PCMCIA Adapters
Adapters that fit in the PCMCIA slot in notebook computers. Different adapters have different functions but they all add connectivity possibilities. (beststuff.co.uk)
-
product
RS232 I2C Adapter
12C Master
*I2C frequency adjustable up to 400kHz*I2C level shifter, I2C level from 2V to 15V*Interrupt input for external events*Simple software interface (ASCII commands)
-
product
DDR4 Pro Memory Test Adapter
This memory test adapter for the RAMCHECK LX includes an extraordinarily rugged test socket for many thousands of insertion/removal cycles.
-
product
XMC-to-PCI Express (PCIe) Adapter
8615
The Technobox, Inc. P/N 8615 XMC-to-PCI Express adapter with Rear I/O support permits use of a standard VITA 42.3 air-cooled XMC, or VITA 20 conduction-cooled XMC, in the smallest possible edge finger PCI Express form factor. The length of the adapter is the length of the XMC, and 10 mm mezzanine stacking height is supported. The height is a standard PCI Express board, and is not the low-profile version.
-
product
2.92mm to ProLink Adapter with Probe Power and Communication Pass Through
L2.92A-PLINK
The Teledyne LeCroy LabMaster 10 Zi oscilloscope utilizes precision 2.92mm input connectors to achieve up to 36GHz of input bandwidth. But some applications may require the use of lower-bandwidth probes for performance and cost reasons.The L2.92A-PLINK adapter converts the 2.92mm interface to a ProLink interface. This brings the benefits of a wider selection of probes to the LabMaster 10 Zi such as Dx10/Dx20/Dx00A-AT 4-6 GHz differential probes and DH Series 8 to 20 GHz differential probes using the ProLink oscilloscope probe connection. Full probe power and control is provided through a built-in LEMO interface.
-
product
Osprey PCI Unibus Adapter
9793
Dual-height card plugs into PDP-11 Unibus backplane. Fibrechannel cable plugs into Unibus logic connector on Osprey /TXP I/O Adapter logic provides Programmed I/O and DMA access to "real" Unibus compatible controllers (those not otherwise emulated).
-
product
Local DVB-T2 Adapter
T2 Edge DTH
T2Edge DTH is ENENSYS local DVB-T2 adapter of the OneBeam DVB-T2 solution. Running on the transmission site prior to the DVB-T2 transmitter, the T2Edge DTH aims at receiving a DTH stream to build a new DVB-T2 multiplex. It selects the services from the DTH stream and generates a T2-MI stream. The T2EdgeDTH performs an advanced PSI/SI processing to update PSI/SI information related to the filtered services.
-
product
XMCDisk, SATA Adapter
9292
The 9292 XMCDisk is a rugged mezzanine storage solution designed for applications requiring high speed operation with high capacities and zero slot usage.
-
product
EBIRST 50-pin D-type To 37-pin D-type Adapter
93-005-418
eBIRST adapters allow extension to other switching system connectors, including SMB
-
product
GPIB (female)
182766-01
24-Pin, Female GPIB (IEEE 488) to 24-Pin, Female GPIB (IEEE 488) Bulkhead - The GPIB Bulkhead connects GPIB cables to other accessories. NI offers it in Type XC and XD.
-
product
Adapter, 1.0 mm (m) to 2.4 mm (f), DC to 50 GHz
11922C
The Keysight 11922C precision 2.4 millimeter coax in adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and a frequency range from dc to 50 GHz.
-
product
Protective Cover, G20x, ITA, 6.75" Series Adapters
410112986
Protective Cover, G20x, ITA, 6.75" Series Adapters
-
product
Adapter, 1.0 mm (f) to 1.85 mm (f), DC to 67 GHz
11921F
The Keysight 11921F precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
product
Piranha USB-FXS Adapter
SKU-083-01
The Piranha USB-FXS Adapter is the second product in the Piranha USB Adapter™ family. This device simplifies and makes a cost-effective analog phone connection for a telecommunication system. Our design is ultra-compact – this USB-FXS adapter is designed to be a part of the actual cable between your analog phone and your system’s USB port.
-
product
True RMS Clamp Meter w/ Pipe Clmap Adapter
DL489COMBO
UEi Test & Measurement Instruments
True RMS Clamp meter and 2 ATTPC3 pipe clamp adapter, 2 ATT29 K-Type temperature probes
-
product
Test adapter HR-LR
MA-HL02
Hachmann Innovative Elektronik
Our test adapter MA-HL02 connects LR measuring devices to standardized HR string parts. Due to small dimensions and skid-proof design it's easy for him to catch up with everything.
-
product
Adapter / Carrier Converter Card
PCIBPC104pET
PCIBPC104pET adapter / carrier converter card provides the ability to install 1-4 active PC104p or PCI-104 cards into a standard PCI slot. PCIBPC104pET has a PC104p and PCI-104 compatible stack position mounted to a universal voltage shorter than 1/2 length PCI card. The PC104p position is stackable with all 4 active positions usable.
-
product
Test Adapters
In our specially developed MG range of linear test adapters (test fixtures), we use solid aluminium components in our mechanical construction. This is to ensure the reliability and contact accuracy of the test adapter.
-
product
Run Down Adapters
Screw RDA
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
product
PCI-to-CardBus/PCMCIA/PC-Card Adapter, 2 Slots, Texas Instruments PCI1520 Chipset
P222-TI1520
The PCI to 2-slot PCMCIA/CardBus PC-Card adapter supports 3.3V & 5V PC-cards (PCMCIA/Cardbus) simultaneously. Hot-swap PCMCIA/Cardbus PC-cards without powering off the system. 2 independent icons in MY COMPUTER. The adapter is quick & easy to install, allowing PC-card devices to be used in any desktop or tower PC.
-
product
RF Adapters
BNC Adapters
Amphenol RF offers a wide array of both in-series and between-series BNC adapters in straight and right-angle configurations. 50-ohm and 75-ohm impedance BNC adapters are available with and without panel mounting features. Popular mounting features in bulkhead, both front and rear mount, and 4-hole flange designs. 50-ohm BNC connectors have a frequency range from DC to 4 GHz. 75-ohm BNC connectors optimized for 4K/UHD video applications can perform well to 12 GHz.
-
product
Adapter to Convert (mini-PCI) mPCI
PMC2mPCI
Install wireless and other mPCI devices into PMC environments. PMC2mPCI adapts the PMC form factor to mini-PCI type III. PMC2mPCI installs into a standard PMC position - 32 bit PCI bus connectors, standard power and ground, standard standoffs and blank bezel.
-
product
3U CPCI To PCI 4 Slot Adapter
The PCI-Adapter is a carrier board, allowing the operation of any standard (desktop) PCI card in a CompactPCI® system. The PCI-Adapter acts as a PCI bridge, providing an electrically and mechanically optimized interface between PCI and CompactPCI® system. Our adapters include a PCI Bridge. Some competitor products do not provide a PCI bridge, thus reducing adapter costs by tolerating a violation of the PCI specs. Overall PCI compatibility however is a must in order to achieve total system reliability. Please bear these facts in mind, when comparing prices of PCI-Adapters. All modern operating systems can treat a PCI bridge in a plug and play manner meaning that the bridge remains virtually transparent, as if the PCI component(s) behind the bridge on the secondary PCI bus were part of the primary PCI bus. Using the PCI-Adapter/bridge allows standard PCI boards to work in a CompactPCI® system is both a reliable technical solution, and a smart economical decision. The PCI-Adapter frees the system integrator from the need of a redesign of PCI cards already available to the CompactPCI® standard. This is a great advantage, especially when time to market is critical, or the number of systems to be built is limited, or the function to be implemented has fast innovation cycles.
-
product
Adapter, 1.0 mm (m) to 1.85 mm (m), DC to 67 GHz
11921E
The Keysight 11921E precision 1.85 millimeter coax-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 67 GHz.
-
-
product
COM Express Type 7 10GbE Optical Fiber Network Adapter Card
10GbE Optical Fiber Network Adapter Card
- Supports up to four 10GbE optical fiber interfaces (SFP+)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
product
Protective Cover, G20, 6.75" Series Adapters, Receiver
310113422
Protective Cover, G20, 6.75" Series Adapters, Receiver
-
product
DH Series QuickLink Adapter Kit with 3 x QL-SI Tips
DH-QL-3SI
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
-
product
RF Adapters
UHF Adapters
Are general purpose units developed for use in low frequency systems from 0.6 - 300 MHz.
-
product
Protective Cover, G20x, Receiver, 6.75" Series Adapters
310113597
Protective Cover, G20x, Receiver, 6.75" Series Adapters
