Voltage References
-
product
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle
865683-01
NI-9205, cDAQ-9171, and cRIO-9940 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9205, cDAQ-9171, and cRIO-9940 includes the NI-9205 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the cRIO-9940 Backshell for strain relief and operator protection from high-voltage signals. The included NI-9205 features a channel-to-earth ground double isolation barrier for safety, noise immunity, and high common-mode voltage range. Additionally, the NI-9205 provides up to 60 V of overvoltage protection between input channels and common, and it is rated for 1,000 Vrms transient overvoltage protection.
-
product
PXI/PXIe High Voltage Multiplexer, Hex 7-Channel, 1-Pole
42-321-103-HI
The 40-321-103-HI (PXI) and 42-321-103-HI (PXIe) are hex 7-channel 1-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Dual Voltage Buffer with Current Drive
BUF-01
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
product
Pulse Rate to 4-20mA or Voltage Converter
SY020
The SY020 Pulse Rate Converter can be linked to any frequency generating device e.g. flow meters, which gives TTL, pulse Reed switch or coil output, converting the frequency to an analogue signal. This can be 4-20mA loop current or a voltage output. The 4-20mA version unit is loop powered.
-
product
Voltage Probes
In addition to EMI measurement with LISNs (Line Impedance Stabilisation Networks, Artificial Mains Networks), Probes are used for Terminal or Line voltage measurement.
-
product
Voltage Controlled GUNN Oscillators
GV-8 / GV-6
Voltage controlled GUNN oscillators provide optimal electronic tuning by coupling GUNN with tuning varactor. Oscillators provide low AM and FM noise, making them suitable as local oscillators or transmitters.
-
product
Three Phase High Precision Reference Standard Energy Meter
SY3102
Hong Kong Songyang Industrial Ltd.
There are three ports for pulses to output. And its constants can be set automatically or manually. Types of constants can be set also: active power, reactive power, apparent power, voltage, and current.
-
product
HIPOTS (High Voltage Testers) / AC Hand Gloove and Boot Safety Tester
UDEYRAJ ELECTRICALS PRIVATE LIMITED
Compact and rugged BDV testers for AC dielectric withstand / breakdown testing of Safety glooves and boots. Panel mounted controls and indicators with easy to follow legend.
-
product
Oil Break Down Voltage Test Set
This set is widely used in industries to test the load bearing capacity of insulating oil or liquid.
-
product
High Voltage Products
Advanced Energy's high voltage products feature high-performance power supplies and amplifiers. Each product line features hundreds of units, options, and accessories to meet your application needs.
-
product
Low Noise Voltage Preamplifier
1201
The Model 1201 Voltage Preamplifier with Remote Gain Programming Option (06) is usable in both computer controlled and maual applications requiring uncompromising performance.
-
product
Provides 3 Wire Voltage Output
SEM1620
The SEM1620 signal conditioner provides a 3 wire isolated voltage output signal and accepts RTD, Thermocouple, mV and passive current sensor inputs
-
product
Relay Testing Voltage Source
PTE-FCN
It is the easiest and most economical way of increasing the relay types that can be tested with the PTE-100-C. The PTE-FCN includes its own LCD display and a BUS-PTE connection, which makes it easier to operate and enables it for use in combination with any other test set in the PTE range. The PTE-FCN is included as standard in models PTE-100-C Pro and PTE-50-CE Pro.
-
product
High Voltage Power Source
PM2000
The PM2000 is a high voltage power source capable of supplying up to 2000 V and sourcing 10mA to a load. The high potential at 2 kV fulfills coverage for mostly all semiconductor devices where leakage and breakdown measurements are involved. The module has been incorporated with interlock feature to ensure safety.
-
product
High Voltage 50 Pin D-Type Connectors
The connectors below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.
-
product
UHVDC(Untro High Voltage DC) Testing
In the super (ultra) high-voltage transmission field, UHVDC converter stations are mainly composed of three parts: AC system, valve system, and DC system. Each part consists of primary and secondary electrical equipment. PONOVO, relying on its core technology, extensive system testing experience and high-efficiency production capabilities, have continuously explored super (ultra) high-voltage test technologies, and nearly 10 types of test equipment have been developed for converter system substations and system debugging.
-
product
AC / DC Combined High Voltage Test Set
Cambridge Instruments & Engineering Co.
suitable to perform AC High Voltage Power Frequency test on transformers, motors, cables etc. Leakage current can be measured at desired pressure and this set can be used as a source for cable fault burning.
-
product
Voltage And Continuity Testers
Unlike voltage testers, continuity testers are always used when a circuit is turned off—or on wiring or devices that are disconnected from the circuit. They don't test for the presence of voltage but rather to see whether an electrical path is intact in an appliance or a device.
-
product
High Voltage Capacitor Batteries
Lifasa - International Capacitors, SA
There are a series of elements and materials, just like in the BT equipment, for their operation in AT and that must accompany our AT capacitors for the proper functioning of these and for our installation / network, as well as the rest of equipment that compose it and that are in operation in parallel to the capacitor / s that we want to put into service for the correction of the power factor (compensation of the consumption of reactive energy).
-
product
Reference Supplies
Advanced Energy's Trek reference supplies offer both high temperature and time stability outputs. They can also be used as a secondary traceable standard.
-
product
High Voltage (Hipot) Cable Tester
CH2
The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.
-
product
Charger and Low Voltage Power Supply
FlexiCharge FC1500
The FC1500 Medical Capacitor Charging power supply, with a built in configurable ACDC power supply is designed to provide the system power needs for Medical laser applications. The FC1500 can provide both capacitor charging and ACDC low voltage system power due to it’s unique design and intelligent control. The FC1500 can be used as a standalone capacitor charger, and if needed, various low voltage modules can be added to the unit to provide further system power. This functionality provides extra flexibility to power other systems and applications. Low voltage modules can be connected in parallel and in series for application that require higher voltage and current requirements. The Capacitor charger capabilities has the highest level of performance due the unique built in intelligent control for capacitor charging, higher charge rates and power limit control.
-
product
Stand Alone Low Voltage Tester
TestMate 256
The TestMate continuity tester features a universal interface fixture that accommodates adapter cards for quick changes in harness setups. Adapters can be exchanged in seconds to adapt quickly to any of a variety of wire-harness/cable connectors.
-
product
GPS Frequency Reference
E8000
The Quartzlock E8000 GPS Frequency Reference is a breakthrough in exceptionally low cost, traceable, 1-U rack mount, calibration-free, off-air frequency & time standards. These very low cost references maintain the high frequency & time accuracy required for demanding applications. Ultra low noise option are available.
-
product
High Voltage Surge Current Monitors
HVSCM
Designed to be used with the Model HVST High Voltage Surge tester. The Surge Current Monitor allows simultaneously surge testing 20 units. The Surge Current Monitor monitors the current going through each unit under test at the time of the surge. If a unit under test breaks down or leaks, the Surge Current Monitor will identify the bad unit by lighting the corresponding LED. The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. In production testing we expect that most of the time the devices will pass. In the event that one should fail, the failed device would be removed and then all the parts would have ot undergo another surge test. Since most devices pass most of the time, simultaneous surge testing can be a real time saver.
-
product
Attitude Heading Reference System
(AHRS) TRAX2
Using its unrivaled magnetic sensor expertise , PNI fuses its proprietary magnetic sensors and sensor fusion algorithms, delivering accurate AHRS heading without the need for GPS.
-
product
PXI/PXIe High Voltage Multiplexer, Quad 5-Channel, 2-Pole
40-321-121-HI
The 40-321-121-HI (PXI) and 42-321-121-HI (PXIe) are quad 5-channel 2-pole high voltage multiplexers capable of hot or cold switching up to 1000 V peak. They are also available in a range of bank sizes with 1 or 2 poles and channel counts between 4 and 48. High quality reed relays are used throughout.
-
product
Acute High Voltage Differential Probe, 50x/500x, 100MHz, 3500V
ADP5100
*USB Powered (or Power Bank)*Bandwidth up to 100 MHz*Overrange Indicator*Audible Overrange Alarm*Bandwidth Limit : 5 MHz / Full*Can be used by any DSO which has the USB port(s).*EC Declaration: EN 61010-031:2002 +A1:2008*Double-layer wire for power insulation
-
product
CMOS Drive High Voltage SIL Reed Relays for up to 3 kilovolts
Series 101
Direct drive from 74HC/HCT Cmos SIL Relay. Dry or Mercury Wetted switches. 5 Volt coil for 1A dry version is 1600 0r 3000 Ohms
-
product
PXI Voltage Amplifier D Type Connector
41-650-001
A 5 channel voltage amplifier ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test.





























