Gel Cell Battery
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, 1 kV Isolation
43-752A-103
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Semi-auto 4 Point Probe System for Solar Cell Substrate
RG-100PV
-
*Measurement system for thin film on substrate samples for multi-points measurement*Even pitch and random pitch for Max.1,000 points*2-D/3-D square mapping software for even pitch
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
Battery Tester
G6606
-
Peaceful Thriving Enterprise Co Ltd
It can quickly test the capacity of your battery.
-
Product
Digital 125 Amp Battery Load Tester
6033
-
• Heavy load enables the 6033 to detect bad batteries missed by other electronic testers• Automatically computes the CCA of the battery under load• Kelvin connected digital meter displays the following values:• Current Battery Voltage• Maximum Voltage reading• Minimum Voltage reading• Automatic load cycle• PATENTED• Made in USA of US and Global Components
-
Product
Battery Simulator
G5.BAS
-
The G5.BAS series is bidirectional regenerative. It was developed specifically for the simulation of energy storage devices and batteries and is suitable for use in laboratories and on test benches. The modular and finely graded G5.BAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3.
-
Product
Power Cell Power Transducers for Wide Ranging AC/DC Loads
PH-3A and PH-1000
-
You can know the load on an electric motor by measuring the electric current going to the motor (Amps). But, this is not the best way to do it since a lightly-loaded motor doesn't use the electricity very efficiently. (In technical terms, the power factor is low.)A better way to know the load is to measure the motor power. (Power is measured in Horsepower or Watts.) Motor power gives you a straight line so it works well even when the motor is lightly loaded.The Power Sensors that we make measure the motor load (Horsepower or Watts) and send a signal to meters or computers. The operator can see what the status is on the meter or, the computer can make decisions.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, 1 kV Isolation
43-752A-102
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
Solar Cells
-
Using high-efficiency solar panels made of silicon solar cells, the conversion rate as high as 16%, and attenuation, good reliability, long life. Frame using a high-quality anodized aluminum edge, high mechanical strength, ensuring a high level of wind resistance and anti-riot performance, can be adapted to a variety of complex and harsh climatic conditions used.
-
Product
Lithium Battery Equalization Tester
LIFG-CT
-
Fuzhou Fuguang Electronics Co., Ltd.
LIFG-CT series tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem of inconsistent voltage of lithium battery pack.
-
Product
High Speed Load Cell Test Interface
LCIC-4CH
-
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Battery Discharge Test Unit
125V DC 100A
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Discharge Capacity Tester is used to perform discharge testing which is the verifiable method to determine actual capacity of battery systems.
-
Product
Battery Charge Discharge Tester
-
KV Hipot Power Test Equipment Co.,Ltd
Battery Charge Discharge Tester is a multi-function comprehensive tester which is not only a battery charger and Battery discharger, but a battery activator.
-
Product
Precision Integrated Analog Front End, Controller, & PWM for Battery Test & Formation Systems
-
The AD8452 combines a precision analog front-end controller and switch mode power supply (SMPS), pulse-width modulator (PWM) driver into a single silicon platform for high volume battery testing and formation manufacturing. A precision instrumentation amplifier (in-amp) measures the battery charge/discharge current to better than ±0.1% accuracy, while an equally accurate difference amplifier measures the battery voltage. Internal laser trimmed resistor networks establish the in-amp and difference amplifier gains (66 V/V and 0.4 V/V, respectively), and stabilize the AD8452 performance across the rated operating temperature range.
-
Product
Battery Powered, Multi-Range, Analogue Portable Instrument
Tester SA9083
-
The Tester SA9083 is a battery powered, multi-range, analogue portable instrument. It is primarily intended for use by faultsmen for maintenance testing of telecommunication lines and equipment, subscriber installations connected to exchanges where faultsmen do not have access to a test desk, or where the testing equipment at the local exchange is not staffed during normal working hours. It has three input terminals, a range selector switch and a dual purpose push-button reversing switch (B-A changeover/test cell).
-
Product
CTEK US 0.8 Battery Charger
56-865
-
US 0.8 is CTEK’s smallest 12 V charger. It offers state of the art technology and is perfect for charging smaller 12 V batteries that can be found in motorcycles, jet skis, ATVs and lawnmowers. It is also suitable for maintenance charging “normal- sized” batteries such as car batteries.The unique display allows the user to follow the entire charging process. The US 0.8 is a compact and fully automatic 6-step charger for 12 V batteries from 1.2–32 Ah and is suitable for maintenance charging up to 100 Ah. The US 0.8 is splash and dust proof, delivers 0.8 A and is designed to protect vehicle electronics. It is non-sparking, reverse polarity protected and shortcircuit proof. The US 0.8 is delivered with 5-year warranty.
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
PXI Mixed Configuration Relay Module - 7 Cells Populated
40-138-AA-BB-CC-DD (7 CELL)
Relay
The 40-138 2A Relay Module with 7 cells populated is a cell-based mixed configuration switching module suitable for applications requiring medium power switching with high density. It provides a broad selection of mixed relay types for greater flexibility and features 2A current capacity and voltages to 300VDC/250VAC.
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
-
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
Lithium Battery Equalization Tester
LIFG
-
Fuzhou Fuguang Electronics Co., Ltd.
The LIFG series Tester is an intelligent and efficient lithium battery equalization maintenance instrument, which is used to quickly solve the problem that inconsistent voltage of lithium battery pack. Meanwhile it supports to make the voltage difference of any battery, which can be used for research and development experiments to stimulate what problems will occur when the battery reaches the maximum voltage difference under harsh work working conditions.
-
Product
Handheld Digital Multimeter, 4.5 digit, up to 800 hours battery life
U1281A
Digital Multimeter
60,000 counts resolution on dual display0.025% basic DC voltage accuracy Longer battery life up to 800 hours Certified to IP 67 for dust and water protection Tested to withstand a 3-meter (10-ft) drop Programmable via USB (Download Programming Guide here)CAT III 1000 V/ CAT IV 600 V overvoltage protection
-
Product
Ancillary Test Cell Products
-
In addition to our innovative and industry leading AccuDyne AC Dynamometers and DynoLAB Test Automation Systems, SAKOR fully integrates a complete range of ancillary products and subsystems necessary for an advanced test cell. Examples include:*Combustion air consumption measurement and conditioning subsystems*Exhaust handling systems*Fuel consumption measurement and conditioning subsystems*Coolant and oil conditioning systems*Throttle actuators*Spark/Fuel controls*Combustion analysis systems*Complete exhaust emissions analysis systems (per 40 CFR 1065 regulations)*Sound attenuating (up to STC 52) test cell enclosures with several fire suppression options*Process water evaporative cooling tower
-
Product
Laptop Battery Pack Tester 20V10A
TOB-BTS-20V10A
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Battery Analyzer (10A 20V per Channel) with Laptop & Software for All Types of Batteries &Laptop battery Packs. TOB-BTS-20V10A Laptop Battery Pack Tester 20V10A is a 8 channel battery analyzing system for Li-ion, LiFePO3, Ni-MH, Ni-Cd, and Lead acid battery packs with voltage up to 20V and current up to 10A per channel.
-
Product
Robotic Cell for Testing Car Multimedia System
-
It is necessary to develop an automated system for testing a multimedia device. The system should perform functional testing: testing of physical buttons, touch screen and logic of operation.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 1 kV Isolation
41-752A-112
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
High-accuracy Dual-channel Programmable Battery Simulator
N8352 Series
-
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
N8352 series is specially designed for the R&D and testing of portable, battery-operated products , such as Bluetooth headsets, mobile, AR/VR smart terminals, electrical tools, etc. The current flows in both directions and can be used as either a power supply or a load. N8352 is easy for operation with touch screen and UI design. The output features are comparable to actual batteries, with fast dynamic response, no overshoot in voltage rise and fall, and stable waveform. The resolution is up to nA level, which can test the loop static power consumption, etc. N8352 can be widely used in the area of consumer electronics testing.
-
Product
Battery Simulator
-
The purpose of this battery impedance network (BNB) is to provide electric power to the device under test, providing a standard impedance. It has been developed for automotive tests. A resistor that emulates the internal battery resistance is implemented in the BNB.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
