Patient Simulators
generate known values for any or all of the following medical equipment which measure: invasive blood pressure (IBP), Arrhythmias, Respiration, temperature and Fetal simulation.
-
Product
AC Load Simulating Inductors
-
Osborne designs our AC Inductors to provide the desired inductance and to perform effectively with the dissipation characteristics presented to the circuit. Dissipation characteristics depend on circuit current and operating frequency. The Osborne design approach is unique to the extent that we design for frequency effects. The resulting inductors deliver superior performance.
-
Product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
-
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
Product
Electronics Cooling Simulation Software
FloTHERM
-
Perform thermal analysis, create virtual models, and test design modifications of electronic equipment before physical prototyping. FloTHERM uses advanced CFD techniques to predict airflow, temperature, and heat transfer in components, boards, and complete systems, including racks and data centers. It''s also the industry''s best solution for integration with MCAD and EDA software.
-
Product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
-
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
Product
Infrared Simulation Services
-
INO offers a simulation service to assist with the hardware and software design of infrared and electro-optical devices. Precise performance predictions help integrators understand application requirements and bring application performance in line with client specificationsbefore the advance design and fabrication phases. For a minimal investment, infrared simulations help minimize risk in the early stages of development.
-
-
Product
Solar Simulator
Unisim
-
TS-Space Systems is the first company to pioneer the use of metal halide sources in solar simulators for photovoltaic testing. The high temporal stability and close spectral match combined with the ability to control the output spectrum via multiple separate wavebands means the Unisim solar simulator is the only solar research tool designed for the accurate measurement of multiple junction devices, including the new generation of four junction devices.As with all our Unisim solar simulators, they exceed the ASTM, IEC and JIS international standards for spectral match and temporal instability.Using the latest HMI and halogen luminaire technology, the Unisim solar simulator provides a highly stable area of illumination. The simulators also use cutting edge filter technology in order to provide the best spectral match available for AM0 and AM1.5. Further to this, the spectrum can be achieved via two, three or four separate spectral wavebands which allows a high degree of spectral control for research and development.Product support is very important to us. Training is provided at our premises where customers can take advantage of one-on-one tuition with the instrument designers and learn how to operate and maintain their tools. Extensive support via phone and email for the full lifetime of the instrument is included with every TS-Space Systems product.
-
Product
Steady State Solar Simulator
-
Our steady state solar simulators enable you to test and develop solar thermal collectors independent of weather and season, faster, more efficiently and more comprehensively than ever before. Both simulators are turnkey products, delivered 100 % ready to go!
-
Product
20KV 30KV Electrostatic Discharge ESD Simulator
20KV/ 30KV Electrostatic Discharge ESD Simulator
-
Shenzhen Chuangxin Instruments Co., Ltd.
ESD simulator (Electrostatic Discharge Generator or Electrostatic Gun) is in full compliance with IEC 61000-4-2, EN61000-4-2, ISO10605, GB/T17626.2, GB/T17215.301 and GB/T17215.322. The ESD generator is designed for the assessment of electrical and electronic equipment to withstand ESD performance. ESD-0230/ESD-0220 has LCD display in both English and Chinese, they equipped with an infrared remote control which can allow you do the test in some special place.
-
Product
Handheld ESD Simulator
-
Battery operated handheld ElectroStatic Discharge (ESD) generator up to 30kV.Discharge networks according to IEC 61000-4-2, ISO 10605, MIL-STD-461 CS118, DO-160 section 25 and many more standards.
-
Product
Type 2, PCMCIA Dual Redundant MIL-STD-1553 serial bus Simulator Analyzer Tester
PC401
-
MIL-STD-1553 A, B, & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester type 2 PCMCIA BUS Interface Card - The PC401 can be used for Validation Testing, ProductionTesting, full bus simulation and monitoring, as a generalpurpose 1553 interface or a stand alone bus Analyzer. Forprecise message scheduling and measurements, the Majorand minor frame times are independent of messagesequences or retransmissions on errors and the start of allcommand messages are independent of message length,response time or length of response. Message timing iscalibrated and RT responses have low jitter.
-
Product
Time-domain Field-Device-Circuit coupled simulator
EM-SUPREME®
-
Time-domain Field-Device-Circuit coupled simulator for modeling of passive structures, active components, and complete RF & millimeter-wave modules. EM-Supreme is used for EM modeling of power amplifiers, switches, filters, active antennas, and complete RF modules such as antenna-switch, switch-filter, switch-filter-amplifier, and front-end modules with no approximations.
-
Product
Target simulators
-
Simat simulator is an advanced hardware simulator capable to simulate in infrared range several targets on quasi uniform background. In detail Simat simulator is a modular image projector capable to simulate in infrared range variable intensity, variable angular size, variable spectrum, spatially and temporally dynamic airborne type targets on quasi uniform background. Basically the aim of Simat to enable simulation typical airborne targets like aircrafts or helicopters for infrared imaging sensors used for surveillance of these targets. Optionally Simat can be modernized to enable simulation in both IR and UV/visible ranges as the projectors are built using broadband reflective optical elements.
-
Product
Virtual Platform Development and Simulation
DEV
-
The Imperas Developer products consist of tools, models and infrastructure components critical for the high quality, rapid development and verification of embedded software, utilizing virtual platforms. The Developer products provide the necessary capabilities to develop platforms, including software simulation capability to execute embedded code on the platforms.
-
Product
Sunlite Solar Simulators
-
- Gen III Optics for High Efficiency Illuminati- Infinitely Adjustable Irradiance, Reproducibly Settable- Class A AM1.5G Spectral Match- ASTM Class A stability- 50×50 mm Class B uniformity- Manual Shutter Included, Electronic - Shutter Optional- Uninterrupted testing with the prealigned lamps- HEPA filtered air cooling
-
Product
2-CH MIL-STD-1553A/B Bus Simulator Module
1553 WA73A-455
-
The WA73A-455 MIL-STD-1553A/B Bus Simulator Module allows a system controller in an ATE system to communicate with and test devices that conform to the MIL-STD1553A/B data bus used in military aircraft and communications systems. Each of the WA73A-455's two channels operate as two separate and independent channels with their own VXIbus logical address, interrupts, and complete set of controls and indicators. As a result, each channel of the WA73A-455 is truly an independent instrument, and, therefore, individually programmable.
-
Product
PXI RTD Simulator Module, 8 Channel, PT500
40-263-402
Simulator
The 40-263-402 is an 8-channel PT500 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
Avionics Supply Simulation System
-
Spitzenberger & Spies GmbH & Co. KG
Simulation of voltage variations. Simulation of frequency variations. Creation of practical disruptions
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
Environmental Simulation Chambers
-
GTEMCELL , currently provide environmental test chambers made by LIB.Our standard range of test chambers includes bench top and floor standing models, across temperatures ranging between -65℃ and +150℃ (from -80℃ to +200℃ for specific applications), and humidities between 10% and 98% RH.
-
Product
Simulation Software and Test Solutions
Simcenter Software
-
Siemens Digital Industries Software
The Simcenter portfolio uniquely combines 1D simulation, 3D CAE and test to help you predict performance across all critical attributes earlier and throughout the entire product lifecycle. By combining physics-based simulations with insights gained from data analytics, Simcenter helps you optimize design and deliver innovations faster and with greater confidence.
-
Product
Boiler Auxiliaries Plant Control Simulator
MS 1300
-
BAPCON SIMULATOR is used to test and validate Boiler Auxiliaries Plant Control Unit (Sigma BAPCON). It has CAN interface for simulating inputs and it is a microprocessor based system.
-
Product
ARINC 664 Part 7 PXI Express Test & Simulation Instrument
PXIe-C664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K - Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
MIMIC® Simulator Suite
-
MIMIC Simulator creates a real world lab environment, with 100,000 devices, at a fraction of the cost of physical equipment. It provides an interactive hands-on lab for quality assurance, development, sales presentation, evaluation, deployment and training of enterprise management applications. Users create a customizable virtual environment populated with simulated routers, hubs, switches, WiFi/WiMAX/LTE devices, probes, cable modems, servers and workstations.
-
Product
Simulation Softwar
Opixs
-
Opixs is Fluxim’s latest simulation software for display research and development. It enables users to explore various pixel designs, quantify their power consumption and colour coverage, taking into account application-relevant displayed content. By making the trade-off between efficiency and technological complexity visible, Opixs helps accelerate innovation in OLED, QLED, microLED, and other advanced display technologies.
-
Product
HUFF-DUFF SIMULATOR
HF/DF
-
HUFF-DUFF is a High Frequency Direction Finding radio system used during WWII to locate German Submarines for destruction. This device simulates the receiver signals including code encripted transmission for display on any oscilloscope for interactive museum displays.
-
Product
Motion Simulation
-
Exail's motion simulators are at the forefront of calibrating and testing inertial sensors, navigation systems, and optronic payloads across diverse applications, from traditional land vehicles and aircraft to emerging sectors like autonomous vehicles and wearables. With 60 years of expertise, Exail's rate tables deliver unparalleled performance, accuracy, and reliability, offering a cost-effective solution tailored to meet customer needs at every stage of product development. From concept to maintenance, Exail provides comprehensive support, ensuring the success of each project
-
Product
Liquid Battery Test Cell (Coin Cell Simulator)
LBT1
-
A liquid battery test cell designed for electrochemical research, battery experiments, and laboratory material evaluation, providing reliable sealing and repeatable testing performance.
-
Product
Engine Sensor Simulation Card
CP-ENG-SIM
-
The CP-ENG-SIM Engine Sensor Simulation PCIe Card is an FPGA-based I/O solution designed for real-time simulation of engine and vehicle sensor signals. Built for Hardware-in-the-Loop (HIL) environments, the card enables accurate emulation of crank, cam, ignition, fuel injection, and other sensor signals used in engine control systems.
-
Product
PXI/PXIe Analog Output/Current Loop Simulator Module - 16 Channel
43-765-001
Analog Output Module
The 41/43-765-001 is a PXI/PXIe 16-channel Analog Output Module designed to meet the requirements of industrial control applications utilising current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signalling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
