Battery Charge Discharge
-
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
Electric Vehicle Battery Tester
-
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
Product
Battery Electronics
-
CAES Battery Electronics provide autonomous, dissipative, and continuous cell balancing to maximize available battery capacity, and therefore battery cycle life, throughout a mission.
-
Product
Lithium-Ion Battery Pack, B2983 / B2987
N1418A
Power Supply
Use for the B2983A femto/picoammeter and the B2987A electrometer/high resistance meter.
-
Product
Battery Test Systems
-
The Intepro’s battery test systems are configurable systems designed to test the latest Lithium Ion batteries and other high power density batteries and chargers. Combining high resolution, high powered charge and discharge systems, Intepro IBT line of battery test systems link to the battery management through the bus communication and fail-safe external monitoring of key battery parameters.
-
Product
Parallel Differential Battery Tester With Integrated Chamber
-
Accelerate your battery parallel test using our PDBT. Featuring an integrated chamber, it precisely conducts battery comparison test and fast measures battery's self-discharge current. Its portable, powerful design is perfect for innovative research applications.
-
Product
Battery Fault Insertion Unit
Fault Insertion Unit
The Battery Fault Insertion Unit (FIU) provides intelligent switching of cell-simulation channels for the Battery Simulator 1200. The switching capability enables simulation of open-circuit and short-to-rail fault conditions on any cell channel for the purposes of battery management system (BMS) testing. Additionally, a four-wire auxiliary input allows you to connect an external digital multimeter (DMM) instrument to any cell channel for very high-accuracy bypass current and cell voltage measurements. Each FIU provides 24 independently-programmable cell-switching channels for one or two 12-cell Battery Simulator 1200 units. Additional Battery Simulator 1200 and FIU instruments can extend functionality up to 120 series-connected cell channels.
-
Product
Single Cell Battery Chargers
-
Renesas offers single-cell battery chargers that extend the life of lithium ion (Li-ion), lithium polymer (Li-polymer), and lithium iron phosphate (LiFePO4) batteries.
-
Product
Standby Battery Testers
-
Franklin Electric - Grid Solutions
A user-customizable, flexible, efficient and economical battery management tool for service providers, operations, and maintenance teams.
-
Product
Universal Battery Checker
T-333
-
Able to test 12 different sizes of rechargeable and non-rechargeable batteries.
-
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
PXI Battery Simulator Module
41-750-001
Simulator
The 41-750 is a battery simulator module that can be used to simulate the power supplies of cellular phones and other portable battery devices. It features fully floating output terminals than can deliver voltages up to 6 Volts. The fast responding remote sense connections allow the module to regulate the supply voltage at the device under test.
-
Product
Automatic Battery
BATLV480
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Partial Discharge and Tan Delta
PDIX Series
-
PDIX is a combined partial discharge and tan delta cable diagnostic testing system. By combining HVI’s VLF products with PDIX products, users can perform VLF AC withstand, partial discharge detection, and tan delta measurement on medium and high voltage cables, rotating machinery, and other apparatus with one integrated package fully supported by HVI & PDIX.
-
Product
Corona Discharge Checker
MK-720
-
MK-720 enables finding of insulation deterioration on insulators, disconnectors, and circuit breakers, at hot-line condition!
-
Product
Large Current Battery Short Circuit Test Device
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL Large Current Battery Short Circuit Test DeviceApplication: Battery Module, Battery Pack, Battery System short circuit.Short Circuit Mode: Pneumatic drive contact + Vacuum Interrupter
-
Product
Battery Module
-
Each Gavia Battery Module contains several independent "smart" Li-Ion battery packs and battery chargers. Each battery pack is monitored for health and operational information, and the battery packs are protected against short-circuit and overcharge. The Battery Module also contains an intelligent power management processor.
-
Product
Low Voltage DC / Battery Powered HV Amplifiers
WMA-01 And WMA-01LF
-
The Falco Systems WMA-01 is a high voltage amplifier that runs from an 24 - 30V DC power supply and can be battery powered if required, e.g. for use in a Faraday cage. Its internal high voltage generator is inductor-free and hence does not spread magnetic interference in sensitive experimental setups. The output noise is impressively low at 3mVrms. For extremely low noise applications where bandwidth is not an issue, a dedicated WMA-01LF version is available that contains an output low pass filter capacitor which reduces the bandwidth to 50Hz, but makes the noise drop to below 0.1mVrms. This bandwidth-limited amplifier is ideal for MEMS or piezo positioning with manual voltage adjustment.
-
Product
Battery Charger / Analyzer
IC48V
-
The newest and most powerful battery charger / analyzer from Intelligent Charging, the IC48V has been designed for highest performance at the lowest possible weight.
-
Product
In-Line Charge Amplifiers
-
The in-line charge amplifier is used to excite structures or machinery with a definable impulse force. Resonances are identified by impulse, an important measurement parameter for the study of dynamic behavior. The 4705A1 is a fast turn on time, 50 mV/pc, in line charge amplifier with BNC jack connectors on each side.
-
Product
Cell, Battery, And Module Test Systems
-
Maximize your testing capabilities with Maccor's hardware and software. Our comprehensive turn-key systems come bundled with all the essentials to jumpstart your testing process. Select from multiple options and configurations to match your requirements.
-
Product
Battery Analyser 12V Language
BA12L
-
The Battery Analyzer 12V Language (BA12L) is a 12V battery analyzer with English language text display easy and convenient to use by technicians and users. Has 4 main function tests: Battery, Starter, Alternator & Grounding
-
Product
Partial Discharge Test
INDIPORT
-
For medium voltage switchgear - partial discharge test in a few minutes - without shutdown.
-
Product
Automatic Battery
BATLV360
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of power factor in low voltage instalations.
-
Product
Electrostatic Discharge Simulators
ESS Series
-
EMC test equipment to evaluate the resistibility of electronic equipment when electrostatic charges on a human body or object has been discharged to the electronic equipment.This product can be used for evaluating performance degradation of any types of electronic products.
-
Product
EV/HEV Battery Pack Environmental Exerciser/Monitor System
-
DMC designed, built, and programmed a set of automated test stands for charging and discharging electric vehicle battery packs. The test stands also monitor the performance of these battery packs while exposed to harsh environmental...
-
Product
CTEK PRO Battery Tester
40-209)
-
Complete with an integrated printer, it’s now easier than ever to determine and present the current state of a battery and electrical system with the CTEK PRO Battery Tester. The PRO Battery Tester performs quick, simple, and accurate battery or system testsin seconds without heat, sparks, or user interpretation. The results can then be printed and reviewed immediately with customers for added impact to preventative maintenance routines and customer service. The CTEK PRO Battery Tester is patented and features a 2-year warranty.
-
Product
Automatic Battery with Filters with Standard Contactors
BATLVF400
-
Lifasa - International Capacitors, SA
LIFASA automatic capacitor banks are used for centralized compensation of powerfactor in low voltage instalations
