Filter Results By:
Products
Applications
Manufacturers
-
product
Indicators
Choose from a wide range of indicators designed for high accuracy and high speed applications for the processing industries. PENKO’s range includes sophisticated products that are suitable for general use in trade applications including automatic and non-automatic weighing applications. Our indicators are designed with easy and comfortable operation in mind. A screen with good visibility, an intuitive operating panel and a quickly obtained stable weighing signal are all part of our high-performance indicators. The precision weighing capability also ensures reliable and accurate measuring information.
-
-
-
-
product
Dial Indicators
1. Always select the dial test indicator that best fits the application.2. Care should be taken while using a dial test indicator, try not to jolt the indicator, should you be unfortunate and drop a dial test indicator, get it re-calibrated/repaired before reusing it.3. Replace worn contact points only with those of a similar length from the centre of the ball stylus to the abutment shoulder.4. Always clean dial test indicators after use with a lint free paper or cloth and store the indicator in its box or in a dust free area.5. When using a dial test indicator, always position the dial test indicator in a horizontal plane to the surface media.6. Always use a rigid stand for mounting the dial test indicator.7. When measuring a rotating object, either between centres or in a vee block, ensure that the object is rotating in the correct direction. Never rotate the workpiece towards the contact point.8. When measuring a sliding object, only take readings when the object is moving directly towards the contact point, never away from the contact point or in a sideways manner.9. Avoid parallax errors by reading the dial directly from the front and square on to the dial.10. Never oil a dial test indicator as this attracts contamination, should the movement become erratic then the dial test indicator should be submitted to a reputable repair agent.11. Try not to expose dial test indicators to direct sunlight or in a high humidity environment.12. Never use a dial test indicator that has not been calibrated, if in doubt consult an appropriate authority.
-
product
Weight Indicators
WIM-Systems offers the market an extensive and complete line of weight indicators, weight controllers and weight transmitters , all of them manufactured under the strictest quality standards, based on the technology and experience developed by WIM-Systems throughout the years. several years of successful activities.Our weight indicators, weight controllers and weight transmitters are electronic devices developed with the purpose of translating the information issued by a scale or balance, to data understandable by the operator and in some cases its function also includes the transmission of information from the electronic attachment to the scale.
-
product
PRESSURE INDICATORS
NOTE: We are not selling or carry VDO & HONEYWELL pressure senders, we just making the gauges for it!
-
product
Flow Indicators
Flow indicator with rotor features a self-cleaning mechanism to ensure full visibility of the rotor at all times. Typical sight flow indicators suffer from poor indicator visibility through normal use from build-up that impedes observation of the rotor through the viewing window. Typically, for a sight flow indicator to be cleaned, it must be removed from the pipeline, cleaned and then replaced at some specified time, such as during plant shutdown. Unfortunately, dirt build-up does not typically schedule itself to correspond with planned shutdowns. Enter the KOBOLD DAA Series flow indicator. Simply twist the sight glass and the integral wipers clean the flow indicator's viewing area to allow unobstructed observation of the rotor. The offending contaminants are then simply washed away by the media flow. This process may be repeated as often as desired with no fuss and no downtime. The DAA is available with brass or stainless steel fittings with " to 1" NPT female threads. The DAA is also available without a rotor for observation of fluid condition.
-
product
Indicators - Test
Measures the deflection of the arm, the probe does not retract but swings in an arc around its hinge point.
-
product
Bar Indicators
Orbit Controls bar displays are flush-mounted display devices with one or two three-color bars. They can also be ordered with a digital display. The devices are designed for connection to various process signals and can be equipped with control outputs.
-
product
Loop Antenna
ZHX7-0.009-200-1486
Loop Antenna, Frequency 0.009~200MHz, Linear Polarization, N-Female
-
product
Load Cell Indicators
Procter & Chester Measurements Ltd
The instrumentation will power the load cell. The mV/V signal coming back from the load cell is converted by the indicator and displays the force in a unit (e.g.: Kg, kN, lb – customers choice). The indicator will need to be mounted in to a case or control rack for safe use.
-
product
Panel Indicators
Nieaf-Smitt produces analogue indicators for maritime applications. Keyword for our production and R&D is flexibility. All instruments are produced on customer request and built on order. We primarily produce navigation instruments for bridge, bridge wing and control room installation. For example for speed, RPM, rate of turn, and pitch. Especially rudder indication is a very important application.
-
product
Current Loop Adapter
OP-1C
This adapter supports current loop communications.The kit incorporates a communications circuit with photo-coupler isolation and constant-current power supply of insulated type, thus realizing not only monitoring but also easy communications testing with passive or active current loop devices.
-
product
Single Loop Controller
1462
The N4400 is a sophisticated, single loop controller which provides extensive profiling programming options for complex processes. The controller can create a profile with up to 121 segments, store up to 8 programs and configure and store extra programs on a PC.
-
product
Antenna, Loop
EM-6879 | 10 KHz – 30 MHz
The EM-6879 Loop Antenna is used for magnetic field measurements over the frequency range of 10 kHz to 30 MHz. The EM-6879 is designed for use with any 50 ohm Receiver System. The antenna has a balanced Faraday shield that reduces its response to electric fields to a vanishingly small amount so that it can produce a practically pure magnetic field response.
-
product
Voltage Indicators & Detectors
Digital Voltage Detector is designed for easily indicating AC voltage on Underground primary, Over head primary and Transmission conductors up to 999 kV. The large digital display can be seen and read at distances up to 50'. Unit is perfect for large system voltages from 4kV to 765kV Phase to Phase.
-
product
Test Loop Translators
This high performance test loop translator is intended for use in professional applications in Ku band such as satellite earth stations.
-
-
product
Loop Calibrator
6500 LC
Standard Electric Works Co., Ltd
● 4-20mA (1kΩ load, 24V Loop Supply).● 0.025% Basic Accuracy.● Simple Operation Interface.● Auto Ramp and Step Functions.● 0-20mA, 0-24mA selectable.● Incremental percentage setting : 0-100%.● Warning beeper when output is open.● 0-24V output.● The minimum load of 20kΩ on voltage mode.
-
product
Remote Indicators
ABB field indicators provide a convenient way to access the field instruments data when they are located in remote or difficult to access areas. Powered directly from the 4-20 mA current loop, they require minimal effort to setup.
-
product
Process Indicators
A comprehensive range of field-mount, wall-mount and panel-mount digital indicators.
-
product
Single Loop Controller
1400+
The 1400+ controller is an evolved product from the West N4100. The product benefits from having more versatile features and user-friendly functionalities such as remote setpoint inputs, digital inputs, plug-in output modules, a customisable operator/HMI menu, jumperless and auto-hardware configuration, and 24VDC transmitter power supply.
-
product
mA Loop Calibrators
AMETEK Sensors, Test & Calibration
Our mA loop calibrator is an economical and easy-to-use calibration device for sourcing and measuring mA signals. Measure and source current to 24 mA and measure voltage to 45 VDC. Combine our 24VDCPS with one of our handheld pressure calibrators to calibrate transmitters in the field.
-
product
Single Loop Controller
1460
he 1460 has been designed to provide immediate visibility to the operator. At a glance, the programmable displays will show you the measured variable, the set point and the parameter being edited, the number of cycles or time remaining, the recipe name and number and also whether the cycle is in a ramp or soak mode
-
product
Test Voltage Indicators
PRV240FS
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
product
Indicators & Displays
30,000 displayed divisionsOIML R76 ApprovedStainless steel IP65 housingMains powered with 12V DC option25mm wide angle LCD display with back light2 programmable function keys and navigation keys provide easy operationLinearity correctionGravity AdjustmentLi-Ion long life rechargeable batteryAuto Power offPanel mount, desk stand, pole/wall bracket mounting includedRS-232C data port standard, 2nd RS-232C port optionTicket printing with Date, Time, Ticket no, Gross, Tare & Net Weight100 product memories for check weighing and countingSmart dynamic weighing algorithm for animal weighingCE approved
-
product
Friction Flow Loop System
Friction Flow Loop System is used for testing the effects of friction reducers by circulating at high rates through different pipe diameters. Friction Loop designs vary based on the application required.
-
product
Single Loop Controller
1800+
The 1800+ controller is an evolved product from the West N8100. The product benefits from having more versatile features and user-friendly functionalities such as remote setpoint inputs, digital inputs, plug-in output modules, a customisable operator/HMI menu, jumperless and auto-hardware configuration, and 24VDC transmitter power supply.
-
product
Antenna, Loop
EM-6874 | 20 Hz – 30 MHz
The EM-6874 Loop antenna is nominally used 20 Hz to 30 MHz and is designed for uncalibrated substitution measurements of shielding effectiveness as described by MILSTD-285, IEEE STD 299, and NSA-65-6.
