Debugging
fixes identified bugs.
See Also: Debuggers, In-Circuit Debuggers, Code Debuggers, JTAG Debuggers, Source Debugers
-
Product
Debug probe for ARM Cortex processors
USB Multilink ACP
-
P&E’s USB Multilink ACP is a debug probe which allows a PC/laptop access to JTAG/SWD on ARM Cortex devices from several manufacturers (see complete list below). It connects between a USB port on a Windows machine and the standard debug connector on the target. The product photos to the left of this page show how the headers can be accessed by simply flipping open the plastic case. Ribbon cables suitable for a variety of architectures are included. By using the USB Multilink ACP, the user can take advantage of the debug mode to halt normal processor execution and use a PC to control the processor. The user can then directly control the target’s execution, read/write registers and memory values, debug code on the processor, and program internal or external FLASH memory devices.
-
Product
Wireless Functional Test Fixtures
-
Circuit Check’s wireless fixture technologies reduce debug time, simplify ECO’s and reduce maintenance. This allows for the highest test performance, ability to probe denser smaller targets and achieve ultra-high node counts. Higher density more complex circuit boards complicate testing requirements. Smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board (T-Board).
-
Product
Bus Analyzer
Scribe I2C
-
The Blackhawk Scribe is an entry level, yet feature-packed and robust I2C debugging tool. The Scribe was designed to help engineers developing products which utilize the IC and SMBus interfaces.
-
Product
RF Test Spectrum Measurements over CPRI
Integris 3000
-
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
Product
Pocket-Sized Analyzer for Capturing & Decoding USB 2.0 Devices
Mercury T2C / T2P
Analyzer
The pocket-sized Mercury T2C & T2P capture and decode the widest range of USB 2.0 device classes plus Type-C link states and Power Delivery 3.0 messages. Both the Mercury T2C and T2P utilize the industry leading CATC Trace analysis software for verifying and debugging USB and PD protocol issues. Now there are two base models to choose from; the original Mercury T2C and the new Mercury T2P, which adds the Power Tracker graphical view of VBUS and CC voltages.
-
Product
Software Abstraction for Easy Control of DC Power Supplies
Konrad DCPower
-
It consists of three modules:- A windows driver which is responsible for the communication and device abstraction- A DLL with NI TestStand Test Steps which allows easy integration in automated production environments- A standalone executable which simplifies debugging and setup of test sequencesThis architecture allows to open a communication channel from multiple instances to the same device. This is important when for example two channels of a power supply are used in two independent applications.
-
Product
LPDDR3 178-ball BGA Interposer For Logic Analyzers
W3301A
Interposer
The W3301A LPDDR3 rigid BGA interposer for LPDDR3 178-ball DRAM enables capture of simultaneous read and write traffic at data rates in excess of 1866 Mb/s. E5406A Soft Touch probes and U4201A cables connect the W3301A LPDDR3 BGA interposer into the U4164A logic analyzer module. The W3301A LPDDR3 178-ball rigid BGA interposer allows signal access to the LPDDR3 signals critical to your debug and validation effort through a U4164A logic analyzer. The probe works in existing designs and eliminates the need for up-front planning or redesign. The probe connects directly to the balls of the DRAM using a LPDDR3 178-ball riser (included) or an optional 3rd party socket (not provided), enabling operation and acquisition of LPDDR3 signals.
-
Product
9 Pin Breakout Interface
VSI-Breakout-9
-
The VSI-Breakout-9 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
Protocol Analyzer
CY4500 EZ-PD
-
The CY4500 EZ-PD Protocol Analyzer records traffic passively on the Configuration Channel (CC) and allows users to analyze and debug USB Power Delivery communication. The low-cost and compact CY4500 acts as a pass-through for VBUS, VCONN, USB 3.1, USB 2.0 and USB-PD traffic. The EZ-PD Protocol Analyzer Installer includes a free Windows-based GUI (EZ-PD Analyzer Utility) that can be used to decode the USB-PD messages.
-
Product
Logic Analyzer
FS2352B
-
The FS2352B is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s Logic Analyzer modules, it gives the user an effective tool for debugging, testing and verifying DDR3 DIMMs. This logic analyzer probe has a CKE qualification circuit that allows for the use of older Keysight logic analysis modules when testing systems using power saving modes.
-
Product
Test Development Solution
-
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete "turn-key" service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
RTL debugger and viewer for Verilog and VHDL
RTLvision
-
RTLvision PRO provides easy RTL debugging and fast visualization of RTL code, so that engineers can easily understand, implement and optimize VHDL, Verilog or SystemVerilog code. Please check out the Demo Videos: Basic Features and Clock Tree Analyzer.
-
Product
RF Amplifier
SA1001H
-
Hangzhou Softel Optic Co., Ltd.
*SA1001H Indoor Bi-directional Amplifier are special amplifiers designed for the last”1km” of the bi-directional transmission network.. Special CATV RF modules packaged in SOT-115 are used as forward channel; Microwave tube push-pull circuit with low noise are used as backward channel ;It has the characteristics of low power consumption，high reliability and excellent cost performance. And it is suitable for small and medium sized CATV bi-directional transmission network*It is more convenient for debug engineering debug, because of the plug-in diplexer filters with built-in adjustable equalizers, adjustable attenuators, plug-in output splitters and scientific and reasonable ports for online test.*These equipments will work in the field rugged environment for a long time continuously, because of the aluminium alloy casing, good heat dispersing performances, beautiful looks, dependable linear power supply and lightning protection systems.
-
Product
Wireless In-Circuit Test Fixtures
-
Higher density more complex circuit boards complicate testing requirements while smaller more tightly spaced test pads create a wiring challenge for the fixture fabricators, test engineers and maintenance personnel. Wireless fixtures solve the challenges associated with the nest of wires found in standard long wire fixtures. Wireless fixtures replace the “nest” of wires with copper traces on a multilayered printed circuit board called a Translator Board or T-Board®. Circuit Check’s wireless fixture technologies reduce test program debug and maintenance times while easing the ECO process. Thus allowing for the higher level of test performance, the ability to probe smaller denser targets and achieve ultra-high node counts.
-
Product
Digital Pattern Generators
DPG
-
Active Technologies Digital Pattern Generators also known as DPG, allow digital stimuli generation to stimulate digital designs, providing the capability to emulate standard serial or parallel bus transactions or custom digital interfaces, for system or device debugging and characterization.
-
Product
ATE Test & Engineering Services
-
We can provide a limited scope project or a full turn key solution where we analyze a data sheet and provide a full test plan. Our wide range of ATE test equipment and experienced team can support first silicon debug to release to high volume production for a wide range of products, from Digital to RF, including wafer sort and packaged part testing. Test platforms include Verigy, Teradyne, Advantest.
-
Product
Kernel Aware Debug
-
Kernel Awareness for RTXC Quadros gives the developer deep visibility into virtually every aspect of kernel activity during debugging. The popup windows allow you to view RTXC Quadros-specific objects in an easy-to-read fashion.
-
Product
FPGA Dynamic Probe for Xilinx FPGA
B4655A
-
Quickly access internal Xilinx FPGA signals Make incremental measurements in seconds, without changing design timing Access up to 128 internal Xilinx FPGA signals for each pin dedicated to debug Measurement can be either in State (synchronous) or timing (asynchronous) mode
-
Product
PCIe Smart Bus Extenders
PCIeEXT-16HOT - PCIe LIVE INSERTION EXTENDER
-
The PCIeEXT16HOT enables PCIe x16/x8/x4/x2/x1 boards to be rapidly tested, removed and swapped without having to reboot or power down the host system. Enabling rapid production testing and engineering debug, the hot insertion, current reporting, overcurrent indication and limiting and voltage margining capabilities make this board the highest performance PCIe bus extender in the industry.
-
Product
15 Pin Breakout Interface
VSI-Breakout-15
-
The VSI-Breakout-15 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
IDE, Compiler And Debugger
RiscFree™ SDK
-
RiscFree is Ashling’s cross platform SDK including an IDE and Debugger, Integrated Compiler Toolchain, Project Manager and Build System, Single-shot Installer and Source-code Creation and Navigation. The integrated Debugger provides full Multi-core Homogeneous and Heterogeneous Support including debug and trace support via the Ashling Probes for RISC-V, Arm, ARC, ARC-V and MIPS based cores
-
Product
Program Development for Multisite Test
IG-XL
-
Teradyne’s award winning IG-XL software transforms test program development for the FLEX, UltraFLEX and J750 family of testers. Its powerful, yet easy-to-use, graphical environment lets engineers rapidly develop fully functional test programs, cutting program development and debugging time. Designed to address multisite complexity, IG-XL can convert single site test programs to multisite automatically, speeding time to market and reducing cost of test. With IG-XL, test engineers focus on actual testing, not writing code for the tester.
-
Product
PCI Smart Bus Extenders
PCIEXT-64 - Live Insertion PCI Bus Extender
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment.
-
Product
NightStar Tools
-
Debugging and analysis tools that reduce test time, increase productivity and lower development costs.
-
Product
Framework for Soft-Error Protection
RobustScan™
-
RobustScan™ provides a platform for users to pick patented Configurable Soft-Error Resilience (CSER) cells or their preferred SER mitigation cells. First, Soft-Error Rate (SER) analysis is performed. Then it performs automatic robust-scan-cell and hardenedcombinational- cell selection and synthesis. Finally it generates verification testbenches for the final design. RobustScan™ can be used with scan chains inserted using third-party tools; it can be linked to third-party�s SER analysis programs and is fully compatible with SynTest�s existing DFT tools for test, debug, and diagnosis.
-
Product
PCI To PC104 Extender Board
MS 1717
-
PCI to PC104/EPIC Extender card is used for extending the standard desktop PCI bus to compatible PC104 or EPIC bus. This will help to test all the PC104 cards through standard PC without any embedded processors. This card is very low cost board and very use to interface with standard board. This board also facilitates to debug the PC104 or EPIC boards.
-
Product
PCI-X Carrier For AMC Modules
PCI102
-
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
Product
System Trace Emulators
XDS560v2
-
The XDS560v2 System Trace Emulator is the second generation of the XDS560-class emulator design from Texas Instruments. It provides cost effective real-time emulation, debugging, and high-performance System Trace (STM) for Texas Instruments devices over both USB and Ethernet PC interfaces.
-
Product
VME Test Extender 3U/220mm Universal
110EXT3122-10xx
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Quickly Upgrade RF ATE Testers
MP5800 / MP5806
-
*MP5800 Quickly Provides 3380 / 3650 RF ATE Test Capabilities*MP5800 and 3380/3650 hardware and software are fully integrated*Provide complete and user-friendly RF / Digital debug tools*Provide a complete solution for IOT applications*Provide API for production automation software*Integrate Zimmer 3380/3650 to provide RF/Digital comprehensive ATE test solution
