Locators
are used to find or position.
-
Product
Hi-Definition Video Inspection Station
VIS800
-
Video Inspection Stations are available with?or without on-screen measurement capabilities?and offer?an excellent way to evaluate or test small works or items in?difficult to access locations.? As todays electronic and mechanical systems keep getting smaller, it becomes impossible to test or measure these products with traditional methods. For many applications, from development to production testing, video based inspection can help maintain quality control. Many of these systems are used in labs for development or used in production for testing production samples.
-
Product
PCI Express-to-XMC Adapter
4876
-
The Technobox, Inc. P/N 4876 PCI Express-to-XMC Adapter is a development/diagnostics tool that permits the testing of a PCIe card in an XMC site. Up to 8 lanes are supported via the P15 connector. Several activity LEDs located at the edge of the board give an indication of key XMC and PCI Express signals and voltages.
-
Product
Water Level Recorder
MIDAS WLR
-
Designed for long or short-term deployments in offshore environments, or locations where a traditional shore-based tide gauge is impractical, the MIDAS WLR can be moored in line or to the seabed.
-
Product
Surge and Test Generator
STG 600
-
Cable fault location with the BAUR STG 600. The STG 600 surge and test generator is a multifunctional cable fault locator for low voltage networks. The surge and test generator is used for cable testing as well as for precise location of high-resistive and intermittent faults in low voltage cables.* Specifically for use in low-voltage networks* High surge energy: 600 or 1000 J** Light, compact and transportable* Single systems for cable testing and faults location
-
Product
External Temperature-40 to +125C
TGIS-0020
-
This model is battery powered and measures temperature using an external probe, providing cost-effective environmental monitoring ideal for inaccessible locations or where a faster response time is required.
-
Product
Cable Fault Locator
TX2002
-
Lowest Cost Full Specification Professional Graphical TDR Rugged Palm Top Design 350g (12oz) 5 Measurement Ranges up to 3500m (11,500ft) 50, 75 & 100 ohm Selectable Cable Impedance Built in Tone Generator for Pair Tracing & Identification Suitable for testing all Communications Cables Water & Dust Proof to IP54 Complete with tool-belt holster & test leads
-
Product
RF CAPTURE & PLAYBACK SYSTEM
WEIVER 2.0
-
With Weiver 2.0, you can capture worldwide broadcasting standards of DTV (FM, AM, ATSC, DVB-T/H, DVB-T2/S2, DVB-C, DMB, CMMB, DTMB, ISDB-T/B, OpenCable, and ATSC-M/H). Also, you can capture radio broadcasting ATV (NTSC, PAL), RDS, TMC, LTE, and Wifi. Weiver is equipped with a GPS module for accurate location information to evaluate the strength of the RF signal. Basically, you can capture any live signals and then playback wherever and whenever you need to.
-
Product
Ultrasonic Level Transmitter
USonic
-
The Drexelbrook family of Ultrasonic technology level products offers an affordable two wire and line powered version for non-contact level measurement of liquids and slurries for level, distance, volume and open channel flow.Measurements of level, distance, volume and open channel flow is easily configured through the menu driven display. The Usonic level transmitter is offered with a two wire 4-20 mA, Hart output signal and is suitable for all Class I Div. 1, Zone 0, I.S. or XP locations. The bench configuration eliminates the need to move process material levels for calibration.
-
-
Product
PCI/PDXI/ISA Boards
-
United Electronic Industries, Inc.
For PCI bus16 analog outputs, 16-bit resolution8 digital input lines, 8 digital output linesThree clock/interrupt lines, three 24-bit counters/timersChannel list (64 locations)Independent waveform on each channelSimultaneous channel update; update on external event2k samples onboard buffer size (upgradable to 64k samples)
-
Product
Field Comm Analyzer
S5800H
-
S5800H Series Field Comm Analyzer is an 8.4 inch large touch screen instrument which is designed specifically for wireless communications field engineers and technicians. S5800H series provide all necessary measurement functions and performance to accurately characterize the signal environment in addition to clearing, detecting, identifying and locating signal interferenc.
-
Product
Ground Grid Tester
GGT Series
-
The GGT500 ground grid integrity tester is designed for inspection of the substation ground grid. It can also be used as a portable micro-ohmmeter with Both Sides Grounded and Remote Control functionalities. It is intended to inspection the conditions of a grounding system beneath substations, testing of medium- and high-voltage circuit breakers, disconnecting switches, high-current bus bar joints, cable splices, and different high-current links.In the United States when inspecting the quality of the grounding systems beneath a substation, the proper procedure is to inject 300 A DC during a time period of 60 s. This is what the GGT500 will do, and in that time period, the current path and voltage drop are checked. Also acting as a micro-ohmmeter, the GGT500 can test low resistance values by producing high test currents of up to 500 A.The instrument is placed in an unbreakable, plastic case with IP67 protective rating (with closed lid). Although very portable and lightweight, micro-ohmmeters have very high output power capabilities. High output voltage enables a wider measurement range at higher test currents, as well as the use of thinner/longer test cables. GGT500 ground grid integrity tester generates a true DC ripple-free (less than 1 % ripple) current with automatically regulated test ramps. This significantly decreases magnetic transients and ensures great accuracy.When used for testing in Both Sides Grounded conditions, a special current clamp powered from the ground grid integrity tester is used for measuring a current through groundings. If even a higher safety level is required, the remote control feature enables the operator to perform measurements from a distant location, away from the instrument and test object.
-
Product
Board Fault Locator
SYSTEM 8 (BFL)
-
The SYSTEM 8 Board Fault Locator provides the user with the ability to functionally test all common digital ICs in and out-of-circuit. A combination of industry recognised test techniques provides a high level of fault coverage. Additional tools are provided by the SYSTEM 8 Premier software to further enhance the unit\'s wide range of applications.
-
Product
FieldFox Handheld Microwave Spectrum Analyzer, 26.5 GHz
N9938A
Spectrum Analyzer
100 kHz to 26.5 GHz frequency range Expand capabilities with optional tracking generator, interference analyzer, built-in power meter, and more Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Locate interfering signals using the intuitive spectrogram display and recording capability Easily measure average and pulse power with a USB power sensor, pulse measurements with time gating Lightest microwave handheld spectrum analyzer at only 6.6 lb. (3.0 kg)
-
Product
HDMI Matrix Switch Over HDBase-T with Power Over Ethernet (PoE)
SM-8X8-C6HDR-POE-HDBT
-
The VEEMUX® HDMI Matrix Switch Over HDBase-T with Power Over Ethernet routes and distributes uncompressed HD 1080p, multi-channel audio, Ethernet, and IR from eight HDMI video sources to eight displays via inexpensive CAT6a/7 cable using HDBase-T technology. Power over Ethernet provides power to receivers that can be located up to 328 feet away.
-
Product
DC Earth Fault Locator
GFL-T + GFL-R
-
The DC Earth Fault locator is suitable to test the DC Battery System and Trace Ground Faults. The system is suitable for Power Plants, Sub-Stations upto 765KV and other industries. The system is highly capable in tracing and pin pointing the DC earth faults in a live system without requiring any shut downs. The receiver sensitivity of 1mA and better is capable to trace most complex fault.
-
Product
CBRN Detectors
Static Radiation Detectors
-
A static (or fixed) radiation detector is a device that monitors radiation in a single location. They are often used in areas of national security, such as airports, railways, and ship terminals.
-
Product
Leak Detection System
-
Leak detection system (LDS) is a state-of-the-art software and hardware suite intended for leak detection in long-distance and oil products pipelines, calculation of leak location and evaluation of its intensity in constant full-time mode. The system allows to detect leaks in stationary and non-stationary pumping modes without gravity mains as well as in suspended pumping mode.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Cable Fault Locator ECFL 30
ECFL 30
-
Compact precision active/passive, AC/DC bridge with dual channelTDR for fault location on balanced loaded and unloaded cables.
-
Product
E1 Testers
-
GAOTek provides a large collection of high quality, affordable E1 testers that are specially manufactured to speed up the ethernet maintenance time and work efficiency for sale to the United States, Canada and Globally. These devices consist of PING, router trace, a port location tool, a loop-back tool and offers a variety of Ethernet diagnostic functions. These E1 Ethernet test instruments are all incorporated with test tools for E1, V port, and Gigabit Ethernet link repairs, and failure diagnosis. E1 Ethernet testing devices are user-friendly, can be used in Ethernet cable tests, flux error code tests, connectivity performance, traffic testing, ethernet wire testing, and bandwidth verification. As these devices help in measuring and proving performance for criteria Ethernet networks they are commonly used in the RFC2544 performance test.
-
Product
Pathfinder Locating System
The STICK™
-
Built with Pathfinder SAF Technology™ at its core, the Stick offers RYCOM’s most ophisticated technology in an economical package. Pathfinder SAF Technology™ is the heart of our premium locators, now RYCOM is applying this proven technology throughout the entire product line. From crowded easements, to long runs of pipe, to the most demanding of locating environments, users can depend on The Stick. Dependability is not only driven by the internal technology, but The Stick is built to last with an aluminum housing and sealed against weather. The ruggedly designed and well balanced receiver includes an LCD screen providing relative and actual signal strength, as well as a speaker for variable audio pitch. A peaking signal response allows the user to minimize interference and maintain the locate on the target conductor. The Stick cable and pipe locator offers multiple active frequencies — from 50Hz to 82kHz — ensuring flexibility to match the needs of the most complicated locating environments. Transmitter functions include transmitter induction, coupler induction and direct connection. Whether the locate is measured in feet or miles, with automatic impedance matching from 5 ohm to 25,000 ohms and 3 watts of output power, The Stick will meet the challenge. Rycom Instruments®, Inc. locators are designed and manufactured to make utility locating as accurate as you need and as simple as you want.
-
Product
Electronic Stethoscopes
-
Electronic Stethoscope Standard Headphones are designed to help locate the source of excess bearing and machine noise easily at low cost, it is an ideal easy to use listening device for mechanically generated noise in all types of applications, the 3.5mm jack socket tape output can also be fed into an audio tape recorder to store the data for either further analysis or as a reference for future comparison.
-
Product
E-beam Metrology And Inspection
-
Our HMI e-beam solutions help to locate and analyze individual chip defects amid millions of printed patterns.
-
Product
Radio Interception & Direction Finding Systems
-
Net Radios are used by many organisations including anti-national elements, and it has always been a cause of concern for the LEAs. Stratign provides solutions for interception, demodulation and decoding of HF/VHF/UHF communications with the capability of finding the actual location of the transmitters.
-
Product
Wi-Fi Performance Validation
-
Excentis offers a unique testing service in a real home a realistic, static, residential environment with controllable interference. This setting enables the customer to statistically compare Wi-Fi access points, as the performance is measured by a robot from different physical locations in the home, with different client types (laptops, tablets, smartphones,...) and with different operating parameters. This program can also be used for benchmarking.
-
Product
ESM/ELINT System
-
Shoghi’s Electronic Support Measures (ESM) are designed for electronic warfare techniques involving actions to detect, intercept, identify, locate, record, and/or analyze sources of radiated electromagnetic energy for the purposes of immediate threat recognition.
-
Product
Universal Counter
U6220A
-
The Picotest U6200A also provides great features including Frequency & Ratio (11Digits/Sec.), Time interval, Period (2.5 ns to 1000s), Duty Cycle, Pulse Width, Rise/Fall Time, Peak Volts (100 Hz~300 MHz), Phase, Totalize, Temperature Stability (< 1 PPM), Aging Rate (< 2 PPM per year), timebase reference channel (Figure-2) and complete Front-End Isolation. Moreover, it offers 20 memory locations (Figure-3) for storing frequently-used operations.
-
Product
High Density 68 pin
HDEterm68
-
The high density 68 pin SCSI II/III connector is being used for purposes other than SCSI interfaces because of board and front panel space limitations. For example in the PMC environment the SCSI connector provides an excellent size and pin count for the front panel space allowed. The SCSI connector while dense, is not easy to connect to with wiring intended to go to multiple locations
-
Product
Ethernet Media Converter
MC-E Series
-
The MultiLink MC-E series makes it easy to use the power of optical fiber for extending Ethernet networks to remote locations. The fiber port is available in a variety of connector types and can support extremely long distance connections of up to 40km. With a built-in 2 copper port switch, it's also the fastest way to add multiple Ethernet drops to remote locations.
