Debugging
fixes identified bugs.
See Also: Debuggers, In-Circuit Debuggers, Code Debuggers, JTAG Debuggers, Source Debugers
-
Product
Embedded Engineer
-
Embedded Engineer combines automated source code generation with model-level debugging. The plug-and-play product provides optimized generation of ANSI C code from UML structures, state machines and activity models as well as the generation of C ++ source code. Embedded Engineer also guarantees the traceability of requirements to the code and back again.
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Extender Boards
-
VECTOR Electronics and Technology, Inc.
Extender boards are designed to bring a circuit card completely out of a card cage or enclosure so that it can be tested or debugged. This provides access to both sides of the test board.
-
Product
PathWave Waveform Analytics Software
-
Debug voltage and current spikes, IO glitches, and time shifts in pre-silicon using powerful machine learning.
-
Product
Build FPGA-based Processor Systems In Minutes
Lattice Propel Design Environment
-
Design Environment for Lattice FPGA-based Processor System Design - Lattice Propel is a complete set of graphical and command-line tools to create, analyze, compile, and debug both the hardware design of an FPGA-based processor system, and the software design for that processor system.
-
Product
RF Test Spectrum Measurements over CPRI
Integris 3000
-
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
Product
Test Development Solution
-
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete "turn-key" service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
cRIO-9042, 1.60 GHz Quad-Core CPU, 4 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
785622-01
Controller
1.60 GHz Quad-Core CPU, 4 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9042 is a rugged, high-performance, customizable embedded controller that offers Intel Atom quad-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
PCI Express Gen 3 Test Backplane
SKU-015-01-PCIe
-
PCI Express Backplane was designed to support a variety of modern PCI Express board’s production testing and debugging. The backplane expands the Host computer into four x16 PCI Express slots via 10 ft. CAT7 data and 10-pin flat Power control cables. PCI Express Backplane and UUTs (unit under test – add-in PCI Express board) are powered by a standard ATX power supply connected to the backplane via 24 and 8 pin power connectors located on the backplane.
-
Product
High-Performance Intelligent Pod for Corelis Boundary-Scan Controllers
ScanTAP 4 & 8
-
Boundary-scan has proven itself time and again to be a truly versatile interface for structural test, embedded functional test, built-in self-test (BIST), software debug, and in-system programming. Supporting such diverse applications requires equipment with high-performance specifications and extended features.Corelis ScanTAP pods are designed for use with PCI-1149.1/Turbo and PCIe-1149.1 high-speed JTAG controllers. Featuring 4 & 8 independent Test Access Ports (TAPs), up to 80 MHz clock rates, and advanced TAP capabilities such as analog voltage measurement, the ScanTAP family of intelligent pods is the ideal JTAG interface for high-performance environments.
-
Product
Training Services
-
Austin Labs offers a full line of advanced protocol training classes. All classes are instructor led and guide students through the protocol specifications while using hands on labs with trace analysis to help students discover how the protocol is implemented. To create a reliable product, the user must first understand the technology and know how to use the tools needed to develop, test and debug the relevant host or peripheral specification. Here at Austin Labs we provide everything you need.
-
Product
Logic Analyzer Module With State Mode Up To 4Gb/s
U4164A
Logic Analyzer
The U4164A logic analyzer provides industry’s highest data rate state mode (up to 4 Gb/s), highest deep trace timing mode (up to 10 GHz), and deepest memory (up to 400 Mb), enabling validation and debug of DDR4 or LPDDR4 at data rates over 3.5 Gb/s.
-
Product
VirtualBench All-in-One Instrument
-
The VirtualBench All-in-One Instrument combines a mixed-signal oscilloscope with protocol analysis, an arbitrary waveform generator, a digital multimeter, a programmable DC power supply, and digital I/O. The all-in-one features are simple, convenient, and provide more efficient circuit design, debugging, and validation. The included software lets you view all measurements on a single screen and can be updated with free software releases to add functionality and value. The VirtualBench All-in-One Instrument easily integrates with LabVIEW software to provide programmatic control and automated test sequences.
-
Product
Test & Measurement Platform
Konrad System Manager
-
The Konrad System Manager is the central tool for the Konrad test and measurement platform. It combines execution, interactive supervision and documentation of the installed Konrad test modules.- Displays the live status of the module functions in parallel to running test executions- Easy debugging of the switch routes- Control the modules functions- Configure device Alias name for modules- Display alias naming for switching channels- Execute selftest functionality of the modules- Display device information and documentation of the installed modules- Simulate modules
-
Product
Coaxial Cable Termination Toolkit
ICFP
-
Ardent’s ICFP is a next generation coaxial cable termination toolkit for advanced system design de-embedding, de-bugging, and calibration. Designed for the lowest loss access to signal paths on an IC circuit footprint, this solution is a simple, cost effective alternative to expensive probers and x-y tables for Engineers who need to probe multiple signals at once.
-
Product
Catena 1910 HSIC Tester
Catena 1910
-
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
Product
In-Circuit Debugger for ColdFire V1
ICDCFV1
-
P&E's ICDCFV1 is a powerful tool for debugging code that supports Freescale's ColdFire V1 microcontrollers.
-
Product
16 Channels, 200MHz, 1 M Samples/Channel Buffer USB Logic Analyzer
La-Logic-16
-
The La-Logic-16 is a sophisticated PC-based logic analyzer. It captures at a maximum of 200Mhz on its 16 channels simultaneously into it?s deep 1M samples/channel buffer.It can also operate as a 16-channel pattern generator.It connects to the PC via the USB-port and does not require any external power. The package is complete with all accessories included to start debugging immediately.
-
Product
ICT Software: Interactive Developmetn Encironment ICT ICE & ICT Sequencer
ICT IDE and Sequencer
-
The ICT software consists of two parts, the interactive development environment ICT IDE and the ICT sequencer. The IDE provides a graphical user interface for convenient creation and testing of these test sequences and allows:- Convenient management of hardware resources via topology editor- Support of several independent embedded testers for parallel test execution- Editing sequences in a text or table editor- Error highlighting during sequencing- Sequence execution (also single step) directly on a selected DUT- Debugging (single step)- Loop execution via sequences, or single steps- Optimization function with regard to waiting time and integration with Shmoo plot- detailed results output within tables as well as various results diagrams- Pin-Finder function to support adapter wiring- Automatic test program generation is available via Aster Testway
-
Product
Multi-Layer Analyzers
DSL Xpert™
-
The patent-pending DSL Xpert multi-layer analyzer broke new ground as the only non-intrusive performance analysis solution for ADSL2Plus, ADSL2 and ADSL products. It is a modular tool designed for R&D and laboratory engineers engaged in the deployment of ADSL2Plus, ADSL2 and ADSL standard-compliant solutions. Cutting significant time from ADSL development, deployment, debugging and interoperability verification, DSL Xpert� accelerates time to market and return on investment.
-
Product
LXI Matrix Switching Unit
ProDAQ 6140
-
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
Product
37 Pin Breakout Interface
VSI-Breakout-37
-
The VSI-Breakout-37 is a very useful tool in debugging signals or software in a system. It allows unlimited access to signals within the cabling that might otherwise be difficult to access. The board gives test points at each side of the connector and jumper with a easy to use tabbed shunt to allow for easy disconnection of any particular signal between the connectors. The jumpers also give an opportunity to inject a signal regardless of what signal was originally being driven.
-
Product
cRIO-9040, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller
785624-01
Embedded Controller
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -20 °C to 55 °C, Kintex-7 70T FPGA, 4-Slot CompactRIO Controller - The cRIO-9040 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for … data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
Product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-02
Interface Module
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
Product
CASS Instrument Real Time Controller
-
External control of the Navy CASS ATE via Ethernet. Standardized graphical user interface (GUI) for individual control of each instrument independent of CASS software. Allows TPS developer or ATE maintainer to change/control instrument settings for TPS debug and instrument troubleshooting.
-
Product
PCI Express 5 CEM Receiver Test Automation
N5991PC5A
-
The N5991PC5A is the receiver test automation software for bit error ratio testers, allowing you to test, debug and characterize PCI Express 5.0 CEM Add-In Cards and systems.
-
Product
Emulator
-
Is an advanced on-chip debugging emulator and flash programmer developed with the concept of greater efficiency in development. The combination of its high-speed downloading and various software and hardware solutions will contribute to reducing development times.
-
Product
LPDDR5 Protocol Debug And Analysis Solution
U4971A
-
The LPDDR5 Solution Bundle provides a systemized hardware, probing, and software solution for LPDDR / 2 / 3 / 4 / 5 protocol debug, compliance validation, and analysis.
-
Product
Pocket-Sized Analyzer for Capturing & Decoding USB 2.0 Devices
Mercury T2C / T2P
Analyzer
The pocket-sized Mercury T2C & T2P capture and decode the widest range of USB 2.0 device classes plus Type-C link states and Power Delivery 3.0 messages. Both the Mercury T2C and T2P utilize the industry leading CATC Trace analysis software for verifying and debugging USB and PD protocol issues. Now there are two base models to choose from; the original Mercury T2C and the new Mercury T2P, which adds the Power Tracker graphical view of VBUS and CC voltages.
-
Product
Bus Analyzer, Monitor, Debugger & Programmer
BusPro-I™
-
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
