Depot Level Test
faults diagnosis down to nth degree for repair analysis and recovery.
See Also: System Level Test, Level, SRU
-
Product
Dynamics Testing
-
Dynamics testing evaluates a product’s ability to withstand stresses occurring during normal and adverse operating conditions. These tests can also include conditions found during transport and product installation. Dynamics testing is common in commercial, industrial, aerospace and military applications.
-
Product
Total Tank Level System
-
The Total Tank Level System is an intrinsically safe and explosion proof level sensor with several communication options. Outputs include Modbus RTU digital, dual 4-20mA and HART. The Modbus version is offered in a single housing and the 4-20mA and HART output product features a dual compartment housing and display.
-
Product
Radar Level Transmitter
DR6400
-
The DR6400, FMCW 24-26 GHz open air radar is a market entry level transmitter for solids from granulates to rocks. This model has proven PP Drop antenna design which is insensitive to product build-up.
-
Product
Compliance Testing
-
American Environments Co., Inc.
The American Environments Company, Inc. (AECO) provides comprehensive compliance testing services. Our laboratory is fully equipped to provide Electromagnetic Testing, Environmental Simulation Testing and Dynamic Testing. Compliance requirements are related to the marketplace being serviced. AECO provides compliance services for: Products Exported to Europe, FCC, Telephone Network Equipment and Medical Devices.
-
Product
2.5mm Test Wire Test Probe Pin
CX-3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test wire test probe pin 1.Application: Used to verify the protection of persons against access to hazardous parts. Also used to verify the protection against access with a tool.
-
Product
Temperature Test
Series T
-
The temperature test are characterized by high rates of temperature change, ease of programmability through our color touch panel, as well as extremely low noise levels
-
Product
Class 2 Sound Level Meter
SP79
-
The SP79 is a Class 2 sound level meter for on-site measurements in accordance with Noise at Work legislation in industrial and office environments. Featuring A and C frequency weighting and fast and slow time weighting, the compact design can be handheld, or mounted on a tripod for longer term monitoring of Min / Max values. Detailed recording and analysis can be made using the AC and DC outputs. The SP79 complies with BS EN 61672-1:2003 and is supplied with a detachable windshield and hard carry case. The large high contrast display includes both digital reading and analogue bar graph. An optional Class 2 sound level calibrator is available to verify accuracy before and after readings in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB.
-
Product
Non-Destructive Testing
-
The essential feature of active thermography is the targeted supply of energy to the test object. A temporal and spatial characteristic heat flow results depending on the geometry and thermal properties of the test subjects. Its progression on the surface of the test object is captured by a thermographic camera.
-
Product
Compliance Test, Development and Test Service
DinoStor
-
With its focus on solving critical backup problems associated with Network-Attached Storage (NAS), DinoStor delivers a broad range of products and services to benefit users and vendors of NAS solutions.
-
Product
Signal Level Meters
-
PeakTech Prüf- und Messtechnik GmbH
In the field of Cable TV, Broadcast TV, Satellite TV and the distribution of these signals there are several different types of meters used to measure the signal strength and or quality.
-
Product
Test Probes
-
Test Probes provide the vital link to transfer measurement signals as true and as undistorted as possible. Therefore these elements can be regarded as the heart of Test Fixtures – and for this very reason it is important for Equip-Test to offer high performance Test Probes with best quality and value, and thus ensure maximized ROI (Return of Investment) for our customers. Test Probes supplied by Equip-Test always provide the best-possible available solution for your contacting demands.
-
Product
L40 Series Vertical Mount Brass Buna Liquid Level Switch
L40-06-C1-15-NO
-
The L40 / L45 Series Vertical Mount Brass / Buna Liquid Level Switches are most commonly seen in OEM applications and other industrial inputs. The brass stem and buna float makes the switch ideal for oil, gasoline, hydraulic oil, and jet fuel applications, and can survive to 230°F in oil.
-
Product
Femtocell and Application Testing
-
About the size of a home ADSL Router, a Femtocell (also known as an Access Point Base Station) is designed to allow 3G enabled devices (Phones, PDAs, Laptops) to connect to a carrier's core 3G network even where the carrier does not provide a signal themselves. It does this by bridging between the Wireless 3G devices and the carrier’s network using the Internet. Specifically, it will be connected to a Router (ADSL, Cable or other) already providing access to the Internet. Calls made and data services used on the 3G device are then sent to the carrier (and received from the carrier) over IP.
-
Product
Conformance Testing
Clarinet-TTCN ATM ETS
-
Protocol: UNI 3.1 ATM Layer Conformance Test Suite for End SystemsIUT: ATM Equipment UNI 3.0ATS: ATM-FORUM standards af-test-0060.000 covers the test of UNI 3.0 ATM Layer of End Systems
-
Product
Multifunctional Safety Tests
-
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
Product
Mechanical Testing Services
-
BMP Testing and Calibration Services Inc.
Mechanical testing, which involves determining the mechanical properties of a material, is a crucial component of materials engineering. Tensile strength also plays a crucial role and is the most important measured characteristic. The maximum stress a material can withstand when stretched or pulled before breaking is known as tensile strength. When creating and constructing materials for various uses, this feature is crucial. So where to get these services from?
-
Product
Climate Test Chambers
-
Infinity Machine International Inc.
Climate Test Chambers by Infinity Machine International Inc. - for applications such as dust proof climate test chamber for lighting, dust climate chamber for lab, and more.
-
Product
Mechanical Testing
-
Mechanical testing typically includes measurements of the physical properties of materials. These properties include strength, stress, stiffness, hardness, toughness, resilience, load-through-time or fatigue.
-
Product
Custom Test Fixtures
-
Intrinsic Quality is proud to offer a variety of Test Fixture Development Services that include fixture building, tester interface building, harness building, troubleshooting, maintenance, design, and engineering. IQ’s fixtures are built to exacting specifications and configured to deliver quality production testing. Our global customers have trusted us for over 35 years to provide custom solutions applying leading edge technology. IQ consistently delivers cost-effective solutions with our client’s recognition and gratitude.
-
Product
Automatic Test Software
EasyTest 2.0
-
EasyTest © 2.0 is a set of common test automation software platform, with the definition of test engineering, test process editor, test program generation, test execution process, test data on a network share as one of the functions. Using EasyTest © 2.0 can easily set up a large network systems and ground test integrated test system, you can build standalone automatic test system, or automatic control equipment R & D engineers, and other data stored for use in research and development.
-
Product
Distributed Test Manager
DTM
-
The Distributed Test Manager (DTM) is a Windows™ application which enables many different types of system level testing by simulating multiple devices in a system. DTM is a system level simulator that is unique compared to other Triangle MicroWorks tools which test the communications of a single device. DTM is a highly extensible tool with multiple options for configuring devices, creating test cases, and simulating data in the system.
-
Product
Protocol Test Solutions
-
Reducing engineering development time, issue resolution cycles, and overall costs; increasing product quality, system reliability, and customer satisfaction.
-
Product
Microwave Testing
220
-
The PICOPROBE® MODEL 220, a high performance microwave probe which incorporates a WR-5 waveguide with our patented coaxial design techniques, has inherent low loss and low dispersion characteristics.
-
-
Product
Test Programming LabVIEW
-
With LabVIEW, National Instruments provides an industry standard for developing a test environment.Our employees have many years of experience in many areas of this development environment.
-
-
Product
Sound Level Calibrator
511E
-
Accepted internationally 1 kHz represents the "0 dB" reference point of A, B, C Weighting and other filters utilized in acoustic measurement. The Pistonphone - a mechanical sound source - offers a slightly higher degree of accuracy at a substantial increase in cost. In addition, the 200 or 250 Hz operating frequency is mechanically limited and not suited for measurements of filtered inputs. The 0.2 dB accuracy is quickly lost in the 0.7 to 1.5 dB tolerances acceptable for weighting filters at frequencies around 250 Hz.
-
-
Product
Contact Level Transmitters
-
Measure level of liquids, pastes, granulates, powders, and liquid interface
-
Product
Material Testing Software
MS100
-
Sinowon Innovation Metrology Manufacture Ltd.
MS100 is professional software for material testing in windows system, it is able to conduct tensile, compression, bending, shearing, bonding strength, peeling, tearing and other tests for rubber, plastic, leather, metal, nylon line, fabric, paper, aviation, packaging, construction, petrifaction, electrician, vehicle and other materials.
