Interrupters
-
product
Power System Multimeter
928A
The Model 928A Power System Multimeter with Floating-Point DSP™ Digital Signal Analysis is an AC Power measurement instrument, providing outstanding performance and flexibility in a small, hand-held package. Not only does the Model 928A measure basic data and power quantities, but it also measures power quality including harmonics, flicker, sags, surges and interruptions. Incorporating a graphic LCD display, serial communications, real time clock and an unprecedented combination of features makes the Model 928A the ideal instrument for the power professional.
-
product
IP Parallel HV
High Voltage [up to 30V] IP Compatible card with 48 programmable IO. 40 mA sink. Open collector interface. Interrupt generator on each input channel. Filtered or direct input.
-
product
PXI-8512, 1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module
780687-01
1‑Port, High-Speed, Flexible Data Rate PXI CAN Interface Module—The PXI‑8512 is a high-speed Controller Area Network (CAN) Flexible Data-rate (FD) interface for developing applications with the NI‑XNET driver. The PXI‑8512 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimize message latency and freeing host processor time for processing complex models and applications.
-
product
High Power Programmable AC Source with Transients
61510
Chroma Systems Solutions, Inc.
Power Rating:61511: 12KVA61512: 18KVAVoltage Range: 0-150V/0-300V / AutoConfigurations with input voltage of 220V or 480VFrequency: DC, 15Hz-1500HzSingle-phase or three-phase output selectableProgrammable slew rate setting for changing voltage and frequencyProgrammable voltage and current limitHigh output current crest factor, ideal for inrush current testingTurn on, turn off phase angle controlTTL signal which indicates output transientLIST, PULSE, STEP mode functions for testing Power Line Disturbance (PLD) simulationVoltage dips, short interruption and voltage variation simulationHarmonics, inter-harmonics waveform synthesizerComprehensive measurement capability, including current harmonicsAnalog programmable interfacesRemote interface: GPIB, RS-232, USB and EthernetCapable of delivering power output up to 90KVA by implementing Master-slave parallel operation
-
product
Interface
P-SER
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
product
Shared Memory Network XMC Interface
XMC-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
Visual Analysis of any Embedded System
SystemView
SEGGER Microcontroller GmbH & Co. KG
SEGGER is announcing the release of SystemView, a free tool enabling the visual analysis of any embedded system. SystemView gives complete insight into the behavior of a program, with minimal side effects on the observed embedded system. SystemView offers cycle accurate tracing of interrupts and task start stop as well as task activation and API calls when an RTOS is used. It visualizes and analyzes CPU load by task and interrupts and scheduler. Test setups with LED and oscilloscope are a thing of the past.
-
product
STD Bus Backplane
VECTOR Electronics and Technology, Inc.
Vectorbord® STD Bus industrial backplanes per IEEE 961 microcomputer bus, compact and rugged are fully assembled and tested. Designed for 4.5” X 6.5” plug-in boards, Vector STD Bus backplanes are available in 8 or 16-slots. Speed capability up to 10MHz; 2-layer design. Ample positions for decoupling capacitors; interrupt priority lines.
-
product
PXI-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
778572-14
7-Channel, 40 A PXI Signal Insertion Switch Module—The PXI‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXI‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls
-
product
Vacuum Interrupter Pressure Integrity Test Set
Low Drift Current is measured by applying magnetic field.
-
product
PXIe-2514, 7-Channel, 40 A PXI Signal Insertion Switch Module
780587-14
PXIe, 7-Channel, 40 A PXI Signal Insertion Switch Module—The PXIe‑2514 fault insertion unit (FIU) is designed for hardware‑in‑the‑loop (HIL) applications and electronic reliability tests. Each module has a set of feedthrough channels that you can open or short to one or more fault buses. You can use this architecture to simulate open or interrupted connections as well as shorts between pins, shorts to battery voltages, and shorts to ground on a per-channel basis. When controlled with the LabVIEW Real-Time Module, the PXIe‑2514 is ideal for validating the integrity of control systems including engine control units (ECUs) and full authority digital engine controls (FADECs).
-
product
Arduino CAN Shield
IFB-10003-INP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCI-1564
32 bit, 33 MHz, PCI interfaceInput channels32 isolated digital input channels, 24 V, incl. 16 interruptible and 3 fast counter inputsInput channels organised in 4 groups of 8 channels, each group has its own ground lineVoltage reversal protectionAll inputs are filteredOutput channels32 isolated digital output channels, 10 to 36 VOutput current per channel 500 mAWatchdog for resetting the outputs to "0"After power/ON the outputs are reset to ì0îShort-circuit current for 16 outputs ~ 3 AShort-circuit current for 32 outputs ~ 6 AShort-circuit current per output ~1.5 AElectronic fuseOvertemperature and overvoltage protection24 V power outputs with protection diodes and filtersSpecial output capacitors minimise electromagnetic emissionsExternal 24 V supply screened through a protection circuitryShutdown logic when the external supply voltage drops unter 5 V
-
product
PC/104 Input/Output Module providing 96 lines of digital I/O
PCM-UIO96C-16
The PCM-UIO96C-16 is a highly versatile PC/104 input/output module providing 96 lines of digital I/O. One important feature of this card is its ability to monitor 48 of the 96 lines for both rising and falling digital edge transitions, latch them, and then interrupt the host processor notifying that a change-of-input status has occurred. This is an efficient way of signaling the CPU of real-time events without the burden of polling the digital I/O.
-
product
Multifunction Power & Harmonics Analyzer
KM 2100 / KM 2200
Kusam Electrical Industries Limited
Volts / Amps. / Hertz, Dips & Swell, Power / Energy. Unbalance, Monitor, Scope, Harmonic, Logger &, Interruption functions. (KM 2200). Inter Harmonics, Transient Voltage, Inrush Current, Flicker function not available in KM 2200. Frequency upto 400Hz (KM 2100); 50 / 60Hz (KM 2200). Single-phase 2W / Single-phase 3W / 3-phase 3W / 3-phase 4W. Flash memory 128MB. TF Card 8G Memory Card for long-term measuring data storage. Support USB port to connect to PC and analyze the data / screen shots copied by U-disk. Support LAN port to make the remote control available, transfer the measuring data.
-
product
Circuit Breaker Finder
6504
Peaceful Thriving Enterprise Co Ltd
Circuit Breaker Finder is a multi-function circuit tracer/ identifier. Circuit Breaker Finder identifies circuit breakers without interrupting service.This device is formed by 1x Transmitter and 1x Receiver. There are 3 functions: (1) Socket Tester (Wire Mapping)(2) Circuit Tracing / Identifying(3) Non-Contact Voltage Detecting
-
product
72.5-Watt DC Power Line Conditioner w/Holdup
44KS3-02
NAI's 44KS3-02 is a 72.5-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides a single output at 72.5 Watts either 22.5 to 30 VDC with holdup time or +16 VDC without holdup time - to all downstream DC/DC converters.
-
product
Current Transformer with Open Core
TCP
Lifasa - International Capacitors, SA
The TCP series is designed for installations in operation. It has a removable core that allows its connection without interrupting the power supply.
-
product
Shield Level / Pathloss Equipment
PAMS & PAMS-C
PAMS is a user-friendly, transmitter and receiver system that measures shielding effectiveness in RF shielded enclosures. Lightweight and compact, each PAMS unit measures approximately 12” x 5” x 5” and weighs 5.5 lbs., making PAMS ideally suited to field measurement tasks. Rugged construction insures instrument survivability in a field test environment. PAMS-C is a simple and efficient solution for quickly identifying shielding faults in an RF shielded enclosure. Cousin to the original PAMS used extensively by customers operating RF Shielded Enclosures, PAMS-C gives commercial end-users everything needed to measure shielding effectiveness levels of critical infrastructure - all with minimal or no interruption to normal operations.
-
product
USB-8506, 1-Port, USB LIN Interface Device
784663-01
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
product
Powered VME Crates
VME is a high speed and high performance bus system with powerful interrupt management and multiprocessor capability. It was created by combining VERSAbus electrical specifications (1979) with the Eurocard format resulting in the VMEbus Revision A - 1981 specification. The VMEbus specification has since then been refined through revisons B (1982), C, C.1, IEC 821 & IEC297 and IEEE 1014-1987.
-
product
100-Watt DC Power Line Conditioner w/Holdup
44LS1
NAI’s 44LS1 is a 100-Watt Power Line Conditioner with holdup time that protects downstream DC/DC converters from transients, low voltage conditions, and power interruptions. This unit accepts +28 VDC input and provides 22.5 to 30 VDC at 100 Watts to all downstream DC/DC converters.
-
product
Optical Fiber Identifier
Anfkom International Co.,Limited
It is an essential installation and maintenance instrument.By inserting the fiber into its adapter head,it can identify SM optical fibers without any damage by detecting the optical signals being transmitted through them so as to avoid the opening of the fiber at the splice point for identification and thus avoids the interruption of the service.In the presence of traffic, the intermittently audible tone is activated.The 3306A optical fiber identifier also allows relative core power display and identification of the 270Hz,1kHz and 2kHz frequencies. When they are used to detect the frequency, the continuously audible tone is activated.There are four types of adapter heads available: 0.25,0.9,3.0 and 2.0.The 3306A optical fiber identifier is powered by a 9V alkaline battery.
-
product
C012 Communication Board
MS 1728/29
- Suitable for standard desktops- Four channel in single board- Up to 10 Mbits/sec operating speed- Low Cost solution- Standard INMOS link protocol- Communicates with transputers- Converts between serial link and parallel bus- Tristate bidirectional bus interface- Memory mapped registers- Interrupt capability- TTL compatibility
-
product
Opto-Isolated Current Loop Signal
4029
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
product
Shared Memory Network PXI Express Instrument
PXIe-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - 3U PXI Express Module - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
Extension Kits
Ready to use extension packages for special methods e.q. high current interrupt or AC-DC-AC test on laminates.
-
product
Clamp Meters
Kyoritsu Electrical Instruments Works, Ltd.
The clamp on the device is simply placed around a live wire. This allows one to measure the current on a wire without interrupting the operation of the electrical appliance. A clamp meter uses digital technology to bring instantaneous readings.
-
product
Switch Module
STCS
The external module STCS allows performing automatically the following PT tests: ratio per tap; winding resistance; OLTC dynamic test. The connection to the transformer under test, to STS and to the measurement taps is performed just once; then, all transformer tests are performed without interruptions.
-
product
Multichannel Memory-Mapped ARINC 708/453 Interface Card
EXC-708mPCIe
The EXC-708mPCIe is a multichannel, memory-mapped ARINC 708/453 interface card that supports two ARINC 708/453 channels, each programmable as transmit or receive. Each channel implements a 64K x 16 FIFO and supports polling and/or interrupt driven operation. The card complies with the PCI ExpressTM Mini Card standard. It’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 708 interfaces and for performing system simulation of the ARINC 708/453 Weather Radar Display databuses, both in the lab and in the field. In Transmit mode, each ARINC 708 word is written to the FIFO as a block of 100 16-bit words. In Receive mode, each ARINC 708 word is stored in the FIFO as a block of 103 16-bit words. The first two words comprise the 32-bit Time Tag, indicating the word’s time stamp. The next 100 words comprise the 1600 bits of the ARINC 708 word, which are followed by the Status Word.The EXC-708mPCIe card comes complete with C drivers including source code.
