Test Access Points
network jump enabling undetectable data monitoring. Also known as: TAP
See Also: Network Monitoring, Network Taps, Aggregator Taps
-
Product
Passive Tapping Solution
GPON Phantom™
-
GPON Phantom™ is a unique passive tapping device for Lawful Interception (LI) of optical fiber lines using GPON technology and deployed in a Fiber-to-the-x (FTTx) topology. The GPON Phantom records and stores broadband digital information, offering unique advantages for Law Enforcement Authorities (LEAs) looking to capture any data between the central office and the target, without being detected, while providing solid evidence with unique identification of the target.
-
Product
RF Taps
-
Praxsym’s RF Taps afford access to a cable system for monitoring function and performance without interrupting service. The taps also cause minimal insertion loss when the coupled port is open, as in normal system operation. Like all Praxsym products, these high-quality devices have honest specifications, and are well-documented over the bands they are designed for.
-
Product
Energy Probes
RjP-400 Series
-
The RkP-400 Series probes consist of a compact detector assembly, or head, and a preamplifier housed in a separate enclosure. The external dimensions of all the 400 Series Probes are the same, with identical detector planes, allowing for easy interchange of probes in an experiment. The heads have both ¼-20 and M6 tapped holes, a built-in 1" (25mm) filter holder, and a side-mounted BNC connector. Probe specific data, including spectral response curves and calibration dates, is stored in the preamplifier for access by the instruments.
-
Product
LAN Packet Tester
LE-590TX
-
The LE-590TX is a LAN analyzer that connects to a PC's USB2.0 port. In TAP mode, you can capture full duplex data on 10/ 100Base-TX and transmit to the PC at 480Mbps via the USB2.0 interface. In PG mode, you can generate test packets at up to 100Mbps line rate.
-
Product
USB Explorer (Two Port)
JT 3705
-
The JT 3705/USB Explorer is a low-cost two port USB powered boundary-scan controller interface specifically suited for low volume testing and in-system programming of (C)PLDs. Explorer supports two fully-compliant boundary-scan test access ports (TAPs) which can be synchronized for test purposes.
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TW Series
-
RMO-TW series is perfect for winding resistance measurements of inductive objects. It is ideal for testing transformer windings (power transformers, distribution, autotransformers) and for on-load tap changer verification. In addition, any RMO-TW transformer ohmmeter & tap changer analyzer can also perform transformer demagnetization.The series contains 4 models, with maximal test currents from 10 A (RMO10TW) to 50 A (RMO50TW). They are fitted in a portable and lightweight metal housing.All transformer ohmmeters from RMO-TW series generate a true DC ripple-free current with automatically regulated measurement and discharging circuit. The injection of current and discharge of energy from the test object are automatically regulated.Three independent channels enable testing of three windings in series. Consequently, this enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.DV-Win software enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test. Finally, a user can export all results in the form of a report.
-
Product
Distribution Amplifier
-
AVLINK TECHNIC TAIWAN CO., LTD.
Is a device that accepts a single input signal and provides this same signal to multiple isolated outputs.These devices are important because they allow a signal to be distributed to multiple destinations without ground loops or signal degradation. They are used for a number of common engineering tasks, including multiple amplification, cable television, splitting monitor and front of house mixes, and "tapping" a signal prior to sending it through effects units to preserve a "dry" signal for later experimentation.
-
Product
DXN Portable Hybrid Ultrasonic Flow Meters
-
The Dynasonics DXN meter is a powerful tool for troubleshooting flow issues, whether you want to quickly verify the flow reading of another meter or to data log flow system values over an extended time period. The DXN portable meter has transducers that clamp onto the outside of the pipeno tapping or cutting is required. The meter can be easily moved and installed in different locations. The large color display makes it easy to read and the setup wizard walks you through the meter configuration steps.
-
Product
High Side Current Sense Amp
QA150
-
The QA150 makes ultra-low current measurements of your toughest real-time projects a snap. The QA150 is a high side current to voltage converter. Simply tap into the supply for your various project rails (5V, 3.3V, etc) and the QA150 will convert the currents to voltages that you can then capture on your scope, along with whatever other signals you might need. If you are trying to squeeze every last bit of energy from your batteries, the QA150 is your answer.
-
Product
Transformer Winding Resistance Meters
TWA Standard Series
-
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
Product
Versatile Test Stand
VTS-2100
-
Applied Scientific Instrumentation
*Base is a Breadboard on 25 mm centers tapped for M6 screws with threaded holes for risers for TE/TI-2000, TE-300, IX-71/81, DMI, and MS-2000 stages.*Base feet provide vibration isolation.*Z riser is adjustable on pillar blocks.*Z motion from LS-50, LS-100, or LS-150 linear stage.*Z illumination can use LED, LED and a Condenser (from below), or fiber illumination (from above).*Observation is with a Modular Infinity Microscope.
-
Product
High Speed Device & Flash Programmer
JT 2147 QuadPOD
-
The JT 2147 QuadPOD high speed device programmer and flash programmer comprises JT 2148 transceiver and four independent, programmable JT 2149 TAP PODs and provides signal conditioning for the DataBlaster series of boundary-scan controllers. Used for gang, parallel, fast testing / Programming of devices.TAP pods can be housed integrally within the transceiver or they can be detached and reconnected via the (optional) one meter extension cable. The JT 2148 transceiver is available in standard (/10) or industrial (/13) variants. The /13 variant includes a SCSI cable splitter to allow system integrators to use flat ribbon cables into the transceiver itself which often simplifies fixture building.A fixture-embedded variant of the JT 2147 is available as part reference JT 2147/FXT. This unit integrates the function of the transceiver and four pod onto a single assembly. This variant can also support 64 DIOS channels and SCIL functions (see more images below for a picture of the JT 2147/FXT).
-
Product
USB 3.0 Cameras With CCD
xiD
-
*Quality components - Sony "EXview HAD CCD II" sensors delivering 2.8, 6.1, 9.1 and 12 Mpix*Fastest - Highest speed using full 4 TAP readout potential*Industry standard interface - Compliant with USB 3.0 SuperSpeed specification*Versatile mini camera - Subtle 60 x 60 x 39 mm, 320 grams (1)*Power - Lowest power consumption starting at 3 Watt, bus powered with USB3 cable*Cool - Minimal heat dissipation with passive COOLing*Compatibility - USB 3.0 support for Windows 7 and 10, macOS, Linux, ARM and 30 Libraries*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Bandwidth potential - 5Gb/s interface 400Mpix/s data throughput*Software interfaces - GenICam / GenTL and highly optimized xiAPI SDK for Image Processing*High grade - Quality class of sensors is combined with specially selected IR filters *Easy deployment - Range of accessories and widest hardware and software interoperability*Highly Customizable - Available in Board level and with Peltier TE Cooling
-
Product
Test Automation Platform (TAP)
-
The Keysight Test Automation Platform (TAP) provides powerful, flexible and extensible test sequence and test plan creation with additional capabilities that optimize your test software development and overall performance. TAP is a modern Microsoft .NET-based application that can be used stand-alone or in combination with higher level test executive software environments.
-
Product
PXIe-8523, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module
787311-01
Ethernet Interface
PXIe, 4-Port, 100/1000BASE-T1 PXI Automotive Ethernet Interface Module - The PXIe-8523 is a 100/1000BASE-T1 unshielded twisted pair (UTP) PXI Automotive Ethernet Interface Module for developing applications with the NI‑XNET driver. With this hardware, you can develop applications … that require Automotive Ethernet to test and validate automotive electronic control units (ECUs). The PXIe-8523 provides up to four independent endpoints or up to two network terminal access points (TAPs). It features onboard hardware timestamping and can act as up to four separate 802.1AS masters or slaves, so it can synchronize with an external network as well as the rest of a PXI system. The PXIe-8523 also provides LEDs on the front panel to help you monitor the network link and activity.
-
Product
Transformer Winding Resistance Meters
RMO TW Series
-
The RMO-TW instrument can perform a simple, fast and reliable verification of a transformer on-load tap changer. This instrument allows measurements of a winding resistance at each tapping position of an on-load tap changer without discharging between tests. Problems with OLTC switching, such as interruption, can be detected with these measurements. The results are displayed on a backlit LCD screen.
-
Product
Transformer Ratio Meters
-
The TRT is based on state-of-the-art technology and uses the most advanced technique available today. The test equipment can be used to test both single-phase and three-phase transformers, both with and without tap changer in accordance with the requirements of IEC 60076-1.
-
Product
TAP Detectors And Power Monitors
-
The “Premium” jumpers are VZ TPR Certified Cables that provide the highest level of reliability. We also offer the high performance “Standard” jumpers that are Telcordia GR 326 tested and certified. Both the Premium and Standard cables are made in our state of the art manufacturing facility recognized by leading global service providers as one of the best in the industry. We attribute our success to the highly dedicated and skilled production team which starts by selecting only the highest quality fiber and connector components.
-
Product
M-TAP Fiber Test Tap
-
The Maxcom Fiber Tap (M-TAP) is a portable optical test tool designed to minimize customer downtime. Two Splitters/Taps One Portable Device 80/20 split ratio 50/50 split ratio
-
Product
Temperature Sensors
TT420
-
Features • 2-wire, loop-powered 4-20mA analog output • Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner • Compatible with PLCs, meters, and data acquisition systems • No user calibration • TT420Z 1/4" stainless steel probe • TT420S 1/4-28 threaded stud – screws into any 1/4-28 tap • TT420F mounts onto any flat surface • UL listed, Intrinsically Safe (IS) • Class I, (C, D) and Class II, (E, F, G)
-
Product
RF Signal Detector
H-055DRV / 01019
-
The RF Signal Detector / 2G Cellular Phone Detector / Wireless Camera Detector / Bug Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices.
-
Product
PathWave Test Executive For Manufacturing Developer Version
KS8328A
-
PathWave Test Executive for Manufacturing (PTEM) is a plug-in that enhances the user experience in developing automated test programs using PathWave Test Automation Platform (TAP). With powerful PathWave Test Executive software, we eliminate the need to maintain or develop a test platform by users, especially in a manufacturing environment where a high mix of products exist, the maintenance, enhancement, and control of it could become challenging. Development of a test execution platform should not be a priority for valuable resources, instead optimizing and improving test coverage should be the key area of focus.
-
Product
BERTScope Digital Pre-emphasis
DPP Series
-
The Digital Pre-emphasis Processor DPP Series takes in single-ended inputs of data and clock and conditions the signal by adding precision amounts of pre-emphasis for use with Bit Error Rate Testers. Nine Tap Linear Equalization supporting speeds up to 32Gb/s is supported with the LE320 Series remote head, offering compact two channel precision equalization.
-
Product
Garland vTAP
-
With organizations becoming increasingly dependent on virtual computing, IT professionals need a solution to eliminate the blind spots inherent to virtual environments. Garland's vTAP is a software solution to address these challenges by providing complete visibility for east-west and inter-VM traffic. When used alongside Garland's physical TAPs, IT teams will have full confidence they are seeing every bit, byte, and packet® across their network.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
Phoenix 3U cPCI Camera Link Frame Grabber
AS-PHX-D48CL-3CPCI32-B-CR
-
Phoenix-D48CL is a 3U CompactPCI board for the acquisition of digital data from a variety of Camera Link sources, including digital frame capture and linescan cameras. It supports all the formats of the Base and Medium configurations, i.e. single 8- to 16-bit data, through 12-bit RGB, to four tap 12-bit sources, as well as dual Base configuration, i.e. acquisition from two asynchronous Base cameras.
-
Product
Handheld Broadband Noise Generator
NS-1
-
The Model NS-1 is a handheld broadband white Gaussian noise source. It generates a wide, even, RF noise-signal. The NS-1 is popular for testing network components and aligning a building's coaxial cable network. The NS-1's noise-signal is also used to provide the RF source for measuring insertion loss of cable, splitters, taps and more.
-
Product
On Load Tap Changer Analyzer
TAP4
-
The TAP-4 is the first instrument to use vibro-acoustic measurement to perform tests on On-Load Tap Changers (OLTC). The TAP-4 is a universal device, it adapts itself to any type of transformers: MR Reinhausen, ABB, Ferranti, Federal Pioneer and others.
-
Product
On Load Tap Changer Analyzer
TAP-4-PLUS
-
The Tap-4-PLUS is the newest instrument by Zensol for OLTC testing. It has 2 more analog inputs than the TAP-4. The TAP-4-PLUS with the TAP-DRM accessory can perform dynamic resistance, vibration, and motor current recordings at the same time. Doing so will allow you to easily understand the vibration impacts.
-
Product
Mini Back Probes/Wire Piercers
618
-
*Great for backprobing weather pack style connectors used with numerous automotive sensors *Also very handy for piercing and tapping readings on smaller gauge wires - using the included probe adapters *Works with most Test Lead Kits in the field - with standard 4mm banana plug test lead *Set includes four probes - red, black, green, yellow Test probes 21 mm length
