Filter Results By:
Products
Applications
Manufacturers
Systems
are interconnected groups of purpose.
See Also: Equipment, Test Systems, System Integrators, System Test
-
product
Mezzanine System
5658
ECM P/N 5658 provides eight channels of 16 bit current measurement in the 0 to 25 milli-amp range. Each channel allows independent common mode voltages from -100 volts to +100 volts. Current detection is accomplished with a precision 100 ohm current sense resistor, creating a voltage drop of 2V in the current loop at 20 milli-amps.
-
product
ESS Performance Test System
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
product
VME Data Acquistion System
ADM-31
The VME-based ADM31 data acquistion system supports up to 48 differential or up to 96 single-ended analog inputs. The ADM31 control card is an intelligent A/D subsystem master or slave device that controls the analog A/D cards. Up to two A/D cards can be configured with the control card to complete the A/D system.
-
product
Real-time X-ray Inspection Systems
JewelBox Series
JewelBox x-ray inspection systems feature ultra-high resolution, powerful microfocus x-ray tubes, five-axis, and positioners. The JewelBox Series is divided into three broad categories: JewelBox 70-T, JewelBox 90-T and Ultra Compact each of which can be customized for specific applications.
-
product
Automatic Test System
Star-Rec
Test entire HDI panel at once, or step & repeat in the "feed" direction. Fastest BGA Strip test system available. Star-Rec comes standard with: * loader * board cleaner * CCD Camera Alignment * electrical test section * fail and pass re-stackers * Board Marker
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Manual Semiconductor Metrology System
Front USB port enables easy storage of measurements and other data to flash drivesMTI Instruments’ Proprietary Capacitance Circuitry for Outstanding Accuracy and DependabilityNon-contact measurements76-300 mm diameter wafer rangeOptional wafer measurement ringsWafer stops for exact centeringEthernet interfaceFull remote control software (Windows compatible)Optional calibration wafers
-
product
Low Cost Splitter Systems
RATCAT Family
The CAT Snake Stage Box allows four lines of balanced analog audio to be run down a shielded CAT5/6/7 cable. Each of its four channels can carry balanced analog, AES/EBU, DMX, and Clear-Com signals hundreds of feet away. The CAT Snake is a fully passive unit which can be input directly into analog or digital consoles. Each channel is isolated which means channel 1 can send a DMX Signal while channel 2 is sending balanced analog all down the same shielded CAT5 cable. Multiple CAT Snake stage boxes can be daisy chained to allow the same four analog channels to be dropped in multiple locations. Each CAT Snake stage box has an Ethercon input and Ethercon parallel output that allows the CAT Snake to be used as a hard-wire split.
-
product
System Level Test
SLT
As technology nodes continue to evolve and with a more aggressive time to market to bring devices to their end applications, full test coverage of such chips is possible only with System Level Testing.
-
product
High Voltage, Continuity & Hipot, Cable & Wire Harness Test Systems
CableEye HVX, HVX-21
Fast ● Simple ● Precise
Advanced wiring analyzer scans for continuity (opens, shorts), miswires, resistance, capacitance, components (resistors, diodes, LEDs, capacitors) dielectric breakdown, insulation resistance, intermittent connections
HVX (Item 829) 1500 Vdc, 1000 Vac
HVX-21 (Item 829A) 2100 Vdc, 1200 Vac
For diagnostic and Pass/Fail Testing — Permits expanded testing (compared to models in our low voltage product line) for insulation resistance (IRI) and dielectric breakdown (DWV).
All CableEye testers are suitable for production, fault diagnosis, QC (Quality Control), assembly, and prototyping of standard or custom cables. Each combines test, fault location, design, documentation, labeling, and database storage in one instrument. Tests can be performed on long cables (with or without connectors) or no cables (e.g. connectors, backplanes, PCBs, components).
Standard Features & Benefits:- USB certified, PC-based tester for a versatile, fast, robust system with long life-cycle.
- Multilingual, dynamic, graphic-rich display (netlist & wiring schematic) provides clarity and speeds diagnostics.
- 128 Test Points, expandable to 1024 providing flexibility as your product line changes.
- User-selectable voltage to each connection group in the cable simplifies an otherwise complex process, accelerating testing.
- Programmable Ramp Up, Ramp Down, Dwell Time (same as Test Time), Trip Current, and Trip Delay (same as Soak Time) adds versatility.
- Current leakage detected during HV test phase provides a measure of insulation resistance up to 1 GΩ (HVX) and 5 GΩ (HVX-21) - any leakage current exceeding a preset limit reveals the presence of moisture, flux, or other contamination on exposed contacts.
- Real-time screening for intermittent connections for pinpointing elusive faults and improving quality.
- Automation scripting in a simple, intuitive language allowing non-programmers to reduce operator error by automating repetitive steps.
- Pop-Up Work Instructions. choose the exact amount of detail, imagery, language and automation you need to ensure your work instructions and tests are carried out flawlessly.
- Flexible tolerancing: optionally define as percentages or absolute terms, as well as asymmetrically (e.g. +0%/-10%) for improved yields.
- Barcode-tracking & archival data-logging to achieve error-proof test process and improved traceability & productivity.
- Print PASS/FAIL labels, test reports (with or without color wiring schematics/netlists) and log reports to satisfy ISO9000 reporting requirements.
- Compatible with laptop and touchscreen PCs for fieldwork and rack/off-bench mounting.
Includes:
CB29 board set (Item 759) for bare wire connections; comprehensive PC software with Database of >200 standard cables; 2 yr Product Support Subscription comprising Warranty, free tech support, and free software upgrades.
Select Add-On Options:
Hardware: 128-point Expansion Modules (attach to base); 4-Wire Kelvin Resistance Measurement, 1 mΩ at 1 A; Advanced Measurements; External Measurement Instrument Port (e.g. 10 GΩ Isolation at 100 V); Remote Control Connector for Deadman Switch; Environmental Sensor
Software: PinMap™ fixture editor, Connector Designer™ connector editor, or Autobuild™ guided assembly modules
camiresearch.com |@CAMI_CableEye |+1.978.266.2655 -
product
Automatic Coil Test System
LM Series
Koyo Electronics Industries co., ltd
Models in LM-2100 series equipped with LCR meter are designed to measure inductance and dissipation factor of the coil to which DC current is superimposed. Special circuit is built in to protect the LCR meter from surge voltage. Applied current can be step by step in the remote mode. Voltage application is impossible with the safety cover open.
-
product
Lightning Detection & Early Warning System
EWS-PRO
The EWS-PRO is the only professional grade portable lightning detection and early warning device available today. It is a self-contained instrument with the electronic sophistication to detect lightning strikes over 40 miles away, and to accurately track a storm's approach with both its audible horn and its large LED visual alerts.
-
product
Resistance System Kit
PMK-151
The PMK-151 Basic Measurement Kit has all the functionality of the PMK-152, but adds computer downloading capabilities. It contains all the instruments you need to take a variety of resistance measurements.The PMK-151 includes Prostat's PRS-801 Resistance Set with modified 5 pound conductive rubber electrodes, the PRS-801 wide range resistance meter, and Prostat PRS-801 Connectivity software for computer data downloading. You can take measurements at 10 and 100 volts with accuracy within ±5%.
-
product
Eddy Current Probes and Drivers
Proximity sensors work on the eddy current principle. A proximity system consists of an eddy current probe, extension cable and driver. A high-frequency RF signal is generated by the driver, sent through the extension and probe cables and radiated from the probe tip. The tip consists of a precision wound copper coil inside a chemical and temperature resistant PEEK case.
-
product
Short Circuit Test System
Shanghai Guantu Technology Co., Ltd.
The short-circuit test system refers to what kind of short-circuit test is carried out by which equipment, and how long is the test time. But I have one thing to tell you, the short circuit test is a kind of destructive test, mainly to test the working condition of the used equipment in a crisis situation, or to test how strong the anti-destructive ability of the used equipment is. Just like a lot of equipment in the military must undergo a short-circuit test, some for 3 minutes or longer, in order to resist breaking calls against the enemy during wartime.
-
product
Portable Appliance Tester
PAT-10
The innovative combination of small dimensions (full portability of the device) with advanced measuring systems allow to carry out fully automated measurements for electrical equipment, IEC cables and extension cords (including those with PRCD). The set of tests is performed with one click of START button. Configuration options of the meter allow you to modify the operation of the device, and thus, tailor it to the needs of the user. In situations, where it is necessary to perform simple and single measurement, without the need to do complex measurement procedure, Pat Sonel allow you to work in a single measurement mode of a given type (ie. Manual). All meters in this series (Pat) also allow you to make basic measurements without external power in emergency situations i.e. in the absence of the power one can easily run a simplified set of test in a battery mode. Small size, weight, and specially designed carrying case of the meter and accessories provide comfort and high mobility. Wireless communication with a printer enables organization of the working site without the hassle of unnecessary cables. Storage and integration of the results in PC software further extends the functionality of the instrument.
-
product
PXI 32x8 Matrix Module, 2-Pole, 2A, 60W
40-580-001
The 40-580 is a 256 crosspoint PXI matrix with dual pole switching. The module consists of a 32x8 matrix of 2-pole electro-mechanical relays with 2A current handling. The module is designed for switching medium voltage and power signals, typical applications include signal routing in ATE and data acquisition systems. The user signal connection is via a robust 160 pin DIN 41612 connector that is fully supported by the wide range of Pickering Interfaces cable and connector accessories.
-
product
LXI Microwave Multiplexer, SP6T, 7-Bank, 67GHz, 50Ω, SMA-1.85
60-800-807
Our 60-800-807 is a 7 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
product
LXI High Density 256x4 Matrix - 60-551-024
60-551-024
High-density single pole matrix module capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
product
Miniature Electrodynamic Shakers
Miniature electrodynamic shakers are small, portable units designed to simplify your vibration testing needs. From the SmartShaker™ with an integrated amplifier, to an Inertial Shaker System for testing in hard-to-reach areas, mini shakers offer flexibility when testing. Miniature shaker systems range from 2 lbf (9 N) to 7 lbf (31 N) sine peak force excitation.
-
product
Satellite Clock
TCG 01-G
The TCG 01-G is a highly accurate, full featured GPS and GLONASS (GNSS) clock. With enhanced cyber security features that support NERC CIP requirements, the TCG 01-G is designed for use in modern day smart grid / smart substations, electricity distribution, transmission, generation protection and control systems. The clock synchronizes multiple IEDs (Intelligent Electronic Devices) within a network, including protection relays and remote telemetry units to enable accurate time stamping. The TCG 01-G supports IEEE 1588 v2 (PTP) and IEC 61850.
-
product
Bridge Coordinate Measuring Machines
Measurement results with high accuracy are particularly important for quality assurance. Bridge coordinate measuring machines from ZEISS have a precise probe system that convinces with high measuring speed. The various solutions and systems can be tailored directly to individual requirements.
-
product
Pressure Calibration Custom Systems
Our custom systems integrate standard Fluke Calibration products, pressure generation and control accessories and/or data acquisition hardware to meet customer requirements. Systems may be mobile calibration carts or rack mounted instrument panels or benches. 7250-sys Ruska gas pressure controller system, and engineered systems customized to fit your application needs.
-
product
Watchdog Timer and System Monitor Card
PCIe-WDG-CSMA
This multifunction Low Profile x1 PCI Express card contains a watchdog timer used to monitor the operation of your application program and operating system to initiate a system reset in case of a lockup. It can also monitor and control a variety of system hardware parameters. The card is 6.6 inches long and 2.535 inches seated height. I/O wiring connections are via a female DB25 connector on the card mounting bracket. Two models with increasing features are available.
-
product
Aluminum Portable Telemetry System with Integrated Keyboard and Display
LS-84-AP
The Lumistar LS-84-AP Rugged Aluminum Portable Data Unit offers a low cost, high performance COTS solution for aportable quick look ground station. Lumistar LS-25 FMReceivers or LS-25-D2 Down Converters with LS-35-R Multimode IF Receiver, Bit Synchronizers and Multi-function PCM Decommutators, and LS-71D/A Converters can be installed inthis rugged high quality portable computer and bundled with theLumistar setup, control, and monitoring software to achieve anaffordable alternative to the often expensive, proprietary architecture products of other suppliers. The flexible design allows the user to define the desired data acquisition cardconfiguration to unique requirements.
-
product
Spatial Laser Measurement
Our laser systems for mine and quarry scanning, vessel-mounted waterway scanning, land-based mapping applications and marine dynamic positioning have been developed over many years of close work with those in the field, and have been adopted widely due to their reliability and ease of use.
-
product
High Speed Camera Systems
MEMRECAM MX
The nac MEMRECAM MX is a robust, turnkey solution for multi-camera onboard and offboard automotive testing and occupant safety applications. Each system supports up to eight, tightly synchronized camera views, and integrates seamlessly with all current and legacy MEMRECAM imaging systems.
-
product
High Temperature Diametral Extensometers (1000 C)
Model 3580
Jinan Testing Equipment IE Corporation
This model is for diametral strain measurement with furnace and induction heating systems. Quartz rods and water-cooling allow the unit to be used for high temperature testing of metals, ceramics and composites. With induction heating, this model often can be used without water-cooling. When used in furnaces, the extensometer is often mounted directly to the furnace side cut-out. Optional load frame mounting brackets are available for supporting the extensometer in cases where furnace mounting is not possible. These optional mounts are used with induction heating or furnace systems. The Model 3580 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
product
Panel for Energy Monitoring
Energy Box
The box allows a quick installation of the energy monitoring and remote control system Ducknet
-
product
Data Acquisition (DAQ) And Real-time Control Systems
Our data acquisition devices are capable of storing hundreds of analog and digital channels at full speed while allowing in parallel data to be sent out in real-time to any 3rd party EtherCAT master controller. We have brought the worlds of data acquisition and real-time control closer together which will save you time and money in a big way.
