Test Switches
-
product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196C
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
product
Laser Diode Burn-in Reliability Test System
58604
The Chroma 58604 is a high density, multi-function, and temperature controlled module for laser diode burn-in and lifetime tests. Each module has up to 256 SMU channels which can source current and measure voltage in various control modes as described below.
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
Environmental Control System Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
product
Electrification Testing Solutions
When looking for a partner to assist with your electrification testing or power electronics testing challenge, Ball Systems has the expertise and experience to ensure your energy storage or power conversion project moves forward efficiently.
-
product
Test System
BMS HIL
The BMS Hardware-in-the-Loop (HIL) Test System is a high performance platform providing all necessary input signals used for battery pack simulation. A real-time operating system executes complex cell and pack models commonly used for BMS algorithm development and firmware regression testing.
-
product
PXI/PXIe MEMS Optical Switch, Triple Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-332
The 40/42-860A-332 is a PXI/PXIe triple insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
Semiconductor Test Software
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
-
product
High Performance PXI Functional Test System with Mac Panel Interface
TS-5400
The Keysight TS-5400 PXI Series Functional Test System provides automotive, aerospace and defense and industrial control manufacturers with an off-the-shelf PXI hardware and software platform with support for single or multiple DUT test. Designed for testing electronics control modules such as, power train control, complex body electronics and industrial controllers, the TS-5400 PXI Series helps manufacturers achieve higher throughput for their design validation and manufacturing functional test needs with the capacity to empower them to anticipate future functional test needs.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and voltage ranges cover the test of frequent DUT operating parameters. Time-dependent voltage or current signals can be stimulated by an arbitrary generator with power amplifier. General measurements such as current, voltage, frequency, resistance can be carried out flexibly at various test points using the matrix concept. An oscilloscope with RF multiplexer is available for high-frequency measurements such as residual ripple, switching processes, etc.
-
product
PXI Hex SPDT RF Switch 3GHz 50 SMB
40-870-006
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
Flying Prober Test System
QTOUCH1404C
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
product
General Purpose Switching PXI Card
GX6125
The GX6125 is 3U high density switching card with 25 SPDT Form C relays with a switching power rating of 60 W. The GX6125 is suitable for all test applications requiring general purpose, low level switching.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
42-870A-106
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz.
-
product
6TL10 Table Top Test Base
H71001000
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettes.The platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
product
Test Workflow Pro
Test Workflow equips engineers with application-specific tools so that they can choose the right one for the job—from graphical programing environments to no-code and interactive software applications. Engineers can use Test Workflow software to perform quick ad-hoc tests, build an automated test system, automate data analysis and reporting, develop test sequences, and more.
-
product
HV Test System up to 20000 Volt
Insulated test booth with large space for test items. 2 banana sockets for AC connection and 4 banana sockets for the DC connection of the DUTs. IC’s are tested in a long-term test. These are checked in an oil bath so that there are no air gaps to reduce the insulation. Maximum voltage 20 kV. Therefore, insulation tests must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
product
Test Fixture (SMD Components)
16034E
Perform impedance evaluation on a minimum SMD size of 1.6(L) x 0.8(W) [mm]
-
product
Scienlab Battery Test System – Pack Level, 330 KW
SL1740A
Keysight’s SL1700A Scienlab Battery Test System – Pack Level Series allows to realistically emulate the environment of the future battery pack application in order to test the high-power battery pack comprehensively and improve its functions and safety. The growing demand of e-mobility increases the need of vast battery test labs for EV battery development. Keysight developed the SL1700A Series to accelerate the development and validation of batteries. It offers a voltage range of up to 1500 V and power options between 100 and 300 kW including a Performance Bundle to increase the power up to 330 kW. The new high-voltage SiC (silicon carbide) technology provides a high energy efficiency on a small footprint and helps to minimize your operating costs.
-
product
Photonics Wafer Probing Test System
58635
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 50 GHz, 50 Ω, SMA-2.4, Failsafe
42-782B-551
The 40-782B-551 (PXI) and 42-782B-551 (PXIe) single failsafe transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
-
-
product
Off-Line Testing Platform
6TL29
6TL29 Testing platforms are based on the modularity concept; its construction is completely modular and scalable, allowing the user to take advantage of a powerful and reliable platform with a minimum investment.The platform is compact and due to its reduced footprint can be integrated easily into any production line. It’s ideal for High-Mix Low-Mid Volume production environments.
-
product
12-Ch SPST 5A-250VAC High Current Power Switching
YAV90CIN
12 Independent SPST relaysSwitching up to 5A 250Vac12 current measurement channelsGeneral inhibit inputCAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
product
IOL & Power Cycling Test Systems
Our IOL & power cycling systems increase measurement quality and throughput and reduce testing costs on an open platform. The focus is on seamless monitoring and precise determination of all parameters of each DUT. In addition, the systems are equipped for the special requirements of wide-bandgap technology.
-
product
Scienlab Combined Battery Test Solution
SL1133A
Solution for testing battery cells with an output power up to ±3 kW and a voltage range up to 6 V.
-
product
Cable Free ATE
CABLEFREEATE
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
