-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
Portable Telemetry Systems
-
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
Product
Infraded Temperature Transmitter
Model KM 6816-4 / KM 6816-5
-
Kusam Electrical Industries Limited
With CE approval and protection against electromagnetic disturbance for EU standard
-
Product
L-Series Kit
ZS-LRHMa
-
The L Series units all share a wide tuning range of three standard Lectrosonics blocks, or 67.5 to 76.8 MHz, depending on the specific frequency band, and employ Lectrosonics' patented Digital Hybrid Wireless® technology for compandor-free audio along with compatibility modes for interoperability with older analog systems. Like all our other products, the L Series units are made in the USA and feature machined aluminum housings, user-friendly setup and reliable operation. The ZS-LRHMa kit makes it easy to put these products right to work on the job. Everything you need is here: transmitter, receiver, mounting hardware and connecting cables. Even batteries are included! Check with your Lectrosonics dealer for pricing and availability.
-
Product
CrystalCalHP Calibration System
-
AMETEK Sensors, Test & Calibration
This portable gauge and transmitter calibration system is 7 to 10 times faster than a deadweight tester. It allows you to do a 10 point up and down calibration in less than 3 minutes including printing out a calibration certificate.
-
Product
Colorimeter Logger Sensor
NUL-219
-
The colorimeter measures transmittance and absorbance of red, orange, green and blue light components projected on a solution. The colorimeter logger sensor has an opening for a special square solution cuvette. It turns on four different lights in known values and measures the received light that passes through the solution.
-
Product
AS 857 AUTO SWITCHING TRANSMITTER
-
- Auto Switching to Secondary Input if Primary Signal Fail/Drops below -6dBm- Switches back to Primary Input when Primary Signal Reconnect/Improves above -4dBm- Input Signal Display of Active Input- AGC for both Input
-
Product
DM 150-Watt Transmitter
Loc-150Tx
-
The Loc-150Tx, 150-Watt DM Transmitter is used primarily with the Defect Mapper (DM) Receiver, however it is also useful for those needing a low frequency, high output transmitter. Typically, the Loc-150Tx, transmitter (DM transmitter) is used to apply a signal current to the anode bed. The pipeline returns the signal via coating faults back to the transmitter. The Loc-150Tx transmitter is designed to be powered from CP (Cathodic Protection) stations, AC or external batteries, eliminating the need for internal batteries. This transmitter has a direct connection mode to apply the locate frequency onto the conductor. There is no clamp or induction mode.
-
Product
Standalone ILINK Transmitter And Receiver
SPC-ILINK
-
SPC-ILINK, a standalone accessory for SPC-800 monitors, uses HDBase-T for long-range video and USB control, supporting 100m video with 4K/8K ESD.
-
Product
MPU- Passive Sensors
-
sensors of the MPU series are passive elements intended for measuring rotational speeds or speeds of moving parts. The measuring principle is based on voltage induction in the coil through a changing magnetic field, which is caused, for example, by a rotating ferromagnetic gear. The coil is wound on a magnetic core and led out via a cable or a plug. The sensors are manufactured with metric or inch threads or with a flange connection and deliver a sinusoidal output signal, the amplitude of which is proportional to the peripheral speed. They can be connected to Orbit Controls evaluation devices. An OC35-IMP transmitter is available for converting to square-wave signals.
-
Product
Differential Pressure Transmitter
616W
-
Positive, negative and differential pressures can be measured within a full span accuracy of ±0.25 with the Series 616W Differential Pressure Transmitter. Units are enclosed in a polycarbonate case, rated NEMA 4X (IP66) and operate by sensing the pressure of air and compatible gases then sending a standard 4-20 mA output signal.
-
Product
Suitable For RTD Sensors Approved To ATEX And IECEx Standards
TTR200X -
-
The TTR200X is our mid range transmitter for RTD or Slidewire sensors approved to ATEX and IECEx standards. It can accept many different types of RTD sensor such as Pt100, 500, 1000 etc and slidewire sensors up to 100K Ohm
-
Product
Fuse Circuit Breaker and Fault Finder
-
Shanghai Beha Electronics Co., Ltd.
*is a Fuse and Fault Finder which comprises of two parts: The Receiver and the Transmitter.*Locating and tracing of cables*Finding Circuit Breaker/RCD
-
Product
Standard Clamp-On Ultrasonic Transmitter
KATflow 100
-
The KATflow 100 is a compact clamp-on ultrasonic flow transmitter with a robust and practical design for permanent installation and flow measurement on single pipes.
-
Product
Mini Receiver
FB7-NX
-
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
