Mixed-Signal Test
See Also: Mixed Signal, Mixed Signal ATE, Mixed Signal Oscilloscopes, Mixed Signal Testers, MIxed Signal Test Systems
-
Product
Mixed Signal Test Systems
MTS1000i
-
The MTS-1000i is lowest cost platform available in the MTS series of ATE. It has a reduced platform size compared to the MTS-2010i & MTS-1020i, reduced power supplies, and 4 slots. It is mainly intended for single site testing. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Digital and Mixed-Signal Test Solutions
-
A digital device processes electronic signals that represent either a one (on) or a zero (off). The ‘ones’ and ‘zeros’ represent data. Each one or zero is referred to as a bit and a group of 8 bits equals a byte
-
Product
Mixed Signal Test Systems
MTS1010i
-
The MTS-1010i is a more economical version of the MTS-2010i & MTS-1020i testers. It has a reduced platform size and reduced power supplies. Like the other testers in the MTS family it is a highly cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
Mixed signal LSI test system
-
Multi-pin type model is now launched in WL27 Logic/Power mixed LSI test system.This system is suitable for multi-site test in A/D mixed device such as automotive・motor driver IC. It’s a high throughput and cost performance mixed signal LSI test system.
-
Product
Mixed Signal Battery Test System
Test System
The Mixed-Signal Battery-Test System is an automated test platform designed to meet today’s advanced battery test requirements. The platform is ideal for testing a range of battery cells and packs, and can be used in applications such as research and design, quality control, and end-of-line manufacturing. Its distributed architecture provides a scalable solution with configurable system components to accommodate specific applications.
-
Product
High Performance Analog & Mixed Signal Test Solutions
Applicos
-
Effective mixed-signal test solutions demand know-how and experience. Low level analog signals need to be stimulated and analyzed near fast switching digital logic. Cross talk, magnetic fields, clock jitter, ground noise and non-linearity of components, are just a few of the problems that must be addressed. Applicos knows what it takes to design and produce high quality mixed-signal test solutions. They have been servicing the mixed-signal test industry since 1993 and have established a distinguished reputation for providing our customers with high performance, cost effective solutions. In 2018 we acquired Applicos B.V. to extend our portfolio for the ATE business.
-
Product
Mixed Signal Test Systems
MTS1020i
-
The MTS-1020i is a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process
-
Product
Mixed Signal Test Systems
MTS2010i
-
The MTS-2010i are a cost effective production ATE designed for testing high-volume linear and mixed signal semiconductor devices (Op Amps, high-voltage drivers, DAC, ADC, etc.), both at the wafer sort and final test stages of the manufacturing process.
-
Product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
test
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
Product
Test Management Software
ActivATE™
test
Easily create and run robust test programs in semiconductor automated test systems with ActivATE™ test management software. Designed by test engineers for test engineers, ActivATE™ tames automated test complexities with elegant simplicity.
-
Product
Interactive Benchtop Test
test
Strict time-to-market deadlines make it vital to efficiently debug and validate product designs. Virtual instrumentation provides a unified interface that gives engineers an advantage over traditional box instruments.
-
Product
NI Real-Time Test Cell Reference System
778820-35
test
DIAdem Advanced with DAC Bundle, Perpetual License, Include 1 Year SSP
-
Product
Wireless Test Standards Software
test
Generate and analyze signals for cellular and connectivity standards with NI PXI RF instrumentationPerform advanced automated test with the easy-to-use NI-RFmx software APISave on all NI RF wireless test software under a single license
-
Product
Semiconductors Testing
test
Our Testers support the production lines of variety of products such as 40/100 GBps Mux/DeMux, LNA, WiMAX RF Transceivers, Microwave & Millimeter Wave components. This high reliability products are being used in (a) Networking & Communications (b) Consumer Electronics (c) Military & Space
-
Product
Advanced SoC Test System
3680
Test System
The Chroma 3680 is an advanced SoC test system with data rate up to 1Gbps. The Chroma 3680 is capable of conducting parallel tests on multiple chips to meet the digital and analog IC testing requirements, with applications including MCU, digital audio, digital TV, set-top box, DSP, network processor, field programmable gate array (FPGA) and consumer electronics.
-
Product
CPE Design Verification System
Jupiter 310
Test System
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
Product
Explosive Test Site Range Instrumentation
test
Firesets, CDU’s EDU’s, Delay generators, firing panels, and custom instruments. Fiber-optic and computer-control options.
-
Product
Mixed Signal, Multi-Functional Test Module
PXIe-ScanIO-112
Test Module
The PXIe-ScanIO-112 delivers a powerful combination of digital, analog, and AC-coupled testing in a single PXIe module. With 104 boundary-scan controllable digital I/O channels and 8 analog I/O channels ranging from –15V to +15V, engineers gain the flexibility to test a wide variety of board-level designs. The module supports IEEE-1149.6 AC-coupled interconnect testing, configurable single-ended and differential pin operation, and integrates seamlessly with the Corelis ScanExpress™ suite.
-
Product
Design for Testability (DFT Test)
test
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
Product
Configurable Functional Test System
ATS-5000
Test System
Maximize the uptime of your most critical electronics with the ATS-5000 Functional Test System from Astronics Test Systems. Deployed globally for more than 20 years, the newest version of this tester provides a configurable, affordable solution that delivers just enough test.
-
Product
Automated Compliance and Device Characterization Tests
N5990A
Test Platform
The Keysight N5990A test automation software platform is the most powerful tool for serial and multi-lane gigabit testing. It is the unique universal platform for testing a wide range of digital buses such as PCI Express, USB, HDMI or MIPI. The same graphical user interface and operating principles are used for all applications. This boosts productivity, especially when testing devices which support multiple digital buses. The N5990A can be tailored to your individual test needs with the flexible test sequenzer and controls all instruments needed for your tests. The configurable database interface of the N5990A test automation platform enables the convenient storage of all test results. A web interface allows an effective and easy operation. Custom calibration and test procedures can be implemented easily with User Programming.
-
Product
Test Fixture
16047E
Test Fixture
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
Product
NI Automated Test Software Suite
test
The NI Automated Test Software Suite features all three NI IDEs and NI's most popular application software and add-ons specifically for building your automated test system with confidence. This package offers the power of LabVIEW, LabWindows/CVI, and Measurement Studio combined with the TestStand ready-to-run, test executive and the Switch Executive intelligent switch management application
-
Product
Regenerative Battery Pack Test System
17040E
Test System
High-power testing equipment up to 1,700V/ 4800A/ 1.2MW Multiple safety protections for personnel safety risk management and control of battery testing Flexible Integration for automated battery verification solutions
-
Product
In-Line RF Test Platform
AR925
Test Platform
This functional and RF test platform combines outstanding productivity with substantial equipment savings. The Faraday chamber of the fixture comes with an interchangeable cassette to minimize the testing cost of each new product
-
Product
Parallel Electrode SMD Test Fixture, DC To 3 GHz
16196D
Test Fixture
The 16196D surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results – reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement – now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
Product
Dielectric Test Fixture
16451B
Test Fixture
The 16451B is used to evaluate the dielectric constant of solid dielectric materials accurately, and complies with ASTM D150. The 16451B employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixture.
-
Product
6TL36 Inline Handler
AM304
Test Handler
Test handler 6TL36 able to test DUTs inside Faraday ChamberDual line (bypass)
-
Product
True Concurrent Test
TestStation Duo
Test System
The TestStation Duo is a true concurrent test system with independent test modules providing fast in-circuit test throughput and lowering high-volume production costs.It effectively doubles the test throughput of conventional in-circuit test systems, without doubling capital equipment costs or increasing manufacturing floor space, by combining two complete and independent test modules inside a single tester frame.
-
Product
Headlamp Test Platform
Test Platform
Leverage 25+ years of automotive test experience, with the specialized design and manufacturing of automotive lighting testers. Using specialized know-how in this field, including photometric, electro-mechanical equipment and software solutions, accelerate your time to market with a higher quality product.
