Voltage Converters
Changes the voltage of a source.
-
Product
Dual-Range High Voltage Non-Contact Tester
HVNCVT-1
-
Use to check for the presence of voltage in overhead conductors or find faults in cables.LOW range for 50V AC to 1.5kV AC.HIGH range for 1.5kV AC to 132kV AC.Audible and visual signals indicate the presence of voltage.Water resistant.Includes durable carrying case.
-
Product
High Voltage Clip for Test Leads
-
- The new Parrot clips are high voltage gripping clips for test leads and probes. High Voltage Parrot clips replace insulated alligator clips, plastic coated miniature alligator clips, small crocodile clips or large alligator clips.- Parrot Clips have a design with a new metal tube tip which is connected directly to the lead.- The tip, the hooked rod and the spring are housed in a plastic support.
-
Product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 2-Pole
40-321-123-HI
Multiplexer Module
The 40-321-123-HI (PXI) and 42-321-123-HI (PXIe) are hex 7-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
High Voltage Isolator for Logic Analyzers
LX-08
-
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
Product
Voltage Amplifiers
-
Switchable gain up to 100 dB (x 100,000)Bandwidth DC to 100 kHzDC-drift 0.6 µV/°CInput noise down to 0.4 nV/√HzSwitchable AC/DC-couplingLocal and remote controlInput impedance up to 1 TΩ
-
Product
Plane Mirror Converter
10722A
-
The Keysight 10722A plane mirror converter modifies the use of the 10702A linear interferometer. With an additional 10703A reflector, the 10722A converts the 10702A into a 10706A plane mirror interferometer. With an additional 10723A high-stability adapter, the 10722A converts the 10702A into an 10706B high-stability plane mirror interferometer.
-
Product
DC/DC Converter 50 W
CTS-60-6843
-
DC/DC converter with 50 W from Premium | input ranges 43.2 - 90 VDC | output 5 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
Voltage Probes
-
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.
-
Product
LXI High Voltage Switching - 50xSPST Plugin Module
65-233-700-HI
General Purpose Relay Module
The 65-233-700-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 7 kV. Switch arrays are created by populating the 65-200-002 scalable chassis with plug-in modules that provide access to the switches on 51-pin front panel connectors. Users can specify as many or as few plug-in modules as they require and can field upgrade the chassis to extend the number of switches.
-
Product
LXI High Voltage Switching - 10xSPST Plugin Module
65-233-704-HI
General Purpose Relay Module
High voltage switch plugin module capable of cold switching up to 7 kV and hot switching up to 5 kV.
-
Product
AC Power Supply and Frequency Converter
P Series
-
The P Series AC Power Supply and Frequency Converter for your test bench or test rack delivers clean regulated AC power in a (2U) 3.5" high and (3U) 5.25” high bench top unit that easily converts to rack mount, for far less cost than competitive models.
-
Product
High Voltage Test & Measurement System
-
Hard-wearing and technically-sound High Voltage Test & Measurement System is developed to provide accurate results. These systems are widely used in power, electrical, engineering and other industries. They are designed using heavy-duty spare-parts to add strength with life to the systems. They are ideal to provide accurate results without any flaw to ensure to provide the best performance. These systems are perfect combination of easy usage, durability and high accuracy in results.
-
Product
Non-Contact Voltage Testers
-
PeakTech Prüf- und Messtechnik GmbH
User-friendly tester for non-contact voltage testing from 50 V to 1000 V AC. Suitable for outlets, lamp sockets or against wire insulation testing. If AC voltage is present at the relevant measuring point, this is indicated visually by a flashing red LED and the integrated buzzer sounds. If the measuring point is voltage-free, the test probe lights up permanently green.
-
Product
50 Ω High Voltage Pulse Generators
-
High Power Pulse Instruments GmbH
50 Ω High Voltage Pulse Generators by HPPI GmbH
-
Product
Low Operate Voltage Relays
DGG Series
-
Heavy duty relays wth extremely sensitive coil (pull-in 0,4 x Unom) for demanding applications.
-
Product
Converter Signal Amplifier – 4…20 mA – Wall Mounting
HD978TR5
-
Configurable converter signal amplifier with 4…20 mA (20…4mA).
-
Product
2kV, 80 MHz High Voltage Differential Probe
HVD3206A-6M
-
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
Product
High Voltage Ammeter
Ampstik®+
-
Use the Ampstik+ to safely take accurate current measurements when performing high voltage live-line load checks for balancing, switching, or breaking load. This high voltage ammeter measures in every electric utility setting with a linear current sensor to accurately measure .5A to 5000A, while in voltage environments up to 500kV. The opening of the amp sensor is electronically closed, while external currents are electronically rejected. This design enables the user to measure an individual conductor within close proximity to adjacent conductors without interference errors.
-
Product
Transition Time Converter, 150ps
15435A
-
The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters.Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications.The converters are fitted with SMA connectors, one male, one female.
-
Product
High Voltage Probe
HVP-39pro
-
* 39KVDC+ACpeak* 900MΩ Impedance* DC~50MHz(-3dB)* 1000:1 for Oscilloscope* Very Low Nosie
-
Product
Voltage Tester, LED
72-9395
-
*Easy to use voltage tester designed for the professional user*Waterproof and rugged making it ideal for nearly all situations*Continuity test*690V max*Short circuit detection*Automatic range selection*Single lead voltage detection*Phase rotation test (50-60Hz)*Polarity detection*Built-in LED light*Rubberised grip*12 month limited warranty *view Terms & Conditions for details
-
Product
AC Voltage Proving Units
HLV-2
-
Standard Electric Works Co., Ltd
The AC Voltage Detectors and AC Voltage Testers utilized to determine if the devices under test are functionally working. They are not a calibrator and cannot be utilized for calibration.
-
Product
D/A Converter
DA-4130
-
The DA-4130 D/A converter converts BCD output signal from Ono Sokki's digital gauge DG-4000 series, RV series reversible counter or other devices into analog signal to be recorded with pen recorder, etc.
-
Product
Solid State Voltage Injector
J2110A
-
While it is possible to obtain high quality injection transformers with bandwidths as wide as 1Hz to 5MHz or more, in some cases this is still insufficient for some tests. For example a typical heater control loop might have a bandwidth of less than 1Hz while some linear regulators and opamp circuits can have bandwidths of up to 100MHz or in some cases even higher. For these applications, a solid state injector can provide the necessary bandwidth. A solid state injector can perform at DC, while the upper frequency limit is dictated by the components selected and the printed circuit board material and layout. It is possible to obtain a solid state injector with a working range of DC – 200MHz, though above 50MHz the interconnection between the injector and the circuit being tested can become quite critical. It is essential that ripple from the injector power supply does not dramatically degrade the dynamic range or the signal to noise ratio of the measurement. The resulting plots are often much cleaner when using a solid state injector than with a transformer injector.
-
Product
Auxiliary Voltage Relays
AVR
-
Type AVR volta acquisition systemscontrol/datage acuated relays are designed for indication alarm of annunciation in elextric utility application. the relays are used for data inputs to supervisory and sequential event recorders
-
Product
PXI Voltage Amplifier SMB Type Connector
41-650-002
Amplifier
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.
-
Product
4 or 8 Channels In-Line Real-Time ARINC-Ethernet Converter
NLINE-EA429
Ethernet Interface
NLINE-EA429™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). NLINE-EA429 is a small, low-power, rugged device that provides connectivity for 1-8 ARINC 429/575/573/717 Channels – Ideal for remoting ARINC connections for in-field applications or point-point lab usage.
-
Product
HV High Voltage Detector
-
The Motwane Manufacturing Company
For decades, Motwane Voltage Detector has been a standard for international quality and safety ratings. Voltage detectors are used to signal the presence of voltage in a conductor since they make visible what we normally can’t see. Its application lies mainly in safety reasons during research, or when a service operation is under way. Most of the time, the monitored conductors come from low impedance sources whose voltage and energies are considered life-threatening.
-
Product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 2-Pole
40-321-121-HI
Multiplexer Module
The 40-321-121-HI (PXI) and 42-321-121-HI (PXIe) are quad 5-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
Product
Voltage Controlled Oscillator Assembly With Heater
-
Teledyne RF & Microwave has designed a Voltage Controlled Oscillator to replace an existing application. The oscillator covers the 520 to 560 MHz frequency range. The oscillator provides +10 to +13 dBm output power. The oscillator has internal heaters designed to maintain the oscillator assembly at constant temperature. The unit operates over the 0° to 60° C temperature range with ~200 KHz frequency variation due to temperature variation.
