Locators
are used to find or position.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 14 GHz
N9936A
-
100 kHz to 14 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
Product
Short Circuit Locator for Power Cables
A910
-
The A910 is a short circuit locator designed for fault location in power cables. The instrument measures the ratio of the resistances of the two sections of failed conductor using a four-wire "Kelvin" connection, thus eliminating errors associated with contact resistances of the test leads. With the A910 you can determine if the cable has more than a short and locate the first and the last fault. The instrument locates fault with an insulation resistance up to 5 Mohms in cables that have a total resistance greater than 5mohm (approximately 90 m of 300 sqmm cable) and less than 30 kohms. The distance to fault is measured as a percentage of the total length of cable and is displayed on a large LCD display.
-
Product
CTDs: Moored
-
Moored sensors measure water parameters in one location over an extended period. These instruments are often battery-powered and save banks of data in their internal memory for later retrieval. Moored CTDs and sensors form the backbone of long-term studies on buoys, docks, and other fixed platforms, providing valuable time-series of data for monitoring and research applications.
-
Product
LAN CABLE TESTER W/ Tone Generator
PA-01T
-
The LAN Cable Tester with Tone Generator is a perfect companion for any network professional. The tester can enhance one’s ability to quickly locate and verify the status of commonly used voice and data cables.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
Miniature Time Code Recorder
MTCR
-
When the distance is extreme or using a wireless microphone is not practical, the MTCR recorder can travel with your subject and capture professional quality audio, synchronized with timecode. It’s tiny size is unobtrusive and easily placed in garments and costumes, and easy to conceal when used as a “plant” microphone to capture environmental or location sound.
-
Product
Chassis - up to Eight 16x1 Solid State 75 Ohm Cable TV Modules or May Be Used to Control a Great Number of 8x1, 4x1, 2x1, or 2x2 Modules
CXAR/256-MF
-
This Chassis is intended to control up to eight 16x1 solid state 75 ohm cable TV modules, or may be used to control a great number of 8x1, 4x1, 2x1 or 2x2 modules. It is often used to control a large variety of custom configurations which may be located in separate chassis.
-
Product
Cable Fault Point Identifier
OCFI
-
Shanghai Tarluz Telecom Tech Co., LTD
Optical Cable Fault Identifier (OCFI) is The latest instrument of optical cable maintenance, repair equipment developed by tarluz, it can identify the physical cable fault location easily. This is an essential tool for fiber optic cable repair!
-
Product
OTDRs And Troubleshooters
-
The FlexScan family of OTDRs automates test setup, shortens test time and simplifies results interpretation - improving efficiency and reducing costs. Integrated light source, power meter, VFL and optional connector inspection tool will ensure technicians have everything they need to locate and resolve optical network issues.
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm 1.0/2.3
45-720A-741
-
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
Endoscopes and Cameras
-
PeakTech Prüf- und Messtechnik GmbH
Is used to locate objects such as connection terminals, electronic components, break points, constrictions, cracks or components at hard-to-reach, hidden locations. This video endoscope camera offers a variety of excellent technical properties, such as the detachable monitor connected by video cable or the high-resolution camera with 6 dimmable LEDs for lighting, which can take photos and videos.
-
Product
Meter Warm-up Board
3000/3001
-
The Catalog 300X Universal Meter Warm-Up Board is designed to go from the shop floor to a customer location. TESCO's Warm-Up Board is made from a high quality industrial fiberglass enclosure and is light and durable. TESCO's warm-up board is the portable, effective solution to your shop, vehicle, or remote meter warm-up needs.
-
Product
Geophone Testing – Hydrophone Testing – Vibrator TestingVersatile Quality Control System - Three Test Units In One!
Bird Dog 3 - 3 Channels
-
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Three different operation with a single unit*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Three-Component Test Mode, checks 3 elements at onceto save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
Product
Metal Box Locator
P500
-
Although originally designed to accurately locate valve boxes and manhole covers, the Elcometer P500 Metal Box Locator can also be used as a general metal detector.
-
Product
Leak Detection Oil
-
The faster, safer and easier way to locate even tiny leaks in industrial air conditioning and refrigeration systems. Lumirati® bottled dyes can be poured directly into any AC&R system. The dye can remain safely in the system to confirm repairs and perform future preventive maintenance checks. Lumirati® Leak Detection Oil is the only dye that gives you all these benefits:- Universal dye that is compatible with all refrigerants and lubricants- OEM-approved by major compressor, refrigerant, lubricant and AC&R equipment manufacturers- Co-solvent free so dye will not impair lubricant properties, which could lead to excessive wear or damage to the system components
-
Product
Transmitters
-
Transmitters by Vivax-Metrotech - cable fault locating, finding holidays on coated pipes, problematic deep-buried lines, long-distance pipe and cable locating, and more.
-
-
Product
Receiver, G12x, 18 Module, with 20" Platform for Tabletop, w/ Left Handle
310104151
-
Receiver, G12x, 18 Module, with 20" Platform for Tabletop, w/ Left Handle Engagement handle located on left side versus standard right hand side Designed for tabletop Includes a 20” platform Equipped with VPC’s Quadratrack™ engagement system 20,000 cycles Handle can be rotated in 90 degree increments Can accept G12x ITA or G12 ITA
-
Product
JEDEC TO Collet Socket
Series 514
-
TO Collet Sockets. Aries TO sockets feature molded chamfer lead-ins for easy device insertion. High stand-off design for heat dissipation and easy cleaning. External polarization for positive location.
-
Product
Analyzer System
Ruggedized Test Systems (RTS)
-
This analyzer is a rugged, field deployable system that detects and locates faults and detects degradation in electrical interconnect systems ranging from simple to complex.
-
Product
Data Loggers
-
For acquiring temperature, pressure or fill levels, use the highly precise long-time data recording devices of the MSX-ilog series by ADDI-DATA. The compact, portable and interference-free systems are ideal for acquiring data at different locations in your installation. Data is automatically converted to physical values and can be calculated via the onboard µ-processor. The integrated web server allows easy configuration, monitoring and data export. Further features: Onboard data saving, internal clock, low consumption and Ethernet interface, data thus being available on the company network for evaluation and statistical purposes.
-
Product
Low Circuit Tester
26250
-
Helps locate shorts or breaks in wiring. Complete with insulated grounding clip.
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
Partial Discharge Testing Equipment
AR700
-
PD Defect Location in High-Voltage Equipment Insulation by Acoustic Sensors To act on deteriorating insulation the source of PD must be known.The insulation defects produce partial discharges, which emits electrical impulses, radiation of electromagnetic waves as well as acoustic signals.The AR700 measures acoustic signals with multiple sensors spread over the transformer. Then the software determines the failure location using the time difference of all incoming signals. Finally, these coordinates are shown in a 3D model of the transformer. AR700 device is used for measuring of acoustic signals on the external surfaces of gas-insulated breakers and substations, power transformers and other tank high-voltage equipment. The acoustic signals are caused by partial discharges in the insulation, which is the sigh of the defects.The advantage of “AR700” device is the quick installation of the acoustic PD sensors on the external surface of high-voltage equipment tank. The sensors have magnetic holder that is why there is no need to de-energize the equipment for the sensors installation. “AR700” device has 4 syn-chronic channels for acoustic signal measurement. This gives the possibility not only to find the defects in the insulation, but also to locate them. The location function of the “AR700”device is unique for acoustic devices.
-
Product
Signal Strength Analyzer
1160
-
Eliminate trips to a site with TESCO’s CAT. 1160 Signal Strength Analyzer. When a meter is not reporting reliably to the Head-end, or for a new meter, concentrator, or antenna installation, TESCO’s SSA will show you the best location for the equipment. Be certain that your antenna placement is in the best location. The SSA actually joins the network, locates and analyzes all the neighbors, and provides a visual indication of the relative signal strength, quality, and throughput of each of them.
-
Product
PMC-to-PCI Express Adapter (PCIe/PCI-e)
5243
-
Our PMC-to-PCI Express Adapter (PCIe/PCI-e) 1X (5243) permits the use of a single-wide PMC module in a 1x PCIe slot. The A and C rows of a 96-pin DIN connector, located toward the rear of the board, connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card.
-
Product
High Power Fiber Optic Visual Fault Locator
VFL-700
-
Shanghai Fibretool Technology Co.,Ltd.
The VFL-700 is specially designed for field personnel who need an efficient and economical tool for fiber tracing, fiber routing and continuity checking in an optical network during and after installation.
-
Product
Noise Monitoring System
Harmony
-
A system that consists of automatic noise measuring device, transmission device, computer system, and operation analysis software, and provides accurate data necessary for establishing noise-related policiesby providing real-time information such as noise level, location, and device status for each branch.
-
Product
Remote Support
-
We have remote support solutions to help you with software and station maintenance, when you are located across the country or even when you are across the globe. ARC’s commitment to quality and service allows us to be responsive to your needs. We can offer remote software installation support, standby support during critical OS upgrades and other remote service packages to keep our customers on track.
-
Product
Cable Fault Location System
Syscompact 2000 M Pro
-
Cable fault location system 2000 M pro. The portable BAUR Syscompact 2000 M pro cable fault location system is used for cable fault location and cable testing in low- and medium-voltage cables up to 65 km length.* Fully integrated proven cable fault pre-location methods* Surge mode for acoustic pin-pointing* Easily transportable* Ideal for locations that are difficult to access
