Filter Results By:
Products
Applications
Manufacturers
Backplanes
An interconnection structure allowing multiple printed circuit boards to coexist using a single bus.
-
product
Power Interface Board 6U, 2 PSU connectors
106PIBM602-0000R
The PIB 6U 2 slot has one power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
-
product
3U CompactPCI Enclosure with 6-Slot Backplane and Redundant Power Modules
cPCIS-3048
- 3U CompactPCI backplane with one system slot and five peripheral slots- Suitable for rackmount applications- 3U 48HP fanless enclosure- Optional redundant CompactPCI power modules
-
product
Electronical Load Board 6U VME64x (air cooled)
056-301
The 6U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
CompacFrame Type 39PS, Short VPX Payload Test And Development Platform
Type-39PS
Elma’s Short VPX CompacFrame platform is designed to accelerate development and test of boards designed to fit a smaller form factor of 3U boards (3U x 100mm deep). Accommodates up to 4-slot OpenVPX or 2 VPX power & ground only backplanes.
-
product
3U CompactPCI® Subsystem with 8-Slot Backplane and 400 W ATX Power Supply
cPCIS-2630 Series
- 400 W ATX Power supply- 3U CompactPCI® backplane with seven peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports rear I/O backplane with P2 connectors for cPCI 50mm/80mm depth RTMs- Temperature, voltage, and fan monitoring LEDs
-
product
3U VPX 1 Slot P&G backplane with aperture for VITA 66.4
101V301P06-9X13
Power for 3.3V, 5V and 12V per VITA 46, with all rear connectors fully loaded. Use with Elma’s slot-to-slot or slot-to-I/O bulkhead cable products for system development.
-
product
VXS 21 Slot
The Comtel VXS Backplane 21 slots match performance and cost-effectiveness by realising a fully optimised signal and power distribution environment. Design techniques ensure uniform impedance controlled signaling environment and ground guarding minimises line-to-line crosstalkThe VXS provides the high-speed switched serial performance of VITA 41, hybrid design includes VXS payload slots, VXS switch slots and conventional VME64x slots, The 21 slot VXS backplanes supports data rates well beyond 3.125Gb/s per link. As a dual-star design, it can be operated with two switch boards, allowing addressing of both link ports on payload cards.
-
product
VME64X 7U 4 slot no P0
101V64XM04-0620R
7U VME64x Backplane 4-slot w/o P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
product
Electronic Load Board 3U CPCI-S (air cooled)
056-377
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Gigabit Ethernet Switch
VPX6-688
Curtiss-Wright Defense Solutions
The Curtiss-Wright VPX6-688 Gigabit Ethernet switch was designed to provide a complete networking solution for VPX systems. Suitable for a wide range of embedded computing and vehicle network applications, the VPX6-688 provides 24 ports of IEEE 802.3 compliant 1000BASE-T Gigabit Ethernet to the backplane. Optional optical interfaces provide four 1000BASE-SX Gigabit links.
-
product
ATCA 7U 14 Slot dual star
109ATCA714-000XR
The Elma Electronic 5U ATCA Dual Star backplanes feature pluggability and redundancy "everywhere". There are pluggable connectors for fan trays, shelf managers, and power entry modules.
-
product
Rack Mount Osprey Chassis Q-Bus
0248-Q
4 Quad, 8 Dual height boards or a combination of quad and dual boards. AT style Motherboard, 3, 5-1/4" Bays, 2, 3-1/2" bays, 1 hidden, 1 exposed. this chassis is FCC/CE certifiable**. A quad-height Qbus backplane, cooling fans, and slides are provided plus space for a standard PC motherboard, diskette and hard drives (three visible and one hidden half-height bays), and up to four quad-height Qbus compatible cards.
-
product
3U 2-slot OpenVPX Backplane Aligned To SOSA™ - VITA 67.3c Aperture In Slot 2
1SVX302AMP-1X31
Designed in alignment with SOSA, this 3U backplane offers 2 Plug-in Card (PIC) slots to support the DoD’s MOSA and CMOSS initiatives. The backplane supports high-speed signals on all data paths and VITA 67.3c aperture in slot 2.
-
product
Benchtop Measurement Bundle With SMU
The Benchtop Measurement Bundle provides a PXI Express- and Thunderbolt™-based measurement system that features a chassis with a high-bandwidth, all-hybrid backplane. With the SMU, you can make use of precise voltage or current sourcing and measurement capabilities for PXI systems. Additionally, you can use analog-to-digital converters to help you perform high-precision measurements.Thunderbolt is a trademark of Intel Corporation or its subsidiaries in the US and/or other countries.
-
product
6U And 7U VPX 1 To 15 Slot Power & Ground Only Backplanes
101VPX6xxP-xxxx
Elma’s 6U / 7U VPX power and ground only backplanes provide a cost-effective way to design and test cards using the VPX architecture. The only assigned pins are for 3.3V, 5V and 12V power, and both ground and utility planes are defined.
-
product
14-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/14
*1 PICMG, 4 PCI and 9 ISA*Compatible with AX61400, AX6145, and AX6156LE*Supports both AT and ATX power supply
-
product
cPCI Serial Backplanes
CompactPCI Serial is an industrial standard for modular computer systems. It is based on the established PICMG 2.0 CompactPCI standard, which uses the parallel PCI bus for communication among a system's card components. In contrast to this, CompactPCI Serial uses only serial point-to-point connections.
-
product
VME J1J2 Monolithic 7 slot
101VMEM107-0500R
VME J1J2 Monolithic backplane 7 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
VME64X 7U 16 slot with P0
101V64XM16-0621R
7U VME64x Backplane 16-slot with P0, compliant with ANSI/VITA 1.1-1997, VME extension, and VITA 1.7 Increased Current. The extra 1U provides room for extra power bugs or busbars. Includes termination passive inboard and daisy chain automatic active.
-
product
3U – 6U SOSA™ Aligned VPX Backplanes
Using a modular concept based on open standards it is common practice in the civil sector to integrate subsystems components from different manufacturers into a single modular system. The SOSA™ Technical Standard aims at such an interoperability in embedded computing for military applications.
-
product
14-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB100
The FAB100 features one CPU card slot, four ISA slots, four PCI-E x1 slots, one PCI-E x16 slot, and four 32bit/33MHz PCI slots. This PICMG 1.3 backplane also supports a built-in 24-pin ATX power connector. Furthermore, the FAB100 delivers outstanding system performance through high-bandwidth interfaces such as Serial ATA and USB 2.0 high speed peripheral (optional function). It is designed for all of PICMG 1.3 single board computers, and is a perfect fit for AXIOMTEK's SHB100 & SHB110, which are built around the PICMG 1.3 form factor. We also have various 4U-high enclosures, AX6156E, AX6156LE, AX6156LLE, AX6156LLES, AX61400, AX61491 and AX6145, to house the FAB100 and any customer's industrial integrations flexibly.
-
product
VME J1 9 Slot with ADC Connectors
101VMEJ109-0590
VME J1 backplane 9 slot, compliant with ANSI/VITA 1-1994. 8-layer stripline design Includes passive termination inboard and automatic daisy chain connectors.
-
product
Digital Interconnect Test System, Reference Solution
When you need to measure advanced S-parameters with a fast, low-cost and easy-to-use test solution, the Digital Interconnect Test System gives you a significant edge. It provides a full 32-port vector network analyzer (VNA) configured within a single PXI chassis – ideal for high-speed cable testing. And lets you test any linear passive interconnect faster and easier, including backplanes, connectors and PCBs. Sharpen your edge with Keysight’s Digital Interconnect Test System that enables signal integrity characterization of multiport interconnect products.
-
product
6U VPX Power Interface Board VITA 62
106PIBC601-0000R
6U Convection Cooled VPX Power Interface Board, VITA62 compliant. Power Interface Boards (PIBs) facilitate the use of pluggable power supplies and headers with the power section of the backplane.
-
product
SpaceWire PXI Mk2
The SpaceWire PXI Mk2 card is a versatile SpaceWire Interface, Router or RMAP Target device. The card is designed to be an efficient host interface to a SpaceWire system or network, by utilising a cPCI or PXI backplane.
-
product
RF Coaxial Interconnect System VPX Compatible Rectangular Harness Solutions
VITA 67 Rectangular Harness
VITA 67 is a VPX standard for blindmate coax connectors that allows high density, high performance RF connections to be made between a backplane and plug-in modules.
-
product
sbRIO-9403, Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module
780539-01
Non-Enclosed, 5 V/TTL, 32 Bidirectional Channels, 7 µs C Series Digital Module - The sbRIO‑9403 is a configurable digital I/O interface for input or output with shift‑on‑the‑fly capabilities. Each channel features transient isolation between the I/O channels and the backplane. With reconfigurable I/O (RIO) technology (CompactRIO only), you can use the LabVIEW FPGA Module to program the sbRIO‑9403 for implementing custom, high-speed counter/timers; digital communication protocols; pulse generation; and other applications.
-
product
LXI High Voltage Matrix - 400V 50x4 Matrix Plugin Module
65-218-101
The 65-218-101 plug-in module is part of a scalable high voltage matrix platform designed to provide a large matrix solution with a switching capacity of 400V. This version of plug-in includes access to the chassis backplane.
-
product
3-slot ATX-supported 1U Butterfly PICMG 1.3 Bus Passive Backplane
FAB209
*Designed for PICMG 1.3 SBC*Compatible with AX61120TP chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot and one PCIe x16 slot
-
product
640 Gb/s Digital Signal Processor
M8132A
The M8132A is a powerful digital signal processing module featuring two customers accessible Xilinx Ultrascale+ FPGAs, four optical data interfaces (ODI) running at up to 160 Gb/s in+out each, and a PCIe Gen3 x8 link to the AXIe backplane. In addition, the module provides a trigger input and output, synchronization input and outputs for deterministic latency between compatible digitizers and AWG modules as well as a 10-general purpose I/O pins. The M8132A is part of Keysight’s Wideband Solution Platform that consists of a portfolio of compatible instruments, including digitizer, arbitrary waveform generator, digital signal processor and storage modules.
