulation and thermal-mechanical materials testing.
-
Product
IR FPA sensors
-
IR FPA sensors are the most important modules of thermal imagers. Design of sensor electronics (camera core) is a crucial part of designing of new thermal imager. Knowledge of precise parameters of IR FPA sensor is needed by both professionals involved in both IR FPA technology/thermal imagers technology because parameters of IR FPA sensors determine performance limits of thermal imagers. Therefore test equipment that enable measurement of IR FPA sensors is a vital tool for development of both IR FPA technology/thermal imagers technology. It is commonly known that data sheets provided by manufacturers of IR FPA sensors (both cooled or non-cooled) provide too little details for electronics designers. Sometimes the provided data is not accurate enough and better sensor performance can be achieved using modified control signals. Therefore design teams loose sometimes years to develop electronic camera core optimized for a specific IR FPA sensor. When the type of the IR FPA sensor is changed the whole process is to be repeated. In this situation an universal, flexible camera core that would accept IR FPA sensors from different manufacturers and to carry out semi-automatic determination of optimal signal controls for a specific IR FPA sensor would be highly desirable.
-
Product
Semiconductor Package Wind Tunnel
WT-100
-
Thermal Engineering Associates, Inc.
The WT-100 Forced Convection (Moving Air) Wind Tunnel is designed in accordance with the EIA/JEDEC JESD51-6 standard for thermal characterization of semiconductor packages and devices. The vertical design minimizes laboratory floor space requiements. Air is drawn in at the bottom and exhausts at the top. The test section is large enough to accommodate the largest JEDEC and SEMI thermal test boards. Air velocity can be adjusted over the range of 0.5 to 5 m/s; air velocity is monitored with an included hot-wire anemometer connected to a digital display. A Type-T thermocouple is mounted in the test section for monitoring the moving air temperature.
-
Product
Thermal Abuse Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's Thermal abuse test chamber is suitable for standard IEC 62133-2017, UL 1642 and GB 31241-2014.
-
Product
Relay Test Equipment
-
Vanguard Instruments Company, Inc.
The VIC Model PCI-600 is a programmable, high-current source that is designed specifically for utility-substation applications. This alternating current(ac) test device is used primarily for injection testing of protective relays. This same device can also be used for testing thermal, magnetic and solid-state motor-protection relays and molded-case circuit breakers. The PCI-600 is versatile and can also be used in many other applications that require a high-current source.
-
Product
Battery Test Equipment
-
Shenzhen Bonad Instrument Co., Ltd.
The tests that can be performed by lithium-ion battery safety testing equipment include temperature cycling test, thermal abuse test, high altitude low-pressure simulation test, vibration test, shock test, external short-circuit test, forced internal short-circuit test, drop test, crush test, impact test, nail penetration test, burning test, etc. These test items mainly apply to various lithium-ion cells such as 18650 cells and prismatic cells, lithium-ion batteries, lithium-ion battery modules, lithium-ion battery packs, and so on.BONAD battery safety testing equipment complies with various standards such as IEC 62133, IEC 62133, UL 2580, UN 38.3, UL 1642, etc. For more information, please contact us, BONAD will provide you with professional technical consultation and high-quality testing equipment.
-
Product
Thermal Testing
-
A view of multiple testing stations for use in conducting Thermal Analysis on various materials. This is one of several areas assigned to various thermal tests. Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA), Thermomechanical Analysis (TMA), and Dynamic Mechanical Analysis (DMA)
-
Product
Temperature/Humidity Vibration Test Systems
EHVC SERIES
-
The EHVC Series is designed for highly accelerated life testing, the demand of which from customers is increasing today. This is a joint system of the AGREE chamber and thermal shock chamber that we have manufactured and makes the temperature rate up to 20℃/min feasible with a compressor only. With this feature, the highly accelerated life test such as AGREE tests, most thermal shock tests can be performed with one unit.
-
Product
Standard And Custom Targets
-
Santa Barbara Infrared manufactures a wide range of targets for visible, and infrared/FLIR electro-optical testing. These targets complement our complete line of Visible and IR test products. Our targets are designed to function with one of SBIR’s target wheels. Utilizing a variety of manufacturing techniques, including conventional machining, photochemical etching, electro-deposition, electrical discharge machining (EDM) and laser cutting. SBIR targets are manufactured to exacting mechanical tolerances. SBIR manufactures all of the targets specified by MIL-STD-1859 and the Tri-Service Guide for thermal imager testing.
-
Product
Pyroelectric and Thermal Testing
-
The optional Chamber Task measures the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled within a thermal chamber, on a hot chuck or in a furnace. From these measurements the Spontaneous Polarization Pr(q) and the Dielectric Constant er(q) are computed. These are then combined to determine the Electrical Displacement D(q) as a function of the temperature q.
-
Product
Temperature Forcing System
-
Wewon Environmental Chambers Co, Ltd.
Wewon Technology specializes in the research, development, production and sales of laboratory testing equipment system services. Through more than ten years of accumulation in the field of equipment, the business of wewon Tech is mainly divided into three fields, namely optical communication, automobile and new energy industry.Specialized equipment from Wewon Environmental Chambers Co., Ltd. includes thermal stream instrument, environmental chambers, walk in chamber, salt fog test chamber, vibration testing machine, xenon lamp aging tester, ultraviolet weather testing equipment, tensile testing machine and various IP protection level test equipment. The system characteristic of Wewon Tech thermal stream temperature test system as below technical parameters mentioned.https://www.wewontech.com/temperature-forcing-system/
-
Product
Test Equipment For IEC 62133
-
designed for the battery thermal abuse test for IEC62133-8.2.2. The fire-proof dual-chamber has dimension 10" x 10" x 8", which can be heated up to 180°C via an independent temperature controller with +/- 1°C accuracy.
-
Product
Thermal Shock Test Chamber (3 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Divided into a high-temperature zone, low-temperature zone, and test zone. The test product is placed in the test zone, and the temperature from the high-temperature zone or low-temperature zone is applied to the test zone for thermal shock. The test product remains static during the test.- Equiped with a touch-screen control interface for easy operation.- Temperature is transferred to the test zone using a wind route switching method to perform thermal shock testing.- The maximum duration of high-temperature or low-temperature shock can reach 999 hours, and the maximum cycle period can reach 9999 cycles.- The system can operate in automatic cycle mode or manually select specific shocks. It can be set to perform two-zone or three-zone shocks, as well as cold-to-hot or hot-to-cold transitions.- The cooling system utilizes a dual refrigeration system, providing fast cooling. Water cooling is employed as the cooling method.- Testing can be performed at room temperature.
-
Product
Temp Characterized CalPod, 20 GHz
85531B
-
CalPods provide a new and unique way to quickly and easily refresh a network analyzer calibration, at the push of a button and without removing the DUT or re-connecting standards. Very useful in thermal chamber testing, where it is desired to remove the thermal effects of the test cables and connectors from the DUT’s response, and where it is impractical to stop the thermal testing to perform a normal re-calibration.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Environmental Testing
-
Environmental testing capabilities include: High and Low Temperature Testing including Thermal Shock. Humidity Testing to 100% Relative Humidity at High and Low Temperatures. Altitude Testing to 100,000 Feet. Combined Vibration, Temperature and Altitude Testing. Mass Spectrometer for Leak Testing. Vibration Testing to 50 G's and 3000 Hz including Resonance Scan, Cycling, and Endurance. Free Fall Half Sine Wave Mechanical Shock Testing to 100 G's
-
Product
Explosion Proof UV Inspection Light
-
he Labino MB Hercules Ex is an extremely durable product specifically developed for use in areas where the risk of an explosion is high. Offshore Oil Rigs, Refineries, Aerospace, and Defense often require explosion proof products to ensure safety for their inspection teams. The Midbeam Hercules Ex has successfully completed extremely tough tests, including tests for thermal conditioning, Impact Tests, Drop Tests and IP tests that led to the ATEX certification (Certificate: ITS17ATEX402144X). This unique product is suitable for use in extreme weather conditions varying from 104° Fahrenheit (+ 40° Celsius) to minus 4° Fahrenheit (- 20° Celsius).
-
Product
Thermal Shroud
BC8-55/150C
-
When combined with a thermal conditioner such as the Bemco PCL3L-III or PCL3M-III, this shroud converts a 24 inch inside diameter by 30 inch high vacuum only vertical bell jar into a 19 inch inside diameter by 20 inch high thermal vacuum testing system. With a convenient clam shell door, test objects are easily loaded by simply raising the bell jar above the top of the door opening.
-
Product
Environmental Test Chamber
-
High and Low Temperature Test Chambers, ESS Environment Stress Screening, 2 Zone Thermal Shock Test Chamber, 3 Zone Thermal Shock Chambers, Walk-In Chambers, Burn-in Room and Aging Test Chambers, Altitude Chambers, Industrial Drying Oven, Salt Spray Test Chambers, Temperature Humidity Vibration Comprehensive Test Chamber, Test Machine Series, Custom Made Environmental Test Equipment, Double-Layer High and Low Temperature Chamber, Explosion Proof Temperature Chamber For Power Battery, etc.
-
Product
Targets
-
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Product
Thermal Vacuum Data Acquisition and Control Software
TVAC 7000
Data Acquisition Module
Equipment used in space applications needs to go through stringent environmental tests in order to prove that it can survive the extreme conditions experienced during launch and while in space. Some of the key environmental tests include vibration, thermal vacuum, and electromagnetic compatibility. Thermal vacuum test is crucial to confirm the equipment is able to operate under the space vacuum condition.
