Programmable Oscillators
-
product
Oscillators
TCXO
A crystal oscillator specially designed to operate in high-temperature environments.
-
product
Programmable Linear DC Power Supply, 3 Output, 0-32V/0-3.2A, 2.5V/3.3V/5V/3.2A
T3PS3000
Teledyne Test Tools new T3PS3000 is a Linear Programmable DC Power Supply with a 4.3 inch TFT LCD display. It has three isolated outputs: two adjustable channels and one selectable channel from 2.5 V, 3.3 V, and 5 V with output short and overload protection for each channel. Support for series and parallel operation of the two main channels extends its flexibility beyond the standard specification. The T3PS3000 features include programmability via USB or LAN, a graphical display of power waveforms, and the high resolution numeric display of voltage and current. Typical users are Education, Production, and Design and Development.
-
product
Oven Controlled Crystal Oscillators
OCXOS
Oven Controlled Crystal Oscillators (OCXOs) deliver the ultimate piezo electric performance with stabilities down to less than ±1ppb. An OCXO offers frequency stabilities even tighter than those offered by a TCXO.
-
product
Programmable Benchtop DC Power Supply
62000L
Chroma Systems Solutions, Inc.
Provides high quality yet cost effective programmable benchtop DC power, designed to meet the stringent requirements of the next generation of power electronics.
-
product
Linear Power Supplies Programmable, Digital Control, Rack Mount, Ultra Low Ripple/Noise
Series MAT
Kepco MAT are linear power supplies that are oriented to systems applications. Their principal control means is a 2-wire, long range, serial bus, Kepco's single address, multiple instrument bus. As many as 27 power supplies, including models in the Kepco MST, MBT and BOP series may be "daisy-chained" on this bus and interfaced either to IEEE 488.2, a PC bus, or to a VXI host.
-
product
Voltage Controlled Oscillators
World's widest selectionWideband up to full octaveLinear tuning
-
product
PCI Precision Resistor Card 9-Channel
50-297-030
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
USB Programmable SPDT and SP4T Solid State RF and Microwave Switches
LSW Series
The Lab Brick LSW Series RF and Microwave Switch product family offers reliable, high isolation and low cost solid state switch products in both single pole double throw and single pole four throw configurations. These units require connection to a USB port for control and power. No additional DC supply voltage is required. Lab Brick RF and Microwave Switches are easily controlled and programmed directly from the included GUI and through the external control inputs. Lab Brick Switch API DLL and LabVIEW compatible drivers are also available for custom programming applications.
-
product
Programmable Serial Device
HR-16P
The HR-16P is a programmable RS-232 serial device designed to control any device with a serial port based on sensing level changes (open-to-close and close-to-open, or digital high to low and vice versa).
-
product
Multicoupler, Rack Mount, 1U, Switchable Dual 2×4/1×8, P, LL/UL/S/C, Programmable Amplitude Balance
LS-16A-R1-24SPLUSC
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
product
PCI Precision Resistor Card 9-Channel, 2Ω To 13.6kΩ
50-297-031
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
USB/RS232/SPI Programmable Attenuator
RUDAT-13G-90
Mini-Circuits’ RUDAT-13G-90 is a general purpose programmable RF attenuator supporting frequencies from 10 to 13000 MHz with attenuation from 0 to 90 dB in 0.5 dB steps. Its unique design maintains linear attenuation change per dB, even at the highest attenuation and frequency settings. The attenuator is controlled via USB, RS232 or SPI. It comes housed in a compact, shielded metal case with SMA(F) input/ output RF ports (RF ports are interchangeable), a USB type Mini-B socket, and a 9-pin D-sub(F) RS232 and SPI port. Power can be supplied via either USB or the D-sub port. The RUDAT-13G-90 is supplied with our easy-to-install, user-friendly GUI software, API objects for Windows® environments, and complete programming instructions for 32 and 64 bit Windows® and Linux® operating systems. See p. 9 for a complete list of included accessories.
-
product
Programmable Linear Dc Power Supply
DP700 Series
DP700 is a basic power supply product designed for users with lower cost and smaller size and high reliability. It has low ripple noise, fast transient response, excellent power supply and load regulation rate, powerful timing output function and complete protection function.
-
product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 60 V, 0 A, 3 A
72-2720
The 72-2720 from Tenma is a single channel programmable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +30mV (voltage), ≤0.5% +10mA (current).
-
product
100 High Speed Programmer
Commander Accelerator
The Commander High Speed Programmer (HSP) is low overhead system designed to test Flash Memories, PLA's and Micro-controllers. The parallel multi-module architecture provides the flexibility to program and test multiple devices. It's full-featured capabilities support chip erasing and programming, sector erasing and programming, sector protect and unprotect, and data verification functions.
-
product
TINYig Oscillators
The smallest available oscillator in the industry, Teledyne Microwave's TINYIG is an ultra-low phase noise YIG-tuned oscillator (YTO) that provides superior phase noise frequency up to 20 GHz. Uniquely designed to be RoHS compliant, these YIG TO-8 oscillators exploit the principle of magnetic resonance to generate a clean, low phase noise microwave signal over broad tuning ranges. It can greatly simplify system designs, thus reducing costs, eliminating the need for extra components, and reducing the risk of malfunctions of complicated electronic connections and operations.
-
product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 32.7k Ohm - SPST
40-294-132
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
RoHS Compliant, Automatic Crossover, Low-Profile, Programmable Power Supplies
Series KLN
The KLN Series offers stable d-c power in:1U high, half-rack package for 750W,1U high, full-rack package for 1,500W2U high, full-rack package for 3,000W.
-
product
UNA Programmer
MS 1604
The UNA programmer is used to program the UNA board. The UNA Programmer is a processor-based system. The UNA Programmer performs the Blank checking, Programming, Reading and Verification
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-033
The 40-297A-033 (PXI) and the 42-297A-033 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 52.4 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 127 Ohm - SPST
50-294-112
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
AC Programmable Hipot Tester
Shenzhen Chuangxin Instruments Co., Ltd.
AC Programmable Hipot Tester
-
product
PXI Potentiometer Module 2x16 Bit, 0 Ohm to 65K Ohm
40-296-021-2/16
The 40-295 is a Programmable Resistor module with up to 18 channels of 8-bit resolution resistor chains in a single 3U PXI module. The flexible architecture allows these modules to also be supplied as 12, 16 or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count.
-
product
Programmable Power Modules
Series MST
MST power modules are a group of programmable power supplies that are compatible with Kepco¹s single address, multiple instrument serial control bus. The MST provide precision interactive control in the 200 Watt power class. The housings for MST, either RA 55 or CA400, each contain a slot to accommodate an IEEE 488.2 adapter. If not used, an additional MST power module may be plugged into that slot.
-
product
Programmable Step Attenuator, DC to 50 GHz, 0 to 11 dB, 1 dB Steps
84904M
Keysight now offers a family of higher frequency attenuators for your communications and aerospace applications. Combining low insertion loss with long life and excellent repeatability, these attenuators safeguard your test platform from failures, recalibration, downtime, and lost production.
-
product
Precision Programmable Regenerative Grid Simulator, 0 - 333VAC, 0 - 3,000A / Phase, 15kVA - 1.08MVA
Sequoia Series
AMETEK Programmable Power, Inc.
The California Instruments Sequoia Series combines intelligence and flexibility with high power to create an advanced platform of AC solutions. Using a state-of the-art SiC power switching architecture, this full four quadrant product combines compactness, robustness, and functionality in a floor-standing chassis.
-
product
AC to DC Programmable Power Sources
CEHCO can supply AC to DC Programmable Power Sources. We offer standard or customized solutions. The ADG-L Series is up to 1000 VDC maximum output. ADG-P Series is up to 2000 VDC maximum output.
-
product
Programmable DC Electronic Load
63000 Series
The 63000 Series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power suppl ies, A/D power suppl ies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices. The 63000 Series offers models in two operating voltages 150V models, with 250W and 350W power levels up to 60A in a single unit. Their compact and light weight design make these loads easy to move around which is ideal for R&D and design validation. Each model of the 63000 Series has unique user-def ined waveform (UDW) funct ion capable of simulating real-world custom waveforms. In addition, a data storage function has been built in for saving and recalling up to 100 stored settings at any time. For automated testing, these save and recall functions can save a great deal of time. The 63000 Series has 3 power ranges that can precisely measure the voltage and current in real time. Since short circuit testing is a critical test item, the 63000 provides short circuit simulation to effectively address application demands for power and automated testing.
-
product
Isolated Programmable Multifunction Counter Board
APCI-1710-24V
Wide application possibilities through free combination4 modules with numerous functions quickly and easily programmableEach of the 4 modules is programmed with a function. The 4 modules can either be programmed with the same function or freely be combined with 4 different functions.
-
product
ISP Programmer Superpro Is01
Features:Until now,Support IC manufacturer, pcs devices and keeps growing.1)High speed thanks to the flexible hardware engine. Programming speed adjustable for complicated application environments brought by user target board, length of ISP cable etc.2)Stand-alone and PC-Hosted (USB2.0 High Speed) dual mode;3)Supports ISP programming of devices with I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 and any other serial port.4)ATE interface;5)Over-current and ESD protection to protect your equipment;6)DLL and API for easy integration into customers’ system.Hardware Specifications:1) ISP cable integrates I2C, SPI, UART, BDM, MON, MW, JTAG, CAN, ICC, RS232 interfaces。2) VDD (0-5.5V /0.5A) and Vpp (0-15V / 0.2A) lines provided to power the target board and the target devices.3) Cable driver circuit supports target devices of voltage level 1.5-5V and is ESD protected.4) USB 2.0 (high speed) interface for PC hosted mode and management of project files on SD card.5) A 20 Characters x 4 lines LCD and a 6-key keypad are built with it for stand-alone operation. In stand-alone mode project files are stored on the SD card (up to 16GB). The number of the project files is limited only by the capacity of the SD card.6) ATE interface is built for easy external hardware control. 6 lines SEL0-SEL5 are for project selection (maximum 64 files); 2 command lines START and STOP; 3 STATUS lines PASS, FAIL and BUSY. All signals are optical-isolated.7) A universal AC adaptor of DC12V/2A is included for power supply.8)WINDOWS XP/Vista/Win7/Win8/Win10 32/64bit compatibility.Software Specifications:1) Supports almost all devices with ISP interface.2) Supports Jam and Staple files from ACTEL and ALTERA; Direct C files from ACTEL.3) Programming speed selectable (High, Normal and Low) for complicated applications such as different cable lengths, different target load characters.4) Dynamic buffer function. Application examples include device S/N, MAC address, frequency or transducer calibration etc.5) File format on SD: FAT16, FAT32.6) Functions for IP protection: Project security, SD security, batch control, administration management etc. 7) API and DLL provided for easy integration into customers’ system like ICT and ATE.8) Software provides the features for multiple units to work concurrently controlled by USB HUB.Applications:1)R&D application like in-circuit test and debug.2)Volume production. Devices may be programmed after the board is fully assembled. One example is the serial number writing to an on-board serial device.3)Field application. Comes with portability, stand-alone mode and mobile data storage media (SD card), it is suitable for field test, debug and data acquisition.4)Third application modules. Friend s/w interface (DLL and Virtual Com communication command set) and h/w interface ( ATE and USB) are provided and make it very easy for customers to integrate ISP01 as a functional module into their systems. One example is the ICT equipment. With this integration user can finish in-circuit test and in-circuit programming in one step.
