Filter Results By:
Products
Applications
Manufacturers
-
product
Clamp Earth Resistance Testers
Is used for earth resistance test. This meter uses an EBTN screen with a dual display function (the resistance & current displayed). It also has functions such as a real-time clock, data storage, data review, alarm, and automatic shutdown.
-
product
Near Field Probes 1GHz - 10 GHz
SX set
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
product
ADC 12-bit @ 2.6 GSPS and DAC 14-bit @ 5.6 GSPS, FMC
FMC216
The FMC216 is an FPGA Mezzanine Card (FMC) per VITA 57 specification. The FMC216 utilizes AD9625 ADCs providing 12-bit conversion rates of up to 2.6 GSPS and a DAC AD9129 providing 14-bit conversion rates of up to 5.6 GSPS. The analog input/output, digital output, clock and trigger interfaces of the FMC216 are routed via SSMC connectors. The internal clock frequency is programmable and the clock is capable of locking to an external reference.
-
product
High Performance Analog & Mixed Signal Test Solutions
Applicos
Effective mixed-signal test solutions demand know-how and experience. Low level analog signals need to be stimulated and analyzed near fast switching digital logic. Cross talk, magnetic fields, clock jitter, ground noise and non-linearity of components, are just a few of the problems that must be addressed. Applicos knows what it takes to design and produce high quality mixed-signal test solutions. They have been servicing the mixed-signal test industry since 1993 and have established a distinguished reputation for providing our customers with high performance, cost effective solutions. In 2018 we acquired Applicos B.V. to extend our portfolio for the ATE business.
-
product
Dual Channel Driver Card
42460
Two channels of 32 MHz clock drivers with up to 20 volt amplitude. The output voltage range is ±20 V, with independent high and low voltage settings. The inputs to the Card can be optically isolated. The card also contains voltage and current sense capability, which allows muxing of the current or voltage output measurements from all the Driver Channels in the system to a single DVM. The card allows independent programming of the rise and fall time of each channel one nanosecond increments.
-
product
PCI, PCI Express and USB radio clocks
Meinberg Funkuhren GmbH & Co. KG
Although the PCI Express is PCI-compliant, PCIe cards are based on a different concept. Less lines are used to transfer the data, for example in the case of PCI plug-in cards.
-
product
Digital Thermometer
ST-2
In / out temperature measurement. Clock function display. Super-thin design. Measurement range: -50℃∽+70℃Distinguish: >-20℃ is 0.1℃ ≤-20℃ is 1.0℃Accuracy:±1℃ Power: DC1.5V, battery LR44Product size: 56.5×37.8×11.3mm Screen size: 46.7×21.2mm
-
product
Logic Analyzer
GoLogicXL-36
Logic analyzers and oscilloscopes offering fast sample rates and large memory depths are required to debug and test modern electronics. The GoLogicXL captures a very large window of bus activity using sample depths up to 1 billion samples. 4 GHz sampling rates expose the finest details in your signals. 1 GHz Transitional sampling provides the optimum method to capture fast data bursts separated by seconds, minutes, or even hours of bus inactivity. The GoLogicXL State analysis can also synchronize with single-data-rate 300 MHz SDR clocks, and double-date-rate 250 MHz DDR clocks (500 MHz effective).
-
product
GPS Synchronized Clocks
Brandywine Communications offers high quality time and frequency GPS Synchronized clocks with budget friendly costs in a variety of formats such as the NFS-220 and the NFS-220 plus. Built at our ISO9001 accredited design and manufacturing facility in Tustin, CA, these U.S. made time and frequency standards incorporate a GPS receiver which continuously calibrates the internal precision clock to provide both time of day and frequency in a variety of output formats and interfaces.
-
product
PCIe Digital Waveform Acquisition with Programmable Threshold - 720 MBit/s Internal Sampling Rate Timing, 700 MBit/s External State Clock
M4I.7730-X8
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
product
SSA-J Precision Clock Jitter Analysis Software
E5001A
To meet the demanding needs of today's advanced digital communication systems, Keysight offers Precision Clock Jitter Analysis software (E5001A SSA-J) for more precise and accurate characterization and evaluation of clock-signal jitter.
-
product
Demonstration Board
SAMPULSE20x2
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
product
Clock and Data Recovery/Retiming
Analog Devices provides single rate, multiple rate, and continuous tuning clock and data recovery (CDR) ICs for metro, long haul, DWDM, FSO, instrumentation, and other applications. Our any rate CDR ICs allow easy integration into protocol agnostic applications, automatically locking onto incoming data streams at any rate, from 10 Mbps to 2.7 Gbps or from 6.5 Mbps to 11.3 Gbps, without the aid of a reference clock while reporting the acquired data rate over the I2C interface. With a proprietary dual loop design, our any rate CDR ICs feature fast locking with superior jitter performance.
-
product
Multifunction Analog I/O Board
104-AIO12-8
*Eight true differential inputs, or eight single-ended inputs optional*Programmable input ranges of: 0-5V, 0-10V, ±5V, ±10V*100KHz sampling rate*On-board pacer clock and counter timers*Four double-buffered analog outputs*Jumper selectable output ranges of: 0-5V, 0-10V, ±5V, ±10V*24 digital I/O lines, type 82C55 with change of state detect on port C, buffers on ports A & B*Flexible configurations to suit your needs
-
product
Multicoupler
Receiver (RX) multicoupler by novotronik are used whenever a common signal from antennas, signal generators or reference clocks has to be distributed to several radio receivers, spectrum analysers or radio scanners. Incoming signals are transmitted without attenuation losses. In addition to our standardized RF devices, we also know to convince in the realization of your individual requirements.
-
product
6 Channel ADC FMC Module
ADCFN06 – HPC
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN06 is a six channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides single-ended analog input and 16-bit single-ended output with 20-25MHz sampling speed based on ADI AD9650. A DC coupled input is supported. Single-ended external clock, differential external clock or an internal clock from the FMC carrier board can be selected at the FMC for the AD converter through fine clock generator ADI AD9518-3.
-
product
Analog to Digital Converter
high-linearity, ultra-low power, dual-channel, 12-bit, 50-MSPS to 160-MSPS, analog-to-digital converter (ADC) family. The devices are designed specifically to support demanding, high input frequency signals with large dynamic range requirements. A clock input divider allows more flexibility for system clock architecture design and the SYSREF input
-
product
1U 19” Edge Server With 4th Gen Intel® Xeon® Processor Scalable Family Processor
MECS-7120
- 1U 19” Edge Server with 4th Gen Intel® Xeon® Processor Scalable Family Processor- 6x DDR5 DIMMs, 4800MT/s (6 channels, 1DPC)- On-board 2x 25G SFP28 Ethernet ports- 1U 19’’ rackmount form factor for telecom infrastructure deployment- RunBMC with AST2600, IPMI v2.0/Redfish compliant- Optional clock module to provide time sync from GNSS- Designed for 5G: DU, DU+CU, DU+CU+MEC, MEC, uCPE, industrial edge computing
-
product
250MS/s PCIBus Arbitrary Waveform Generator
5351
Model 5351, is a single-channel frequency agile waveform synthesizer that combines industry leading performance, frequency agility and modulation capability in a stand-alone, modular product. Having 1.5Hz to 250MHz clock and 16-bit vertical DAC resolution provides the test stimuli required for the decades to come. It can be used as an arbitrary waveform generator, modulating generator, as well as function and pulse generator.
-
product
FMC-HPC ADC Board
FMC123
Sundance Multiprocessor Technology Ltd.
The FMC123 provides four 16-bit A/D channels up to 1Gsps. The design is based on Texas Instruments’ ADS54J60 Analog-to-Digital converter. The sample clock can be supplied externally through a coaxial connection or supplied by an internal clock source (optionally locked to an external reference) for multi-channel synchronization. An external trigger input is available for timing synchronization. The FMC123 is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
product
28/45 GHz Dual Optical Channel DCA-M with Option CDR
N1092B
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, fast sampling rates for high throughput, and integrated clock recovery available.
-
product
PCI Express 8-Port
7804ec
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
product
PCI Express A/D Board
AD16-250 - Dual/Quad 16 bit, 250 MS/s
The AD16-250 series has two or four 250 MS/sec 16-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual and quad channel boards sample concurrently at the input clock frequency, and can also be software selected to run in single channel mode, providing up to four (4) times the effective memory depth.
-
product
Optical Lattice Clock
Our strontium lattice clock project aims to create the world’s first commercially available fully integrated optical frequency atomic clock. The clock will be compact, transportable, easy to use and based on optical lattice technology enabled by the SolsTiS. The strontium lattice clock will achieve frequency uncertainties below 10-17, a level unprecedented on the global market.
-
product
Time Interval Counter PXI Card
GTX22x0
The GTX22x0 family of PXI universal time interval counters offer many of the measurement and timing functions of high-end stand-alone frequency counters, including accumulate, auto ratio, frequency, fast frequency (GTX2220 and GTX2230 only), period, ratio, single period, test clock, time interval, time interval delay, totalize, totalize gated, totalize gated once, & pulse width.
-
product
PCI Express A/D Board
AD8-1800 Series - Dual 8 bit, 1.8 GS/s
The AD8-1800 series has one or two 1800 MS/sec 8-bit ADCs, 8GB of on-board memory and the ability to transfer data directly into the host computer's memory at over 1 GB/sec. Streaming to the host computer can be performed simultaneously with acquisition to on-board memory, increasing the effective acquisition length by using the host computer's memory. Dual channel boards sample concurrently at twice the input clock frequency, and can also be software selected to run in single channel mode, providing twice the effective memory depth.
-
product
8-Slot Fully Hybrid PXIe Chassis
42-924-001
Our 42-924 PXIe Chassis provides seven hybrid compatible slots for application flexibility. The chassis utilizes a single PCI segment with a dedicated PCIe-to-PCI bridge module for the hybrid slots. The PXI specific high accuracy clocks and trigger signals are generated and controlled by an independent clock module attached to the rear of the backplane. This hybrid chassis supports the latest generation (Gen 3) PXIe modules. The chassis is fitted with a 400W industrial grade power supply mounted at the rear of the unit with sufficient capacity to support PXI modules with very high current demands.
-
product
Antenna-integrated PTP Grandmaster Clock
OTMC 100
OTMC 100 antenna-integrated PTP Grandmaster Clocks provide you with a quick and easy solution to time synchronize inteligent electronic devices, computers and measurement equipment connected via Ethernet.
-
product
Indoor Outdoor Thermometer
Model 304
1. Time, date display.2. Time alarm clock every day.3. 12/24 hours system clock.4. ℃ /℉ indoor/outdoor temperature display.5. Indoor/outdoor temperature trend display6. Max/Min indoor/outdoor temperature display7. Temperature measure range: -20~50℃8. Temperature resolution: 0.1℃9. Temperature accuracy: ±1℃10. Measuring period: 20 sec11. Power: 1.5V (AAA or 7# battery)
-
product
PCIe LVDS Digital Waveform Acquisition - 250 MBit/s Internal Sampling Rate Timing, 250 MBit/s External State Clock
M4I.7725-X8
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
