PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
product
High-Density 128-CH Isolated DIO/DI/DO PCI Cards
PCI-7442/7443/7444
Responding to the industry"s need for high-density digital input/output modules, the ADLINK PCI-7442/7443/7444 DIO card series delivers up to 128 opto-isolated channels for a wide range of demanding PCI-based applications. The PCI-7442/7443/7444 series comes with 64 (PCI-7442) or 128 (PCI-7443) opto-isolated digital inputs and 64 (PCI-7442) or 128 (PCI-7444) opto-isolated digital outputs. With a 1250 VRMS (excluding cables) channel-to-system isolation protection, these cards are shielded from damage caused by accidental contact with external voltage while promoting simple ground connections. All input channels are identical non-polarity with each line isolated and suited to collect digital inputs even at high-noise environments. Featuring a Change-of-State (COS) interrupt function, the PCI-7442/PCI-7443 instantly generates an interrupt request to the PCI controller when it detects a sharp change in the logical state of any of its digital inputs.
-
product
Dual LGA3647-P0 Intel® Xeon®Scalable EATX Server Board with 12 DDR4, 5 PCIe x16 + 1 PCIe x8 + 1 PCI, 8 SATA3, 6 USB3.0, Dual 10GbE, IPMI
ASMB-925
- EATX Server Board with dual Xeon Scalable processors- DDR4 2933MHz RDIMM up to 1.5TB, support Intel Optane DC Persistent Memory- Five PCIe x16 (Gen3), one PCIe x8 (Gen3), and one PCI slot- Intel® X557-AT2 dual 10GbE ports- Eight SATA3.0 and six USB3.0 ports- 0 ~ 40 °C ambient operation temperature range
-
product
Full-size PCI Express Mini Module with 2 Gigabit LAN
AX92918
Supports 10/100/1000 Mbps transfer rates, Supports Wake-on LAN, Supports PXE Boot ROM, Intel® i210IT controller, 51 x 30 mm
-
product
Fanless Embedded System With Intel® Core™ I5-7300U/i3-7100U & Celeron® 3965U, 2 HDMI, 2 GbE LAN, 4 USB 3.0 And PCI Express Mini Card Slot
eBOX560-512-FL
The eBOX560-512-FL is powered by the Intel® Core™ i5-7300U/i3-7100U or Celeron® 3965U processor. To enhance system efficiency, the embedded box PC supports one 260-pin DDR4-2133 SO-DIMM socket with up to 16 GB system memory. Two HDMI ports with up to 4K resolution are supported for dual independent display applications. The palm-sized fanless embedded system is dedicated to smart factory automation, thin clients, industrial controller system, digital signage and retail equipment. Axiomtek's eBOX560-512-FL was designed to operate reliably in industrial and embedded application environments. It is enclosed in IP40-rated heavy-duty aluminum extrusion and steel enclosure and offers a wide operating temperature range from -10°C ~ +50°C (+14°F ~ +122°F) and up to 3G vibration endurance.
-
product
PCI Strain Gauge Simulator Card, 4-Channel, 1.5k
50-265-404
Designed to simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
product
DAQ FMC Modules
Sundance Multiprocessor Technology Ltd.
FMC Modules with both Analog to Digital and Digital to Analog sections.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 65.5k Ohm
50-294-033
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
3U Rackmount Appliance for PCI Express® Gen5
R300-G5 Pro
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols.
-
product
Passive XMC-to-PCI Express Adapter
5934
The Technobox, Inc. P/N 5934 is designed to adapt a single-wide XMC card to a 4X PCI Express slot. The 5934 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
product
Flexible x1 PCI Express to 3 MiniPCI Splitter
SKU-070-XX
Flexible x1 PCI Express to 3 MiniPCI Splitter was designed to expand your modern motherboard (ATX, mini ATX etc.) that lacks a MiniPCI interface. It allows you to connect up to three 124-pin MiniPCI add-in boards to your motherboard’s standard PCI Express connector.Splitter includes 3 MiniPCI adapter boards, x1 PCI Express host board and 3 flat PCI Express cables.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm - SPST
50-294-132
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Basic 3U VPX-to-PCI Express (PCIe/PCI-e) Adapter
8462
The Technobox, Inc. P/N 8462 is a 3U VPX-to-PCI Express (PCIe) adapter that provides a convenient and cost-effective means for developing 3U VPX boards in a personal computer environment. It can also be used for production testing of 3U VPX boards. The adapter is a half-length PCIe card with the VPX card under test mounted close to the PCIe edge fingers to minimize signal lengths. When seated in a PC motherboard, the VPX card primary side faces upward to allow convenient access to components.
-
product
PCI Express 6 Base Specification Receiver Test Automation
N5991PB6A
The N5991PB6A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 6.0 ASICs
-
product
PCI Express 4 M.2 Receiver Test Automation
N5991PM4A
The N5991PM4A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express M.2 devices and hosts at 8 GT/s.
-
product
6U Compact PCI® Single Board Computer
CP62007N
LinkedHope Intelligent Technologies Co.,Ltd.
CP62007N is a 6U CompactPCI® single board computer designed by LinkedHope® based on Intel® QM87 chipset. The compact and space-saving processor board meets the PICMG® CompactPCI® specifications. There are SATAIII, USB3.0, Gigabit Ethernet, and Keyboard/Mouse interfaces on the board. CP62007N supports 64GB SSD, facilitating the operating system installing.Part of CP62007N’s rear I/O uses high speed ZD connectors for transferring PCIe2.0, USB3.0, SATAIII and other high speed signals, leading to 2x 8 PCIe (to J3-J4) and a 1x 8 PCIe to XMC. All the PCIe is flexible configuration, for instance, a 2x 8 PCIe can be set into 2 x8, 1 x8 + 2 x4, or 4 x4.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PCIe-8361 , x1 Gen1 PCI Express Host, 208 MB/s, 1-Port, Copper Cable MXI-Express Device for PXI Remote Control
779504-01
The PCIe‑8361 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI Express slot. The PCIe‑8361 remote controller provides a x1 PCI Express link over a copper cable to the PXIe‑8360 remote control module when used for PXI system control. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
PCIe-4065, PCI Express, 6½-Digit, ±300 V Digital Multimeter Device
779771-01
The PCIe‑4065 makes AC/DC voltage, AC/DC current, and 2‑ or 4‑wire resistance measurements, as well as diode tests. It is ideally suited for OEMs, educational laboratories, or other cost-conscious test and measurement applications.
-
product
PCI High Density Potentiometer Card 9-Channel, 8-Bit, 0 To 255 Ohm
50-296A-121-9/8
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
DAQ Modules
Q.series X DAQ Modules for EtherCAT
All Q.series X DAQ systems possess the same measurement capabilities and performance. The main differentiating factor between the XL and XE versions of Q.series X is the Fieldbus communication protocol, which can be interchanged on Q.series X modules using a simple firmware update.
-
product
PCI High Density Potentiometer Card 1-Channel, 24-Bit, 0 To 16M Ohm
50-296A-021-1/24
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6778
The Technobox, Inc. P/N 6778 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
product
PCI Express Digital I/O Cards With Counters And COS Detection
PCIe-DIO-24DCS, PCIe-DIO-24DC, PCIe-DIO-24DS, and PCIe-DIO-24D,
This product is a x1 lane PCIe DIO board available in four models ranging from basic DIO to advanced COS detection and Counter/Timer capabilities. The card emulates an 8255 compatible chip, providing 24 DIO lines. The DIO lines are grouped into three 8-bit ports: A, B, and C. Each 8-bit port is configured via software to function as either inputs or outputs. Port C can be further broken into two 4-bit nybbles via software and configured as either inputs or outputs.
-
product
LGA 1151 Intel® Xeon® E3 v5/v6 & 6th/7th Generation Core™ ATX Server Board with 4 DDR4, 4 PCIe, 3 PCI, 6 USB 3.0, 6 COM, 6 SATA3, Quad/Dual LANs, IPMI
ASMB-785
- Supports LGA 1151 Intel® Xeon® E3-1200 v5/v6 and 6th/7th Generation Core™ i7/i5/i3 processors- DDR4 2400/2133/1866/1600/1333 MHz ECC/Non-ECC UDIMM up to 64 GB- One Gen 3.0 PCIe x16 link (or two PCIe x16 slots with x8 link), two PCIe x4, and three PCI slots- Triple display - two DVI-D and one VGA ports- Supports up to ten RS-232 or six RS-232 and four RS-422/485 ports- Rackmount optimized placement with positive air flow design- 0 ~ 60 °C ambient operation temperature range
-
product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 472Ω
50-297-120
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 11.4MΩ
50-297-153
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
2-slot Fanless Industrial System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® Q170, Front-access I/O, PCIe And PCI Slots
IPC962-512-FL
The IPC962-512-FL is powered by the 7th/6th generation Intel® Core™ and Celeron® processors (codename: Kaby Lake/Skylake) with the Intel® Q170 chipset. It is equipped with dual DDR4-2133 SO-DIMM slots with up to 32GB system memory. The ultra-compact industrial computer supports two swappable 2.5" HDDs; moreover, it offers flexible expansion options with one I/O module slot and two PCI/PCIe slots. It also has a wide operating temperature range of -10°C to +60°C and a 24VDC (uMin=19V / uMax=30V) power input for severe environments. According to the features above, this rugged IP40 industrial PC is a great choice for a wide variety of Industrial IoT applications including automatic optical inspection, digital signage, motion control, and factory automation.
-
product
PCI Dual Channel Multi-Band Down Converter
LS-27-D
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
product
Squid Carrier Board™ Family PCI Express Gen 2 Carrier Board for 4 PCIe M.2 SSD Modules
SKU-086-01
The Squid PCI Express Carrier board for M.2 SSD modules is the second product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 4 M.2 PCI Express SSD modules. This product is recommended for use in Mac Pro Desktop computers.
-
product
PCI Mezzanine Card
PNIC1G
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
