Global Positioning System
Global Positioning System is used for determining one's precise location and providing a highly accurate time reference almost anywhere on Earth.
-
Product
MWIR Systems
-
L3 Cincinnati Electronics’ high-performance cooled mid-wave (3.5 – 5.0 µm) IR imagers are based on our patented InSb focal plane array architecture. Ideal for all combat conditions, L3 Cincinnati Electronics technology improves situational awareness in combat intelligence, sighting & tracking systems, threat deterrence and perimeter & border security with all-weather observation, day or night. These IR sensors can be utilized in urban, rural and remote situations where there are extreme climatic and terrain conditions. Well-suited for fixed or portable payloads, these imaging systems offer a substantially lower total life-cycle cost in comparison to other commercial IR imaging sensors.
-
Product
Test System
LB301
-
Computer Gesteuerte Systeme GmbH
The system is pin and software compatible to the larger test systems LB302 / 303. Due to the fewer needed I/Os, the tester features the compact G6 receiver (Virginia Panel Cooperation) compared to the larger G12 of the other tester versions. The LB301 is equipped with a 2kW power supply and can control one load box.
-
Product
Position Sensors
-
Position sensors are made of a specially-manufactured and calibrated measuring cable and a highly accurate graduated drum. They are very easy to install and are ready for use in a very short time.
-
Product
Thermal Imaging System for Electronics Testing
ETS320
-
Whether the goal is product testing or scientific research, heat can be an important indicator of how a system is functioning. The FLIR ETS320 is a non-contact thermal measurement system that pairs a high-sensitivity infrared camera with an integrated stand, for hands-free measurement of printed circuit boards and other small electronics.
-
Product
Vibration Test Systems
G-5 Series
-
Both Shock tests at from relatively high acceleration(max. 4900m/s2 -500G) to low acceleration with wide pulse width, difficult to achieve with conventional Shock Test Systems and Vibration tests for not only IEC, MIL and JIS but also requiring higher acceleration, velocity and displacement than ordinary VTSs can be carried out with one system.
-
Product
System Module AXIe-0
SMGS AXIe-0
-
The SMGS AXIe-0 module is a 14-port unmanaged Ethernet switch. One of the ports of this switch is brought out to the front panel of the module and is used for interaction via the Ethernet interface with external equipment (PC, Ethernet local network), the remaining 13 ports of the switch are used for interaction with the instrument modules of the AXIe-0 standard crate. This architecture of the module allows for the interaction of an external PC with any instrumental module of the AXIe-0 standard crate.
-
Product
Raman Spectrometer System
IndiRAM CTR Mini Series
Spectrometer
IndiRAMTMCTR-mini Series Raman Spectrometer system is one of the best solution for carrying out reaction-monitoring or insitu analysis of the samples as it is a compact system capable of moving oform one place to another but at the same time maintaining high resolution and SNR
-
Product
Marine Logging System
SuperSting Marine
-
The SuperSting Marine continuously records and stores data from a GPS receiver. Current is injected every 3 seconds and 8 apparent resistivity values representing 8 depth levels are read for each current injection. Depth of penetration depends on length of the cable and array type. Typically you will see down to aproximately 20% of the electrode spread length.
-
Product
System Accessories
-
To support the full need of the application Elma offers a comprehensive range of system level accessories to include: I/O solutions, HMI Displays, System/Power Management, Test/Development Boards, and Mechanical Mounting products.
-
Product
Motor Stator Test System
Chroma 1920
-
Chroma Systems Solutions, Inc.
For electrical safety and quality testing functions of motor stator coils
-
Product
IR Inspection System
EVG®20
-
The EVG 20 offers a fast inspection method, especially for fusion bonded wafers. A live imageof the entire wafer via IR transmission supports void detection down to a radius of 0.5 mm. The infrared inspection system is a perfect match for fusion bonding processes either as the stand-alone EVG 20 tool or as a station in EVG''s integrated bonding systems.
-
Product
Power Transmission Line Inspection System
-
Shandong Senter Electronic Co., Ltd
With the aid of high-end technology and equipment, Senter Electronic manufactures and trades high-tech power transmission line inspection system with low price. And we are known as one of the leading such manufacturers and suppliers in China for our quality products and good service. Welcome to buy the power transmission line inspection system with our factory.
-
Product
Cyber Protection System
-
Raytheon’s Cyber Protection System enables enterprises to go beyond traditional CSOC monitoring and establish a response center capable of situational awareness, proactive defense and rapid response. Cyber test ranges: Test the cyber resilience of hardware, software, and networks. Penetration/Malware/Forensics Fly Away Kits: Provide mobile environments to perform testing and analysis at remote facilities. Lab environments: Analyze malware, perform penetration testing and conduct forensics at enterprise scale so analysts can determine the best way to manage them.
-
Product
Multi-Stage Functional Test Systems
-
Circuit Check’s bi-level and multi-stage fixtures combine multiple test levels in a single fixture using controlled actuation and selected probe travels for powered and unpowered tests.
-
Product
Cloud-Based One System Platform
VeSion
-
VeEX''s VeSion is a Cloud-Based, One System Platform, representing the next step in innovation for Network Monitoring. VeSion integrates RFmonitoring systems (Return and Forward), advanced DOCSIS Monitoring, DOCSIS Burst Demodulation, Sweep, Ethernet, MPEG, and Workflow and Asset management system, all under one umbrella. VeSion''s one system concept reduces network troubleshooting and problem resolution time significantly.
-
Product
Visible / Infrared / Imaging Test System
System 1808
-
Testing Low-voltage CCDs and IR FPAs; Military, science-grade and medical CCDs or IR FPAs; CMOS ROICs and multiplexers; CMOS sensors. Whether your application is characterizing a massive mosaic of CCDs for the next great observatory, designing a faster FLIR for a weapons-guidance system, or production-testing a CMOS image sensor for a digital camera, Pulse Instruments can supply you with a fully-integrated test system that allows you to focus on your your device, not on your test system.
-
Product
Dilution-Extractive System
ML675
-
The Teledyne ML®675 dilution-extractive system can be used in 40CFR75, 40CFR60, 40CFR63, and process control applications. In this system, sample is prepared for analysis by diluting stack gas with clean, dry instrument air at the probe location. Since no moisture is removed with dilution, measurements for SO2, NOx, CO, THC and CO2 are made on a wet basis.
-
Product
Advanced Line Protection System
ALPS
-
ALPS is a multi-function digital protective relay system intended toprovide distance protection for HV or EHV transmission lines. It maybe applied on or adjacent to series compensated lines. It is availablefor single or three phase tripping applications. Typical operatingtimes are to 1 cycle.
-
Product
Ground-Fault Products for Solidly Grounded Systems
-
Ground-fault products are used to monitor grounded systems (ungrounded and grounded) for fault currents or residual currents. The sum of all conductors except the protective earth conductor is measured by means of measuring current transformers.In general, ground-fault monitors (RCM - residual current monitors) are used to send a message to the user even before reaching the shutdown threshold of the GFCI. Ground-fault monitors detect deteriorations of the insulation level at an early stage and in a reliable way.
-
Product
Noise Monitoring System
NoiseTutor
-
Continuous monitoring of environmental data in remote areas has always presented a unique set of challenges. Typical solutions involve complex installations, frequent visits to remote locations to keep the system fully operational and require expert level attention to retrieve and share data amongst customers, consultants and project leads.
-
Product
Midi Systems
-
MIDI systems provide an efficient solution for customers seeking a Box PC with wide temperature performance and abundant I/O. MIDI systems feature expansion-ready front panels with removable cover plates to expose additional connector cutouts. The enclosure can easily accommodate up to two additional PC/104 style I/O modules or PCIe MiniCards. The cover plate provides ample cooling for our rugged conduction-cooled SBCs. Table-top, wall mount, and DIN rail mounting options are all included.
-
Product
Battery and DC System Testing
-
HAOMAI Electric Test Equipment Co., Ltd.
Testing for battery and DC power systems.
-
Product
Machine Vision System
CVX Series
-
he CVX Series is loaded with powerful features that support GLOBAL STANDARDS in machine vision inspection. State-of-the-art algorithms, that can be set by any user, ensure quick setup and long-term reliability. The best solution can be selected from a variety of options. No experience required to select lighing! - newly-developed, revolutionary Lumitrax function. 3D measurement. Ultra high-resolution 21 megapixel camera
-
Product
Non-contacting Position Sensors
-
For use in harsh environments, Vishay offers non-contacting position sensors based on Hall Effect technology. Linear displacement, rotational (single- and multi-turn), and kit design options all provide a full 360° measurement range with no dead angles and very long life, since there is no wear and tear on sensor elements. Applications for Vishay’s non-contacting position sensors include any system where vibration, shock, or dithering is to be expected, such as embedded applications in vehicles.
-
Product
Engineered Systems
-
AMETEK Programmable Power, Inc.
When a catalog product cannot completely satisfy a requirement, AMETEK Programmable Power's Solutions Business provides custom power supply systems and integrations. The solutions range from OEM integration for medical and semiconductor industries to modular avionics ATE power subsystems to turnkey solar array simulators for satellites. We also can modify power supplies to meet your application requirements.
-
Product
Automated Liquid Handling System
FlowCam®ALH
-
Yokogawa Fluid Imaging Technologies, Inc.
The FlowCam® ALH - Automated Liquid Handling system from Fluid Imaging Technologies integrates with the FlowCam® 8100 for uninterrupted processing of samples.
-
Product
Fiber Strain Measurement System
SPL500
-
The SPL500 is a fiber strain measurement system that measures fiber elongation and attenuation simultaneously during mechanical stressing of the cable. The SPL500 is designed to produce accurate measurements quickly and with confidence.
-
Product
Telemetry System for Electrics
HTS-SS Blue
-
Our HTS-SS Blue sensor station system provides comprehensive telemetry information about your electric-powered aircraft and is compatible with the HTS-Volt, HTS-GPS, HTS-TEMP, HTS-ORPM, HTS-MRPM, HTS-C200 and HTS-C50 suite of sensors.
-
Product
Compact and Flexible Measurement System
Loggito
-
The Loggito series is a new compact and flexible measurement system for data acquisition Industry IoT. It enables inexpensive connectivity of decentralised measuring points for both low channel data logging and complex acquisition systems.
-
Product
Engine Test Systems
TITAN Engine
-
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
