ANSI
-
product
Fume Hood Monitor
FHM10
Fume hoods are a primary source or protection in laboratories. Face velocity measurements are often used to gauge the performance of a fume hood’s ability to contain and exhaust hazardous chemicals. By accurately measuring face velocity and alarming on unsafe conditions, TSI’s FHM10 Fume Hood Monitors provide a high level of fume hood safety. And, the FHM10 helps users comply with standards and regulations set forth by OSHA, NFPA, ANSI Z9.5, and SEFA, calling for monitors to be installed on fume hoods.
-
product
SIMULATOR
458-LM-A8-36
Simulates 26 AWG PIC as specified in ANSI T1.417Bandwidth DC to 36 MHzIdeal for testing ADSL, ADSL2, ADSL2+, VDSL, VDSL2 modems/DSLAMs8 channels per line moduleLoop lengths programmable from 0 to 7,500 ft in 500-ft incrementsPlugs into our 458-CC-16 (16-slot chassis) or 458-3SLB (3-Slot chassis)Noise Floor less than -150 dBm/Hz
-
product
Active Loop Antenna
AL-130R
Also known as Magnetic Loop Antenna, the AL-130R is compliant with CISPR 16-1-4. It is ideal for emissions measurements as required by various EMC standards such as FCC 18, CISPR 11, CISPR 13, CISPR 14, CISPR 32 and many more. The built-in, low-noise preamplifier, increases overall measurement sensitivity as well as the overall signal to noise ratio. As per ANSI C63.4-2014, the use of active loop antenna for compliance testing is permitted in a non-sheilded environment ONLY if the saturation indicator is continuously monitored during the course of testing. Com-Power’s Remote Antenna Interface (RAI-100) comes in very handy for this application. It is a compact controller which can be used to enable/ disable RF measurement circuit and monitor saturation and battery low conditions remotely via a fiber optic cable up to 30 mtrs in length.
-
product
MIL-STD-1553 PMC Interface Module
PMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
VPX
VPX, formerly known as VITA 46, is an ANSI standard (ANSI/VITA 46.0-2007) that provides VMEbus-based systems with support for switched fabrics over a new high speed connector.
-
product
MIL-STD-1553 XMC Interface Module
XMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurations - Transformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating availableDesigned for extended temperature operations - x1 Lane PCI Express Host Interface - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Power Frequency Transducer
PP1S
1. Measuring and conversion IEC 6882. Dielectrical strength IEC 688 4 KVac / 1 min.3. Impulse test ANSI C37.90 / 1989 IEC 255-3 5KV ( 1.2 x 50 us ) 3KA ( 8 x 20 us ) - current coil4. Surge test (ring wave) ANSI C37.90 / 1989 ( 3KV - 0.5us / 100KHz ) IEC 255-3 ( 2.5KV - 0.25ms / 1MHz )5. Adaptability for power system VDE 0110 6. Measuring reliability VDE 3540
-
product
RF Transformers
Pulse continues to lead the way with a broad range of components that enable twisted-pair copper high-speed services to homes and businesses. Pulse components are also used in cable modems and the consumer electronics that provide home networking services. Our high-performance transformers support home phone line and power line networks. These transformers are designed to exceed ANSI and ETSI standards, and have excellent THD performance and small footprints.
-
product
Portable Bar Code Verifier
Inspector Model D4000 Auto Optic
The Model D4000 Auto Optic provides ISO 15416 and ANSI X3.182 Method. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a laser scanner (either in a single piece or connected with a cable). Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple four-button user interface. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
product
Single Phase Round Energy Meter Test Bench Type KP-S1000-C
Bofa Instrument & Equipment Co., Ltd
Single phase round energy meter test bench, type KP-S1000-C, is a special calibration equipment for testing Round (ANSI Socket type) energy meter and normal energy meter with bottom terminal block. It is an ideal testing equipment for energy meter factory or R&D institute, especially for testing ANSI Socket type energy meters. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
product
Powered VXS Crates
VXS - "VME-bus switched serial" is the new ANSI / VITA 41 standard which combines the 32-bit parallel VME-bus with high speed switched serial interconnect fabrics in order to increase the data transfer bandwidth to several GB/s.
-
product
Tracer Gas Diffuser Kit
DIF-KIT
The Kanomax tracer gas diffuser kit is used in performing tracer gas tests in accordance with ANSI / ASHRAE Standard 110. The diffuser is designed to the specifications of standard drawing #110-83M.
-
product
Normalised Site Attenuation
NSA
Normalised Site Attenuation (NSA) is measured in accordance with CISPR 16-1-4 and ANSI C63.4 in semi and fully anechoic environment.
-
product
ANSI Meters
Shenzhen Star Instrument Co., Ltd.
Directly connected emergy meter measures active, reactive and apparent energy by multi tariffs while recording max demand and events. It has an optical port and supports RF/PLC communication, which complies and ANSI standard.
-
product
PXIe-4340, PXI Displacement Input Module
785068-01
The PXI Displacement Input Module supports 4-, 5-, and 6-wire AC linear variable differential transformer (LVDT) and AC rotary variable differential transformer (RVDT) measurements. The module simultaneously samples each analog input and sets the excitation frequency and voltage for each channel independently. You can set different timing, triggering, and sampling modes for each channel independently. Diagnostic features include self-calibration, overcurrent detection, and open coil detection.The PXI Displacement Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Active Monopole Antenna
AM-741
The 41 inch Monopole antenna is required for making electric field emission measurements below 60 MHz per Military standards (MIL-STD-461) and FAA (DO-160) specifications. This antenna is for emissions measurements only. It cannot be used for transmitting. The Active Monopole antenna is generally used in a shielded room or in a screen room, with the equipment under test (EUT) placed on a metal ground plane. The 41 inch rod and the ground plane behave electrically as though a mirror image of the rod were located below the ground, and the ground removed. Since the stainless steel plate does not have enough surface area to mirror the entire 41 inch rod, it is bonded to the surrounding ground plane during use. The AM-741 is battery powered to prevent measurement errors that maybe caused by external power cables. The ANSI equivalent capacitance substitution (ECSM) method is the recommended method for calibrating AM-741 monopole antenna. The individual calibration data will be included with each antenna.
-
product
Direct-Reading Dosimeters
The Direct-Reading Dosimeters are rugged, precision instruments. They are designed to measure and directly read, at any time accumulated dose of gamma and x-ray radiation exposure. The Direct-Reading Dosimeter is designed to satisfy military specifications for the IM-Series RADIAC METER and ANSI N13.5 and N322 requirements. The sturdy metal clip attaches the dosimeter to a pocket or any object to monitor total radiation exposure. They are hermetically-sealed and immersion proof.
-
product
Individual UPC Bar Code Standards
The UPC Verification Calibration standards are a unique set of symbols that assures an exact and reliable primary bar code standard exists for UPC codes based on ANSI X3.182/ISO 15416 methodology. These standards assures that manufactures of verification equipment, scanners, QC labs and end users now have an accurate basis for checking the measurement capabilities of their equipment. These standards are intended as a fundamental calibration tool for an QC program, providing a continuous scale from best to worse case characteristics of each parameter. With complete NIST traceable data supplied, it is ideally suited to those requiring traceability, such as ISO certification. Each symbol is individually calibrated to ANSI X3.182/ISO 15416 standards using a custom built microdensitometer. These cards are supplied calibrated for use with a 6 mil scan aperture and 660nm wavelength. (calibration wit other aperture sizes or wavelengths is available)
-
product
Electricity Metering Device Residential
NC30
EDMI presents its single phase multi-tariff ANSI meter, the NC30. The ANSI compliant meter is designed to supply a comprehensive portfolio of revenue-grade features. NC30 has the ability to render an optional disconnect function and has the competency to offer multiple communications option. It has also the capability of storing meter data up to 12 months of its history.
-
product
3" Casters, Set Of 4
HW-63
3" diameter casters for all vertical cabinets offer mobility where needed. Meets or exceeds ANSI and GSA specifications. Shipped uninstalled unless specified.
-
product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
product
LabVIEW Tools for Digital Filter Design and Implementation
LabVIEW Digital Filter Design Toolkit
The LabVIEW Digital Filter Design Toolkit extends LabVIEW with functions and interactive tools for the design, analysis, and implementation of digital filters. New digital filter users can explore classical designs with the built-in interactive design tools, while experienced users can find a breadth of algorithms, filter topologies, and analysis tools for both fixed- and floating-point digital filters. For fixed-point filters, you can model quantization effects, optimize numeric representation/topology, and deploy the design on a digital signal processor or FPGA using automatically generated ANSI C or LabVIEW FPGA code.
-
product
ARINC 429 PMC Interface Module
PMC-429
Avionics Interface Technologies
4, 8, 16, or 32 Software Programmable Tx/Rx ChannelsProgrammable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application Interface supporting C++, C#, and .net DevelopmentDevice Driver Support: Windows, Linux, VxWorks, and other operating system - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
Spectroscopic Personal Radiation Detector
identiFINDER® R200
identiFINDER® R200 instruments are rugged, pager-sized Spectroscopic Personal Radiation Detectors (SPRD). They provide full ANSI N42.32 Personal Radiation Detector (PRD) compliance and feature next-generation solid state detector read-out technology that delivers ANSI N42.48 SPRD compliance with nuclide identification. The R200-G detects and identifies gamma radiation and the R200-GN additionally provides neutron detection capability. Law enforcement agencies and first responders use the R200 during routine traffic stops or high visibility events and in mass transit or critical infrastructure entry control points. The OneTouch Reachback™ feature uses the latest advancements in Bluetooth® and web server technologies to provide large-scale situational awareness by alerting others before arriving on-scene.
-
product
GPIB ANSI X3.28 Interface
Model 4894B-7
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
product
Portable Bar Code Verifier
Inspector 5000 Auto Optic
The Inspector 5000 Auto Optic provides ISO 15416 and ANSI X3.182 Method. This unique portable bar code verifier can interface with either the patented RJS Auto-Optic scan head or a laser scanner. Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple seven-button user interface with a large color LCD display. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
product
Multifunction I/O Device
The Multifunction I/O Device features I/O with varying channels, sample rates, output rates, and other features to meet many common measurement requirements. You can use the device for industry applications such as laboratory automation, research, and design verification. The included DAQExpress companion software provides basic measurement and analysis, while the included NI-DAQmx driver provides the ability to create customized automated measurement and control applications. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
PMC-WMUX for F-16 16PP194 Interface
PMC-WMUX
Alta Data Technologies’ PMC-WMUX interface module (PCI Mezzanine Card for Carriers and Single Board Computers) is a single or dual-channel (A-B Redundant = 4 Busses per Channel) WMUX card supported by the latest software technologies. This product is based on the industry’s most advanced 32-bit WMUX FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer, highly portable ANSI C architecture. This hardware and software package provides increased system performance and reduces integration time.
-
product
C Series Universal Analog Input Module
The C Series Universal Analog Input Module helps you perform multi-purpose measurements. This module includes built-in support for accelerometer, powered sensor, full-bridge, and voltage measurements as well as quarter-bridge, half-bridge, 60 V, and current measurements using measurement-specific adapters. You also can choose options to measure signals from sensors such as strain gages, resistance temperature detectors (RTDs), thermocouples, load cells, and other powered sensors.The C Series Universal Analog Input Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Physical Testing
Testing is confidential and can be conducted according to the client's specifications, or such Standards as MIL-202, 331, 750, 810 and 883, as well as GSA, ASTM, ISTA, BIFMA, ANSI, industry and government.





























