Unit Under Test
assures a constituent's interoperability in a system.
See Also: UUT, EUT, System Under Test, Device Under Test
-
product
ATE Self Test Fixtures
AL663
AL663 fixtures include all the electronic parts required to perform an effective test platform diagnostic. The AQ818 device allows to perform a series of tests, obtaining a report of the faulty instruments or switch modules and also a report about the relay contacts estimated life.
-
product
ARINC-708 Module
M4K708
The M4K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M4K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive.
-
product
SoC Test Systems
Specifically designed for high-throughput and high parallel test capabilities to provide the most cost-effective solution for fabless, IDM and testing houses. With the full functions of test capability, high accuracy, powerful software tools and excellent reliability, 3650-EX is ideal for testing consumer devices, high-performance microcontrollers, analog devices and SoC devices.
-
product
VXI Digital Multiplier
4152A
The 4152A’s advanced features like limit testing, averaging, speed/resolution trade-offs, and fast function changes provide the high “test system” throughput required in today’s production test environments.
-
product
PXI-2510, 68-Channel, 2 A PXI Signal Insertion Switch Module
778572-10
68-Channel, 2 A PXI Signal Insertion Switch Module—The PXI‑2510 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2510 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Battery Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
product
Functional Test
cUTS
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
product
NTS Platform
Manufacturers all over the world are leveraging our NTS platform for products with rotating or otherwise moving parts, or produce sounds. Typical applications include mass production of air conditioning units, pumps or small electric motors, where errors in assembly can cause malfunctions or significantly shorten service life. This test platform is customized to your specification and application. Feasibility studies are available to ensure your solution is exactly what you are looking for.
-
product
Wireless Device Test
New wireless standards, in addition to rising wireless usage, are increasing wireless device complexity while lowering price expectations. To counter rising costs, manufacturers require test systems optimized for efficiency.
-
product
3-Axis Non-Robotic Automated Testing System
AT3
The Instron AT3 is a space-efficient, highly adaptable 3-axis mechanical testing platform designed for automated execution of tensile, compression, flexural, and lap shear tests. Built to comply with a broad spectrum of ASTM and ISO standards, it’s well-suited for evaluating materials such as plastics, elastomers, thin films, foils, and metals. The system streamlines the entire testing workflow from specimen measurement and handling to strain measurement and specimen disposal—enabling users to load up to 160 samples and let the AT3 take care of the rest. Boost productivity, reduce manual intervention, and achieve consistent, dependable results with every test cycle.
-
product
6TL08 Benchtop Test Platform
H710008
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
product
PXIe-4139, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit
782856-02
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 20 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 20 W of DC power. This module features analog-to-digital … converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
PXI 10A Fault Insertion Switch 10-Chan 2-Bus
40-199-002
The 40-199 is a 10 Channel Fault Insertion switch designed for the simulation of fault conditions in automotive/avionics applications, involving the reliability testing of safety critical controllers.
-
product
3U OpenVPX Sensor Interface Unit
SIU32S
The SIU32S is a highly configurable Modular Open Systems Approach (MOSA) rugged system or subsystem ideally suited to support a multitude of Mil-Aero applications that require high-density I/O, processing, communications and Ethernet switching. The SIU32S leverages NAI’s Configurable Open Systems Architecture™ (COSA®) 3U boards and smart function modules to deliver off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
product
Battery Management (BMS) Environmental Test System
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
product
PXIe 5-channel Source/Measure Unit, 500 kSa/s, 100 pA, 30 V, 500 mA
M9614A
The Keysight M9614A is a PXIe five-channel source / measure unit (SMU). It supports accurate measurement up to 30 V / 500 mA with resolution down to 6 μV / 100 pA.
-
product
Automotive Ethernet Test Fixture
AE6941A
The AE6941A automotive Ethernet electrical test fixture provides easy access to automotive Ethernet electrical signals so you can perform conformance testing and device characterization quickly and easily.
-
product
Source Measurement Unit
SMU8
The SMU8 offers high voltage SMU in a compact, 3U PXI / USB form factor. The SMU8 supports 0V to +4V 0.5A or 0V to +12V 25.6mA with FVMI, FVMV, FIMV, FIMI modes. 8 channel can be ganged to support high current driving.
-
product
Source Measure Units
NGU
Thanks to their extremely high accuracy and fast load recovery time, the R&S®NGU source measure units (SMU) are perfect for challenging applications. A special ammeter design is used to precisely measure current drains from nA to A in one pass – no need to make multiple measurement sweeps. The instruments’ short recovery times enable them to handle fast load changes that occur, for example, when mobile communications devices switch from sleep mode to transmit mode. With high speed data acquisition, every detail is detected down to 2 μs resolution.
-
product
In-line High-Density ICT System Series 7i
E9988GL
The E9988GL Keysight i3070 Series 7i Inline High-Density In-Circuit Test (ICT) system brings industry-leading ICT technologies into your automated manufacturing line, saving resources and optimizing your automated test strategy.
-
product
Modular Functional Test Platform
LX-OTP2
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
product
Off-Line Seat Operation Base Test Platform
6TL23
The 6TL23 is a bare rack for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation since there’s space for the operator’s legs under the fixture receiver.
-
product
Eagle Test Systems
ETS-200T
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
product
PXI Integration Platform
ATS-3100
The new ATS-3100 enables you to rise above the module level and shift your focus to the sophisticated test solution you’re actually building. Simply add your instruments, software, and customization to create a complete solution. Or, if you're short on time or resources, ask Astronics Test Systems to do the finishing work for you.
-
product
High-Density Precision SMU (100 PA, 30 V)
PZ2130A
The Keysight PZ2130A is a high-channel density precision source / measure unit (SMU) with 5 channels per module that saves space at a low cost per channel for a wide range of applications requiring numerous precision power supplies. Its seamless current measurement ranging function eliminates the time it takes to change the range and expands the dynamic range to cover multiple measurement ranges, which reduces test duration. These capabilities make the PZ2130A suitable for applications that require numerous precision power supplies, such as semiconductor reliability tests and integrated circuit (IC) tests. The Keysight PX0107A low noise filter adapter lowers its voltage source noise level, which makes the PZ2130A suitable for noise sensitive applications such as quantum computing as well.
-
product
PXI/PXIe Fault Insertion Switch, 32-Chan 2A, N/C Through Relays, Fault Buses on M & U
40-190C-212
The 40-190C-212 (PXI) and 42-190C-212 (PXIe) are fault insertion switches with 32 channels. They are part of a range of modules available with 74, 64 or 32 channels and are primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers.
-
product
6TL24 Combinational Base Test Platform
H71002400
The 6TL24 is the Base platform ideal for Combinational test (ICT+FCT) in low to mid volume, high-mix electronics productions. A dual-stage pushing mechanism will allow performing both, the FCT and the ICT test, without the need of changing the test platform and with a low cost fixturing technology. To do so, the exchangeable cassette fixture must be designed with two-level probes. IN the 6TL24, the second level is reached thanks to a pneumatic actuator.
-
product
High Precision Source Measure Unit (SMU) - Hybrid Compatible PXI, 100ks/S Programming/Measurement Speed
52400 series
Hybrid Compatible PXIFour quadrant operationHigh source/measurement resolution (multiple ranges)Low output noiseHigh programming/measurement speed (100k s/S) & slew rateOptional measurement logDIO bitsOutput profiling by hardware sequencerProgrammable output resistanceFloating & Guarding output16 Control Bandwidth SelectionMaster / Slave operationDriver with LabView/LabWindows & C/C# APISoftpanel GUI
-
product
Scienlab Battery Test System – Pack Level, 110 KW Extendable Version
SL1720A
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development.
