Verifiers
-
Product
Resistivity Meters
-
Periodic compliance checks of ESD work surfaces are super important. Monitors only verify the ground plane, or path to ground. The surface itself can wear down, become dirty, or if you use low quality mat—just not hold up. A handheld Surface Meter is great for running monthly, or prescriptive compliance verification of your ESD surfaces.
-
Product
CAT IV 600 A TRMS Navigator Clamp Meter
ACD-50NAV
-
ACD-50NAV clamp-on power meter offers AC current measurements to 600 A, AC/DC voltage to 1000 V, and wide jaws to accommodate large conductors. This clamp-on multimeter is ideal for industrial power monitoring and verifying system conditions.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 131k Ohm
50-294-034
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Resistor Card 2-Channel 2 Ohm To 131 Ohm With SPDT
50-293-134
Programmable Resistor Module
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Dial Wrenches
-
A dial torque wrench is an essential tool in torque measurement, as it provides quality control in regards to monitoring and verifying torque. This tool is commonly used to test, audit, and verify torque applied to joints. Using the memory pointer, the dial torque wrench will capture finishing torque that is applied to any fastener.
-
Product
Trailer Buddy 4/5 Pin One Man Trailer Wiring Tester
220
-
*Tests 4 & 5 Pin Flat connector wiring *Each signal from vehicle emits a unique tone *Loud beep can be heard over shop noise *One person makes complete test in 30 seconds! *Just apply brakes, turn signals, running lights& engage reverse *Tester also emits unique tone for any shorts in the wiring! *Greatly reduces time spent verifying vehicle trailer wiring *Very simple & easy to use - saves time!
-
Product
2.5mm Test Rod Test Probe Needle
CX-4C
-
Shenzhen Chuangxin Instruments Co., Ltd.
2.5mm test rod test probe needle Used to verify the protection of persons against access to hazardous parts.
-
Product
PXI Resistor Module 4-Channel 1R to 255R with SPDT
40-293-113
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PNA-L Microwave Network Analyzer
N5232B
Network Analyzer
Perform basic analysis of passive components and simple active devices Measure S-parameters with good accuracy up to20 GHz in cost-sensitive applications Get the world's best price-to-performance ratio for microwave manufacturing Configure an economical solution for signal-integrity measurements and materials characterization Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 2.04k Ohm - SPST
50-294-122
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
8 Series Optical Clock Recovery
-
The 8 Series Optical Clock Recovery is a fast, flexible and reliable instrument for assisting in the validation of current and future optical designs. With all the applicable standard rates in the 26 and 53 GBd data rate ranges – no options required – the TCR801 Optical Clock Recovery is a crucial component for any bench or rack aimed at verifying the latest high-speed optical standards. Featuring quick lock capabilities and a sensitive front end for low power signals, this instrument simplifies the challenges associated with today’s optical testing.
-
Product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Video Line Insertion Processor
VIP472
-
The VIP472 is a line switcher that will insert any one video test signal line onto your NTSC video path so that you can monitor the trasmission signal quality. This process allows the video test signal to pass through all digital compression systems to verify that your video is being delivered accurately without distortion.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
Product
Safety / Area Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic provides general purpose, small object and slim body Area Sensors for detection of intrusions and parts, edges of moving or falling objects and to control access. These compact and ultra-slim picking Sensors with easily visible job indicators verify picking of parts in cell production and assembly line.
-
Product
PCI High Density Resistor Card 6-Channel, 24-Bit, 0 To 16M Ohm
50-295A-121-6/24
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
