Remote Terminal Unit
Collects data from data acquisition (DAQ) devices and transmits the information to the main test system via a network.
-
product
Electronic Control Units
Self-contained engine management system and data logger for race engines up to eight cylinders. The unit is complete with integrated ignition and injection drivers and so needs no external units to run an engine.
-
product
PXI/PXIe Microwave Multiplexer, Triple SP4T, 26.5GHz, 50Ω, SMA, Terminated, Remote Mount
40-785C-433-TE
The 40-785C-433-TE (PXI) and 42-785C-433-TE (PXIe) are triple SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
PXI/PXIe 1000Base-T1 Fault Insertion Switch, 6-Channel
42-203-002
The 40-203-002 (PXI) and 42-203-002 (PXIe) are designed to simulate common faults on high-speed two wire communication interfaces such as 1000Base-T1. They support 6 channels of two wire serial interfaces. Each channel pair can simulate an open fault in either or both wires, and using the fault bus switches can simulate short between both wires or a short to one of two externally applied fault connections – such as battery supply or ground - via two fault buses.
-
product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA, Terminated, Remote Mount
40-785C-432-TE
The 40-785C-432-TE (PXI) and 42-785C-432-TE (PXIe) are dual SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
product
Digital Termination Boards
MSTB 008
For quick and secure connection of discrete wires to a Data Acquisition Processor (DAP) board, use the MSTB 008 Digital Termination Board.
-
-
product
Terminations (Loads)
Loads find wide use as accessories for both broadband and narrowband measurement instruments. Keysight's family of fixed and sliding loads includes both general purpose grade loads as well as loads intended for use as calibration standards.
-
product
Tilt Switch and Control Unit
MTS / SCU-200
Features • Detects the presence or absence of bulk material • Standard enclosure is NEMA 12 with indicator lights • NEMA 4 and Intrinsically Safe enclosures available • Rugged heliarc-welded steel probes • Use with SCU-200 for complete monitoring system
-
product
Data Broadcast Units
The DBU-TTL Data Broadcast Unit is designed for use in receive only data broadcast applications. The unit supports 8-Ports Data/Clock distribution of TTL signals on BNC connectors. 1U rack mount chassis.
-
product
Lighting Management Units
Highly integrated, flexible lighting management ICs support nearly all the illumination tasks performed in mobile phones.
-
product
CB-37FH, DIN-Rail Horizontal Mount 37-Pin Spring TB
778676-01
37-Pin Female D-SUB to 37-Pin Female Connector, Horizontal DIN-Rail Terminal Block - The CB-37FH is an unshielded terminal block that provides access to NI data acquisition devices with 37-pin female D-SUB connectors. The CB-37FH mounts in line with the DIN rail, and it featuresscrew or spring terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
product
Programmable Logic Units
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
product
Commutator Testing Unit
SCR ELEKTRONIKS have designed “Commutator Testing Setup” to provide Commutator manufacturers and users a simple and speedy method for testing their Commutators. This single station commutator testing set up therefore user can test one commutator at a time. In Automatic mode of testing this set up performs two tests automatically.
-
product
Voltage Regulator Testing Units
With the goal of providing the industry with the best products ahead of the curve, we continue to develop a complimentary line of Voltage Regulator Testing Units for laboratory and production testing.
-
product
Load Support Unit
LSU220A
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
product
TB-2648, Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block
781131-01
Screw Terminal, 4x128, 1-Wire PXI Module Matrix Terminal Block - The TB-2648 provides the necessary routing to configure the PXI-2531 or PXIe-2531 PXI Matrix Switch Module as a 1-wire 4x128 matrix. You can directly connect the TB-2648 to the front panel I/O connectors of the PXI-2531 or PXIe-2531.
-
product
Railway Motion Control Unit
RMCU
The Railway Motion Control Unit – RMCU is a high-performance strapdown system developed for Railway applications to determine the absolute orientation (Heading, Pitch, and Roll) and motion parameters (Angular Rates and Linear Accelerations) for any Railway Platforms on which it is mounted. Orientation is determined with high accuracy for both motionless and dynamic applications.
-
product
Remote Corrosion Monitoring
Telemetry System
Metal Samples’ remote telemetry system obtains real-time corrosion monitoring data via the Internet from anywhere in the world. The system features communications via satellite to a secure Web Monitor data server. With this powerful web-based back end, you can bring the data to your desk no matter where the site is located.
-
product
CB-37FH, DIN-Rail Vertical Mount 37-Pin Spring TB
778685-01
37-Pin Female D-SUB to 37-Pin Female Screw Terminal, Vertical DIN Rail Terminal Block - The CB-37FH is an unshielded connector block that provides access to NI data acquisition devices with 37-pin D-SUB connectors. The CB-37FH is a vertical connector block that mounts perpendicular … to the DIN rail. It features screw terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
product
Terminations And Mismatch Loads
JFW’s online 50 Ohm Low power termination and mismatch load models are listed in the table below. JFW has been designing, manufacturing, and delivering quality terminations and mismatch loads for over 30 years. Our mismatch loads allow you to select the impedance mismatch your RF testing requires.
-
-
product
Terminations
Coverage from DC to 40 GHzPower handling up to 500WExcellent return lossVariety of connector types
-
product
Remote Plasma Source
MAXstream
Advanced Energy’s MAXstreamTM line is the next generation of remote plasma sources for chamber cleaning. The MAXstream is available in 3, 6, 8, 10, and 12 SLPM NF3 flow rates to optimize price and performance.
-
product
Ignition Driver Units
A compact inductive ignition drive unit which drives two banks of five ignition coils. The drivers are controlled via direct logic signals from a host ECU and provide fire-by-fire diagnostics back to that unit via CAN. The coils can be run at voltages up to 30V with this unit in order to minimize dwell times for optimum response.
-
product
Remote Spectrum Analyzers
LPT-3000RX4
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
-
product
Fuel Display Unit Tester
MS 1125
Fuel Display Unit Test Bench is a compact table-top test bench with front panel controls, indications, built-in signal simulator and necessary power supply for testing the serviceability of Fuel Display Unit of Helicopter. FTB operates on 230 V AC and supplies 28 V DC power to FDU. FTB is housed in a metallic cabinet FTB interfaces with both 61 Pin connector and 6-pin socket mounted on the rear panel of FDU by means of the cable connected to the unit. FTB is fabricated utilizing off-the-shelf standard industrial/commercial components like rotary switches, toggle switches, press switches, test sockets, fuse holders, potentiometer etc. The Frequency generation circuit is integrated into FTB for the simulation of Fuel probe and flow rate signals. The frequency of the signal can be selected by means of a rotary switch Low amplitude sine wave signal is simulated for testing flow rates. Variable voltage DC power supply with a voltage range of 24 to 29 Volts is provided within FTB to power-up FDU. 5 V DC is provided for the operation of signal generating circuit (PIC Frequency Controller Board). An off-the-shelf Hand held battery operated Digital Multimeter (DMM) procured from the prominent manufacturer (FLUKE) is supplied with FTB for setting up and measurement of various parameters like Resistance, Voltage, Frequency etc.
-
product
Microwave Remote Sensing Instruments
Scintillometers
We offer a wide range of Microwave Remote Sensing instruments. From Radiometers such as Humidity and Temperature Profilers, Cloud Radars up to Scintillometers.
-
product
Remote Display Analyzer
The power of Remote Display Analyzer lies in the simplicity. Because RDA will only show what you need when you need it there’s no distraction or complexity.Specific display modes require specific settings, when Remote Display Analyzer detects a display mode it will alter itself accordingly.
-
product
Load Termination
A process of ending a transmission line or cable to either dissipate energy as heat or prepare it for connection to a device.
-
product
PXI Chassis And Remote Controllers
We offer both PXI & PXIe chassis and controllers that support all of our PXI switching and simulation modules as well as those from third parties. There is a choice of up to 21-slot 3U chassis with options to reduce acoustic noise and modules that can be powered from a DC source.
