Filter Results By:
Products
Applications
Manufacturers
-
product
Data Acquisition Systems
xDAP
The new xDAP line of Data Acquisition Processor systems combines a high performance analog interface with a speed-optimized USB host connection. This combination allows you to build uncompromising data acquisition systems with a laptop, or any other USB connected Windows PC.
-
product
MXI-Express Cable, Gen 2 x8, Copper, 3m
782317-03
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
product
PCI-8366, PCI Host, 100 MB/s, Fiber-Optic Cable MXI-Express Device for PXI Remote Control
781400-01
The PCI‑8366 is an MXI‑Express remote controller for devices or systems over cabled PCI from a computer with a PCI slot. The PCI‑8366 remote controller provides a PCI link over a fiber-optic cable to the PXI‑8368 remote control module when used for PXI system control. Fiber-optic remote control solutions are ideal for long‑distance‑device control and electrical isolation. This link is transparent to software applications and drivers, so computers and servers can control connected devices with no additional programming. With NI remote controllers, PXI modules can be used as if they are PCI devices directly installed in the computer.
-
product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB110
The FAB110 offers one PCIe x16 slot, one PCIe x4 slots and two 32bit/33MHz PCI slots as well as the PICMG 1.3 slot for the SHB (system host board). The onboard 24-pi ATX power connector and 8-pin connector for thermal detected board are featured. Furthermore, the backplane supports two high speed USB 2.0 ports. The FAB110 is designed for the 6-slot industrial chassis, such as Axiomtek's AX60501 and AX6052.
-
product
Ultra-High Vacuum Scanning Kelvin Probe
Our Ultra-high Vacuum Scanning Kelvin Probes (UHVSKP2020 and UHVSKP5050) give the user full access to work function (Φ) and contact potential difference (CPD) measurements under vacuum with the ability to scan a sample area of 20 x 20mm or 50 x 50mm respectively. Each system comes with the UHV head unit, tip amplifier (located at the mounting port), digital control unit and host PC with dedicated software. The tip can be retracted 100mm from the sample and approaches normal to the sample. The associated digital electronic unit powers the head unit and provides an interface between the head unit and the data acquisition system. The system comes with a complete user manual, which includes an introduction to work function measurements and a detailed description of the system software, including examples. The work function resolution of the Ultra-High Vacuum Scanning Kelvin Probes is 1-3 meV.
-
product
Cable Working Equipment Products
DLM’s long involvement operating in and supplying to the Cable Laying Industry has led to the development of a multitude of products to support operations. From a host of Grapnels for PLGR operations, Saddleback Monitors to measure cable Tension right through to rigging and deck equipment.
-
product
USB Cable
143556-01
USB Cable - The USB Cable works with SuperSpeed or Hi-Speed USB hosts and devices but is backward-compatible with USB 1.1 hosts and devices. You can use this cable for vision acquisition hardware, CompactDAQ or CompactRIO systems, or any device that supports USB Cables.
-
product
PCI Express To CPCI Board
MS 1719
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
Broadband Switches
Maxim's broadband switch portfolio offers protocol-specific solutions for high-speed (> 500MHz) interfaces. These devices are bidirectional, passive switches that allow the customer to switch between multiple hosts and downstream ports. Because the high-speed switches are protocol-specific for USB 3.0, VGA, DisplayPort, SAS, and SATA interfaces, customers enjoy fully integrated, flexible, and easy to design solutions.
-
product
Wide Temperature Range HDR USB3.1 Gen1 Camera Board (Color)
See3CAM_CU20
See3CAM_CU20 is a 2.0 MP HDR USB camera board with ultra-Lowlight performance. It has an ability to stream seamlessly at wide temperature range (-40°C to 85°C). This Full HD USB3.1 Gen1(5Gb/Sec.) camera is based on 1/2.7" AR0230AT CMOS digital image sensor with a pixel size of 3.0 μm x 3.0 μm from ON Semiconductor™. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows, Linux. This HDR camera is also backward compatible with USB 2.0 host ports.
-
product
Microprocessor Development System
DS-85
* Real-Time and Transparent In-Circuit Emulator * Windows Debugger - Update 2009 * Symbolic Debugger compatible with Intel Object Files * 64K Hardware Breakpoints * 64K of Internal Memory * 32K x 32 Bit Trace Memory and Logic Analyzer with External Probes * Serially linked to IBM PC or Compatible Hosts * On-line Assembler and Disassembler * Source and Listing Windows
-
product
MXI-Express Cable, Gen 1 x1, Copper, 3m
779500-03
MXI-Express Cable with Communication Levels up to Gen 3 x8 - The MXI-Express Cable connects a host interface to a PXI or PXI Express chassis. You can also use it for data communication between multichassis systems. NI offers it in different MXI communication levels and lengths.
-
product
Enhanced Serial Interface Module for the Multiprotocol Excalibur 4000 Family of Carrier Boards
M4KSerialPlus
The M4KSerialPlus is an enhanced serial interface module for the multiprotocol Excalibur 4000 family of carrier boards, that includes several advanced features such as a high baud rate and high throughput. This module supports up to four independent channels of serial communications, each of which can be selected as RS-485, RS-422 or RS-232. The module operates independently of the host computer, reducing the need for host intervention.The M4KSerialPlus module is based on the Exar XR16M570 Universal Asynchronous Receiver/Transmitter (UART). The device is compatible to industry standard 16550 UARTs. Each of the M4KSerialPlus’s four channels contains a transmit FIFO capable of holding up to 16384 bytes and a receive FIFO capable of holding either 16384 receive bytes or 5460 bytes with a 32-bit Time Tag associated with each byte. These large buffers allow application code to transfer large quantities of data with a single non-blocking subroutine call. The 32-bit Time Tag on receive channels is very useful for synchronizing serial data with data from other modules on the 4000 board or on other interface boards. Each channel has a programmable baud rate of up to 10 Mbps and can be configured as RS-232, RS-422 or RS-485.The M4KSerialPlus module is supplied with C drivers, including source code.
-
product
SpaceWire-USB Brick Mk3
326
The SpaceWire Brick Mk3 is a USB 3.0 (also works with USB 2.0 and USB 1.1) to SpaceWire interface device that is suitable for use in all stages of SpaceWire equipment development: initial SpaceWire evaluation, instrument simulation, control system simulation, unit testing, integration support, and EGSE. The SpaceWire Brick Mk3 provides two SpaceWire interfaces, support for high speed data transfer, the capability to inject various types of errors on demand, the ability to transmit and receive time-codes and act as a time-code master, and comes complete with highly optimised host software for low latency transmission of SpaceWire packets directly to and from the host PC.
-
product
2-channel RF Transceiver Module
FMC30RF
Sundance Multiprocessor Technology Ltd.
The FMC30RF is an FMC Daughter Card which is fully compliant with the VITA 57.1-2010 standard. The FMC30RF offers in a small footprint a low power and fully featured Rx / Tx signal path for the development and deployment of advanced RF solutions. With a frequency range coverage from 400MHz to 3.0GHz* and up to 60MHz* bandwidth the FMC30RF provides flexibility and reconfigurability to a host of applications.
-
product
Multi-Interface Frame Grabber
Xtium2 CXP PX8 Series
The Xtium2™-CXP PX8 series is based on the industry standard PCI Express™ Gen 3.0 and CoaXPress ver 2.0 to transfers image data to the host memory at maximum acquisition rates. The Xtium2-CXP series takes full advantage of PCIe Gen 3.0 platform using PCIe x8 slots to deliver bandwidth up to 6.4GB/sec into the host memory while supporting image acquisition from up to 4 CXP12 input channels (12.5Gbps per channel). The Xtium2 CXP series is available in three configurations:
-
product
GPIB-ENET/1000 , Ethernet GPIB Instrument Control Device - United States 120VAC
781630-01
The GPIB‑ENET/1000 is an IEEE 488 controller device for computers with an Ethernet port. You can use this device to share a single GPIB system among many networked users or to control several test systems from a single networked host. The GPIB‑ENET/1000 features a password-protected web interface for easy configuration. It can also control IEEE 488 devices from anywhere on an Ethernet‑based (LAN) TCP/IP network (Gigabit, 100BASE‑TX, 10BASE‑T). Each device interfaces to and shares up to 14 GPIB devices from several network hosts, and you can control up to 100 GPIB‑ENET/1000 interfaces with a single computer. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
SAS (Serial Attached SCSI)
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
product
Pulse Acquisition Board
MS 1818
*Used to measure the amplitude of discrete pulses driving relay coils/motors*Programmable No. of samples acquisition with programmable trigger option*Converts sine wave to square wave for pulse measurement*Measures amplitude of sine wave*16 Bit ADC interface*16 Bit data bus host interface*FPGA based design with flexible configuration*1K FIFO Storage
-
product
8 Channel ADC for CompactPCI
CPCI393
The CPCI393 8-Channel Differential Input ADC card is very well suited to be used in applications in which autonomous signal conversion is an issue, as well as in standard mid-range applications. Enabled channels are scanned at maximum rate and conversion results are stored in shared memory. A local DSP performs the data acquisition and calibration transparent for the host.
-
product
MTM-USBStem: USB Microcontroller Module
CONTROL TEST ENVIRONMENTS through a wide-range of IO capabilities and enable communications between a host PC and any module on the BrainStem bus.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 400 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.828-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
1GS/s 75MHz BW USB Modular Scope Pen
USBscope50
USBscope50 marks a new era in ultra portable modular instrumentation for the PC or notebook. Using a USB1.1 or USB2.0 port on the host computer, USBscope50 offers the best of all worlds for converting your PC into a powerful diagnostic tool: tiny size, low power, low cost, modularity and high performance.
-
product
FPGA Image Processing (IP) Development Kit
ProcVision
Gidel’s Vision Pro Development Kit is an optimal solution for developing,validating, demonstrating and evaluating Image Processing (IP) andpipeline designs on FPGA.The suite is designed to provide a complete and convenient envelop enablingthe developer to focus strictly on the proprietary image processingdesign. The entire Vision Pro flow is within a single FPGA, independentof the final target application(s). The Vision Pro flow is composedof a pipeline that streams simulated data to the user image processingdesign under test (DUT) and then captures the design’s output streamfor displaying, storing, analysis and/or co-processing on host software.The entire process is performed on a single FPGA without the need foradditional peripheral connectivity or tools.Vision Pro suite is plug-and-play enabling the developer to begin at oncethe IP design development and validation. A simple design example providesthe developer immediate hands-on familiarization with the systemflow and supporting tools. The final design can be ported to any IntelFPGA device or other vendors’ devices (FPGA or ASIC) by replacing basiclibraries. To significantly reduce compilation time, initial design developmentmay be on a small FPGA device and later compiled for the targetdevice(s). The target implementation may use any FPGA board. For a fullImaging/Vision system solution, Gidel offers a number of off-the-shelfgrabbers and FPGA accelerators that are designed to utilize these imageprocessing blocks and Gidel Imaging Library (GIL).
-
product
RF Monitor Recertification
The use of RF personal monitors is widespread among wireless tower climbers and technicians. This is a relatively new development of the last five years or so. Prior to that, only a few monitors were in use. These were typically models developed for use by engineers, with a host of features not needed for routine climber protection. Consequently, they were expensive and not frequently used. As safety managers have begun to require all personnel working on wireless facilities to have personal monitors among their personal protective equipment, a new generation of cost effective equipment has emerged.
-
product
PCI Express Gen 1 Test Backplane
SKU-015-01
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
product
Non-contact Inline P/N Checker Module For Solar Wafer
PN-100BI
*Principle: Photovoltaic effect with the laser diode*Suitable for production line and tranceportation system*Connect to host PC by LAN to send measurement command and data
-
product
Product Development
Have a complex system level or product level solution you need to develop that could use some engineering know-how? Whether it is a sophisticated mission critical system or a product with your IP that needs a host, ARC can help you deliver on these complex solutions. Our DSX product, can help support your IP and be the host processor for your design, or if a larger system, DSX could be an integral part of your system.Don’t recreate the architecture. Let our team of experts help configure your product solution – by leveraging the best in FPGA and system level PXI technology that ARC has already created for you.
-
product
Radiation Microdosimeters
Teledyne e2v HiRel Microdosimeter is a compact hybrid microcircuit which directly measures total ionizing dose (TID) absorbed by an internal silicon test mass. The test mass simulates silicon die of integrated circuits on-board a host spacecraft in critical mission payloads and subsystems. By accurately measuring the energy absorbed from electrons, protons, and gamma rays, an estimate of the dose absorbed by other electronic devices on the same vehicle can be made. The Microdosimeter can operate from a wide range of input voltages. The accumulated dose is presented to three dc linear outputs and one pseudo-logarithmic output giving a dose resolution of 14 µrads and a measurement range up to 40 krads. These outputs are intended to be directly connected to most analog-to-digital converters (ADCs) or spacecraft housekeeping analog inputs (0-5 V range), which makes minimal demands on the host vehicle. The Microdosimeter incorporates a test function to allow electrical testing of the hybrid without the need for a radiation source.
-
product
Temperature Sensors
The infrared sensor measures temperature at a distance without contacting the target. The integrated infrared module senses the thermal radiation emitted by objects on a 16 x 4 array of sensing points, for measuring the temperature distribution across a surface. These 64 measurement pixels are transmitted via CAN to the host controller or data logging device. The sensor is available in both 35 and 60 field of view options to suit a variety of installations. A software package is provided for viewing live temperature data from the array.
