Telephone Line Testers
See Also: Telephone Line Test, Butt Set
-
product
Insulation Resistance Tester
UDH-50-1-T
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated• Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV • Resistance range to 1TΩ • Continuous digital display on LCM• Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
product
Loop A Line Products
Cable pair tracing and a lot more, Loop-a-Line products can remotely control a far end device (the oscillator) for up to 20km of cable. Using a Loop-a-Line allows the linesman to remotely change the state of the oscillator to any of five different states. Therefore eliminating the need for multiple journeys along the cable path.
-
product
Large Range Resistivity Tester
HS-SFRT
HS-SFRT silicon filament resistivity tester is an advanced silicon cylinder resistivity tester, which can measure silicon filament, silicon phosphorus ingot, silicon boron ingot, seed crystal and so on. As it eliminates Peltier effect, Seebeck effect, minority carrier inject effect and so on, So it improve the accuracy greatly. The testing resistivity ranges from 0.0005Ω·cm to 50000Ω·cm. It is accurate, stable and convenient and a good friend to Siemens polysilicon material producer, SH4 polysilicon material producer, UMG polysilicon material producer and so on.
-
product
Concrete Tester & Surveyor
CTS-02V4
CTS-02V4 (Concrete Test and Surveyor) is a Non-destructive testing device for estimation of compressive strength of concrete. CTS estimates the compressive strength of concrete based on Mechanical Impedance Method by measuring a waveform of impact force with an accelerometer which mounted on the hammer unit.
-
product
Transformer Insulating Oil Dielectric Tester
CXYJ-501
Shenzhen Chuangxin Instruments Co., Ltd.
Insulating Oil Tester is designed according to of GB-86 and IEC60156 standards.
-
product
RS-232 Line Driver with Control Signals and LCD Display
Model 224
FEATURES: DataSpy® Status Display; Full Duplex & Handshake; Loopback & DTE/DCE Switch; DC to 19.2 KBPS; Supports DTR & DCD; Optically Isolated. The Model 224 RS-232 Line Driver with Control Signals and LCD Display provides for transmission of a handshake signal in each direction, in addition to communicating full duplex data up to 19.2 KBPS and providing complete optical isolation.
-
product
E-Z Check® Circuit Tester
61-035
*Tests for correct wiring, open ground, reverse polarity, open hot, open neutral, hot on neutral, hot and ground reversed with open hot in 3 wire, 120 VAC circuits*Simulates ground fault for testing GFCIs*No-slip ergonomic design maximizes comfort*Premium neon lamps prevent false readings*Tough, impact-resistant case*2-year warranty
-
product
Megohmmeter Insulation Tester
AMIC-30
The AMIC-30 insulation tester is a small portable meter designed to measure insulation resistance in electrical and telecommunications installations, cables, motors, transformers and other equipment. The test voltage can be programmed in steps from 10 V to 1000 V. The instrument can measure both insulation resistance over a wide range (0,1kΩ...100GΩ), and insulation leakage current, capacitance and other parameters. All test results can be stored in the internal memory and sent to a computer via the included wireless USB receiver. The meters are supplied with rechargeable Ni-Cd batteries.
-
product
Geotextile Water Permeability Tester
TG010
TESTEX Testing Equipment Systems Ltd.
Geotextile Water Permeability Tester, to determine the constant-head water flow capacity (water permeability) within the plane of a geotextile or geotextile-related product, is measured under varying normal compressive stresses, typical hydraulic gradients and defined contact surface.
-
product
Permeability Tester for Diapers
DRK357B-II
Shandong Drick Instruments Co., Ltd.
The diaper permeability tester is used to determine the absorption speed, re-permeability and permeability of diapers and other products.
-
product
Parallel 8-channel Hipot Tester
TH9010
Changzhou Tonghui Electronic Co., Ltd.
8-channel parallel output of withstand voltage, and each channel is non-interfering ■ Output: AC: 5kV/10mA; DC: 6kV/5mA ■ Insulation resistance test voltage: 0.10kV -1.00kV
-
product
Electric Vehicle Battery Cell Tester
MCV
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
product
AMIDA 2020XP Tester
AMIDA 2020XP CIS tester is the latest generation of CMOS image sensor-specific measuring instruments from Metatech. In addition to the original true and accurate measurement, the high-throughput mass production solution designed for the high-throughput inspection of image lens modules and camera lenses has been well received after nearly 20 years of mass production experience. First-class factories at home and abroad import production. AMIDA 2020XP CIS testing machine not only meets the customer's testing time and high output and accuracy requirements. Within the range of functional flexibility, users can customize their measurement requirements according to the definition of various sensors. AMIDA 2020XP CIS tester is a new generation of CMOS Image Sensor dedicated tester, which integrates DC open/short/leakage test, AC Pattern test and image test. It uses 180 Pin high-speed cable to connect to the test end
-
product
Standard Brinell Hardness Tester
BRIN400 Series
The Standard Brinell Hardness Tester - BRIN400 Series of closed loop Brinell hardness testers represent the latest in Brinell hardness testing technology. They are robust, reliable, proven and designed to meet a customer’s most demanding requirements in harsh industrial environments such as those found in foundries, forges and steelworks.
-
product
HDD Motor Testers
BK8015/BK8015A
The BK8015 HDD Mechanical Specifications Tester and the BK8015A HDD Circuit Specifications Tester were designed and manufactured by BaKo to test HDD motors as they come off the assembly line. The two machines are complementary, and were designed to test a complete set of HDD motor characteristics.
-
product
High Load Strength Tester
HLST1000Z
This tester measures the tensile or compressive strength of various samples
-
product
USB TESTER, 3-9V, 3A, WHITE
72-13540
*USB tester inspects USB charger & portable power source*Lightweight and portable*LCD backlight*High/low output voltage warning*10 sets of data memory
-
product
Capacitive Discharge Testers
For IEC Testing of residual voltage after plug disconnect. The CDT-240 disconnects the line at the voltage peak and analyzes results to the requirements of various Standards, allowing quick results. Scope output for viewing decay waveform. Presets for EN 61010, EN 60065, EN 60950, EN 60601-1 and EN60335. Recommendations for Pluggable Type B equipment. NIST calibration supplied; A2LA calibration available. 16A option for testing large equipment.
-
product
Random Pilling Tester
UI-TX08
Random Pilling Tester is a kind of pilling tester to determine textile fabric resistance to pilling, fuzzing and matting by tumbling randomly.
-
product
Circular Locus Tester
TF225
TESTEX Testing Equipment Systems Ltd.
Circular Locus Tester, to determine surface deterioration and quality of fabrics (wool, chemical fiber, mixed, kitted and woven fabrics). Using an active friction system, fabric is rubbed against a nylon brush and abrasive or an abrasive only under controlled conditions. Results of the test are achieved in minutes. The relative motion of the locus specimen grip and the abrasive platform is a circle with a relative speed of 60+/-1 r/min. The grip offers pressure to the specimen which is adjustable with a tolerance of +/-1%. For added control and safety, the machine is equipped with a self-stop switch.
-
product
Electrical Safety Testers- Hipots
Safety testers (also named hi-pot tester/hipot tester/hipot test) are designed to ensure safe operation of DUTs under various operating conditions and environment.GW Instek’s GPT-9900/GPT-9800/9600 series safety testers(hipot test) provide safe and quick measurement tools for AC/DC withstanding voltage tests, insulation resistance tests, and AC ground bond tests. Those tests are required by many international safety regulations such as CE, UL, VDE, and etc. We also have leakage current tester, GLC-9000, which supports all the major leakage current test standards for medical and general electronic equipment.
-
product
Tabletop Light Fastness Tester
TF419
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
product
Ultra-Compact Immunity Tester
AXOS8
The AXOS8 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips/Interrupts and AC/Surge Magnetic Field. The simplified user interface provides quick selection of tests and test levels, and even lets you change test parameters “on the fly” while running a test.The actual EUT power mains voltage and current are indicated in the display. Using the Electronic-Fuse function, the user can set an upper limit for EUT power mains current. This feature is useful to protect the EUT from unnecessary damage.Whether you test to the IEC 61000 series “CE Mark” standards, the IEC 60601 Medical Device standards, or any number of telecom and product specific standards, the AXOS8 tester is your one stop test station for everything from precompliance to full compliance to product development testing.A wide range of cost-efficient Coupling / Decoupling Networks for symmetrical and asymmetrical data- and signal-lines is available as an option.
-
product
Hardness Testers
We offer a comprehensive range of hardness testers for Rockwell, Brinell, and Microhardness testing on materials such as metals.
-
product
Adhesion Testers
From the largest man-made structures to the smallest household appliances, most manufactured products have a protective or cosmetic coating. Premature failure of this coating can, at the very least, result in additional costs of rework. Adhesion testing after the coating process will quantify the strength of the bond between substrate and coating, or between different coating layers or the cohesive strength of some substrates. Routine adhesion tests are used as part of inspection and maintenance procedures to help detect potential coating failures.
-
product
Waterproof Ozone Tester
ORPTestr 10
Large Display Screen - dual display LCD for enhanced readability, provides comprehensive meter information
-
product
IPTV Tester
NetProbe 2000 IPTV Analyzer
The NetProbe 2000 IPTV is a handheld IPTV tester that can emulate a set top box or passively monitor video channels in pass-thru mode. It can be used to turn up new service by auto scanning all channels and checking their quality or to troubleshoot the service. It is battery powered and easy to operate by a tier one technician.
-
product
Digital H.V. Insulation Tester(10kV)
6310 IN
Standard Electric Works Co., Ltd
● 2 Lines × 16 Characters LCD● Microprocessor-controlled● Tests insulation resistance up to 20 TΩ● 4 Insulation test voltages: 1000V, 2500V, 5000V, 10000V● AC / DC Voltmeter (30~600V)● Short-circuit current up to 5mA● PI (Polarization Index) indication● DAR (Dielectric Absorption Ratio) indication● Auto-ranging on all insulation ranges● Optical USB to RS-232 data transmission● Well isolated from contact● Well protected from surges● 2 built-in optical LEDs for data transfer● Visual and audio warning of external voltage presence (≥30Vac or ≥30Vdc)● Auto-hold function to freeze reading● Overload protection● Adjustable testing duration: 1~30 minutes● Internal memory for data storage● Displays testing duration for insulation measurement● Auto-off function● 200 measurement results can be saved in memory and recalled on
-
product
Countermeasures Sequential Timing & Amplitude Tester
C-STAT
C-STAT, or Countermeasures Sequential Timing and Amplitude Tester, is a Firing Pulse Interval Test Set, a suite of test components designed to analyze firing pulse timing and amplitudes from a CMDS system such as ALE-47.
-
product
IEC60065 Dielectric Strength Tester
PG-K02
Shenzhen Chuangxin Instruments Co., Ltd.
The IEC60065 Dielectric Strength Tester is mainly used for testing thin-layer insulation material electric strength.and IEC60065 Dielectric Strength Tester is with ISO17025 Calibration Certificate
