Filter Results By:
Products
Applications
Manufacturers
-
product
Fuel Injection Pressure Tester with 2 Gages
33950
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Test all Ford vehicles with multi-port fuel injection systems.Includes two gages: Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR).
-
product
Pump Testing in Repair and Maintenance
Test field for dry installed and submerged centrifugal pumps as acceptance test field in maintenance
-
product
Automotive Engine Tester
QCM-2A
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to integrated test varieties of automobile motor, wiper motor, window lifting motor, oil pump motor etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stators.
-
product
Pump Testing Panels
Aarohi Embedded Systems Pvt. Ltd
AAROHI Pump Testing Panels - full load, semi/fully-automatic pump test systems
-
product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
30 AMP Fuse Buddy Testers
FB305M
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
product
EDFA
SPA-10G-32
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by thebutton in the front panel or by web snmp. *Output adjustable by buttons in the front panel or web snmp, the range is down 4dBm *Max multi 32 port, with built in1310/1490/1550/1270/1577/WDM,max total output 38 dBm *Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in snmp hardware can be reserved for update. *With laser key to turn on/off the laser.*With RF test function. *Adopts JDSU Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
product
Hydraulic Test Systems
Genuen specializes in hydraulic test stands, including component tests, pumps, motors, valves, actuators, fatigue, load frames, and burst testers. As an industry leader in custom test systems, we focus on hydraulic solutions that leverage off-the-shelf technologies for mechanical subsystems and components. Our hydraulic test equipment has been deployed in aerospace and defense, automotive, industrial, commercial, and many other industries.
-
product
Pneumatic Test Pump Kit
700HPPK
The Fluke Calibration 700HPPK Pneumatic Test Pump Kit generates and adjusts pneumatic pressures up to 21 MPa (3000 psi), without requiring a nitrogen bottle or other external pressure supply. It supplies pressure to devices under test (DUTs) that include transmitters, controllers, pilots, digital and analog gauges, and more. It’s the perfect solution for generating high pressure in the field, where conditions and operating surfaces can vary. The 700HPPK is the ideal choice for calibration technicians, test engineers, and instrument technicians working in industries like natural gas transmission and distribution, process, aerospace and defense, who need a simple-to-use, safe and portable pressure source that they can depend on in a wide variety of conditions.
-
product
EDFA
SPA-2-4X22-WDM EYDFA
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
product
Component Test Stands
As your specialist for measurement and testing technology, imc designs and manufactures test stands perfectly matching requirements for a complete range of components: whether for servomotors, pumps, brakes or valves – according to your wishes, imc component test stands can quickly and precisely test for perfect operation, verify lifetime, determine energy efficiency, and much more. Thanks to the modern software imc STUDIO, test objects can be tested for complex and wide-ranging scenarios.Test stand solutions from imc are characterized by their flexibility, short set-up times and productive test processes.As a manufacturer of measurement and test technology, it is second nature to us that imc test stands deliver reproducible and verifiable results and ensure productive test processes. Furthermore, we place enormous value not only on first-class technical features for imc test stands, but also on meeting the economic demands of our customers.
-
product
400 HP Complete Bench Hydraulic Test Center
HTC-400
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 400 hp (298 kW) HTC Complete Bench is for the dealer that services components from a predominately medium size machine mix such as large construction equipment (loaders, dozers, excavators).The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
product
Colorimeter
Model CA-600
Teledyne Analytical Instruments
The CA600 is an online sequential sampling analyzer, using colorimetric methods. The analyzer can be configured to most laboratory colorimetric tests in individual processes.The CA600 Analyzers are easy to start up and use, simply connect the sample, waste and reagent lines and then power up the factory calibrated analyzer. Wall mount hardware is standard but an optional bench-top stand with reagent holder is also available. Accessing information for customizing an analysis routine is easily accomplished with the simple, user friendly menu structure and touch screen interface.The analyzer has two separated enclosures with two lockable doors. The top enclosure, called the electrical enclosure, includes the main power supply, the controller PCB assembly and the touchscreen interface. The bottom enclosure, called the liquids enclosure, includes all the components involved in the sample and reagent flow, mixing and reaction stages (sampling pump, reagent micro pumps and colorimetric reaction cell). Numerous analysis configurations can be programmed, depending on the accessories and the number of micro-pumps mounted in the liquid enclosure.
-
product
Low Gauge Vacuum Tester
G4103
Suitable for use on all petrol engines and easily fits to most vehicles. Accurately measures pressures within the range minus 1 bar (30mHg) to plus 0.7 bar (10psi). Applications include: Engine Fault Finding, by using the gauge as an inlet manifold vacuum tester the following faults can be diagnosed: spark misfires, poor engine compression, mixture tool weak or too rich, ignition too advanced or too retarded, inlet manifold and carburettor air leaks, incorrect valve timing. Turbo boost gauge; testing boost pressure up to 0.7bar (10psi) and Petrol Pump Tester; tests electrical and mechanical petrol pumps (excluding high pressure pumps used on fuel injection engines)
-
product
Pump, Hydrostatic Test, 15,000 psi
9901-150L
Hydrostatic test pump may be utilized as a standalone unit or combined with any of our reservoirs, safety test chambers, test fittings or other optional equipment to achieve a complete hydrostatic test system. with integral safety test chamber.
-
product
Spring Testing Machine
This machine is designed to test laminated springs and coil springs. The test is held under laminated springs and coil springs. The Cabinet comprises of the hydraulic unit, the hand wheel of the pump and the release valve handles are outside the cabinet for easy operation. This compact base carrier two fixed upright and four horizontal plates. The first and the third plates with two small uprights from an adjustable frame. The second and the fourth plates are fixed. A square threaded wheel arrangements provided for adjusting the height of the springs.
-
product
PXI-6233, 16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module
779620-01
16 AI (16-Bit, 250 kS/s), 2 AO, 6 DI, 4 Sinking DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6233 is a bank-isolated DAQ device designed for voltage I/O. It offers analog I/O, digital input, sinking digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 24 V signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6233 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6233 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
product
Basic Unit - Medical Equipment Functional Test Module System
GS-X
The GS-X Testing System consists of a Basic Unit and various plug-in test modules which the user can purchase as required. The range of functions of these Module-Box is being continuously expanded, and presently includes functions for testing the following devices: - Infusion pumps, Cardiac pacemakers, Defibrillators, High-frequency Surgical equipment, electrical safety ECG Simulation, Equipment for electro-stimulation.
-
product
Pressure Calibrators
Wherever you need to work and whatever pressure range you need to work with, our broad selection of tools will meet your needs. From pneumatic or hydraulic deadweight testers and test pumps to electronic deadweight testers, bench controllers, and precise analog pressure gauges, we have you covered at the bench. Going into the field? Fluke’s portable pressure calibrators – with or without pumps and intrinsically safe or not – work with gases or liquids, source and measure, power transmitters, and cover a wide range. With individually available pressure modules, our portable and bench solutions cover pressures from vacuum to 10,000 psi.
-
product
thermostats
Cooling bath circulation thermostats - freezing test set of equipment 2 pieces for carrying out the freezing test with 42-2260 .... Complete with insulated connection hoses and connection elements as well as integrated circulating pumps for temperature control of a single or double sample. The temperature setting is software-controlled. For connection, 2 separate fused circuits per 16 A are required.
-
product
Hydraulic Component Test Stand
Model 700
Model 700 Hydraulic Component Test Stand (HCTS). Designed to test heavy-duty, off-highway, closed or open loop pumps, the 700 gives you the capacity to confidently and efficiently verify the quality of your work. Test new or rebuilt pumps, motors, valves, and cylinders independently, and communicate their quality to your customers with the help of PowerNet TD, data acquisition software for transmission and hydraulic systems. Convenient work height with adjustable mounting track. 100, 200 or 300 HP drive motor options available. Variable Frequency Drive (VFD) controlled drive motor. 200 gallon (757 L) high-mount hydraulic oil reservoir for flooded pump supply. Combined kidney filtration and cooling loop for continuous cleaning. Thermostatically controlled cooler and 7 kW reservoir immersion heater.
-
product
500 HP Complete Bench Hydraulic Test Center
HTC-500
The Hydraulic Test Center (HTC) is a versatile machine designed to test heavy-duty, off-highway hydraulic components. The 500 hp (373 kW) HTC Complete Bench is for the dealer that services components from a predominately larger machine size mix such as large mining machines and large excavators. The Complete Bench offers full functionality to test all types of pumps and motors including: transmissions, hydraulic motors, hydraulic cylinders, valve blocks, torque converters, open and closed loop pumps.
-
product
Motor Testers
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test steel casing motor such as pump, fan, air-condition motor, mower, paper shredder and refrigerator etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
PMS Leak Test System
The system (Pressure Measuring System) is a portable, complete system for leak tests. This consist of the pressure test kit PMS3000 for performing leak tests with an integrated graphic-capable 4.3” color touch display and a pressure relief kit DAK2000 for discharge test according to W400-2, Part 16 pressure loss methods as well as DIN EN 805. The system is complemented by a variety of connection accessories like the rugged accessory case (individually equipped), the test standpipe PSR and accessories for building gas connection as well as the electronically controlled test pumps EPP and the compact air compressor KLK1030.
-
product
Phase Sequence Indicators (Contact Type)
862 PR
Standard Electric Works Co., Ltd
● Two functions in one unit: open phase and phase sequence detection.● Neon light indicators.● Large size alligator clips for easy clipping onto switch- boards terminals.● Checks a wide range of 3-phase power sources.● Ideal for installing conveyor lines, pump systems and interconnected drivers.● Waterproof design, protection class : IP24.● Special test leads length are available on request.
-
product
Pressure Comparator (System E)
P014
AMETEK Sensors, Test & Calibration
The P014 hydraulic jack pump (System E) is an extremely effective pressure pump designed for easy, controlled, high pressure generation. Each comparator includes a 4 connection manifold, which can be used for the reference indicator, the device under test, a fine adjust, an isolation valve, or a fluid reservoir. The adjustable reference pressure port lets you set your reference gauge at the best viewing angle.
-
product
EDFA
SOA1550-32(64)
Hangzhou Softel Optic Co., Ltd.
*Single/dual input for choice, built in optical switch for dual input, the switching power can be set by the button in the front panel or by web SNMP.*Output adjustable by buttons in the front panel or web SNMP, the range is down 4dBm*Maintenance function of one-time downward attenuation of 6dBm by buttons in the front panel or web SNMP, to facilitate the optical fiber hot-plug operation without turn off the device*Multi- ports output, can built in 1310/1490/1550WDM.*Standard RJ 45 port for remote control, we can provide output contract and web manager for choice, and also plug-in SNMP hardware can be reserved for update.*With laser key to turn on/off the laser.*With RF test function.*Adopts JDSU or Oclaro Pump laser*Led displays the working condition of the machine*Dual power hot plug power supply for choice, 90V～250V AC or -48V DC
-
product
Fully-Automatic Kjeldahl Analyzer
LD-LKA-C10
Fully-automatic Kjeldahl AnalyzerLD-LKA-C10conducts titration and distillation simultaneously so as to neutralize the ammonia gas released which enhance the test efficiency and avoid the overflow of ammonia. It stand with a measuring range from 0.1 to 200 mgN which gives a maximum recovery of ≥ 99.5 %. The operating ambient temperature of the device starts from 10 °C to 35 °C. 8.0-inch LCD touch screen is used to set the distillation time, the amount of diluent, acid liquor and alkali. Diaphragm pump is used to add reagent so that the injure caused by high pressure pump can be neglected. Wireless network modules is installed for realizing remote data transmission to test data processing and report printing.
-
product
Fuel Injection Pressure Tester
33900
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
product
Autosampling Dissolution Tester with Built-In Sample Collector
Vision AutoPlus & Vision AutoFill
The Vision® AutoPlus™ is a modern upgrade of the popular Hanson legacy AutoPlus™ autosampler. The Vision AutoPlus comes with a choice of 6 or 8 sampling channels, and DissoScan™ (1-bath) or Maximizer™ (up to 3 baths) configurations. Precision syringe pump mechanics, all-inert tubing and valves, and color touchscreen programming with up to 100 protocols are standard on each instrument.The Vision® AutoFill™ is a sample collector designed for seamless integration with the Vision AutoPlus to save space and to provide a 360 degree view for visual monitoring of the collection process.. Vision AutoFill accessories include choice of collection racks with 13 x 100 or 16 x 100 mm test tubes for UV-Vis, 12 x 32 mm vials for HPLC, sample trays with 12 x 32 mm vials for UPLC®, and more.
