Control
Known value
-
product
Mini Receiver
FB7-NX
In about 1935, the National Radio Company of Malden, Mass., brought out a “hot” high frequency receiver, called the FB7, and the subsequent FB-7X. It featured a super-hetrodyne design with plug-in coils that gave it a broad frequency range. The “X” model also incorporated a crystal filter in the intermediate frequency section, thus giving it additional selectivity. The receiver was viewed by radio amateurs as a technological breakthrough, and it was also used commercially for point to point high frequency communications. As the receiver did not have an internal RF amplifier section, a separately tunable RF amplifier was later provided in a separate enclosure for additional performance capabilities. Now, National RF, Inc., is resurrecting the fabled receiver name with an all solid-state, hot mini receiver, which also utilizes plug-in coils to cover the HF spectrum. The mini-receiver is designed for use by radio amateurs as well as serious short-wave listeners, and allows reception of AM, CW, and SSB signals. It incorporates a super-hetrodyne design with a dual gate FET built-in RF preamplifier and a ceramic filter for selectivity, often required when used in a crowded amateur radio band. In addition, the receiver has a buffered rear panel output of the high frequency oscillator for use with either a frequency counter for exact receive frequency display, or for interface with an outboard transmitter. A rear panel jack is also provided for muting the receiver when a transmitter is placed into the transmit mode. And, the receiver is small enough to fit into carry-on luggage and taken on trips when it is desired to “keep an ear” on amateur radio or other high frequency activity. The receiver utilizes rear panel plug-in coil assemblies which contain the RF amplifier, mixer, and oscillator tuned circuits. Each plug-in coil assembly also comes with a separate dial scale, which is inserted onto the front panel for displaying the tuned frequency. A very smooth 6 to 1 planetary drive is used for tuning the receiver. Other front panel controls include RF preamplifier peak, volume control, Beat Frequency Oscillator adjustment, and RF gain control. Other switches include filter bandwidth, AM/CW/SSB selection, Power, and a general coverage/band spread control for certain plug-in assemblies. The receiver is intended to drive head-phones via a rear panel jack, but has sufficient output to drive a small external speaker.
-
product
Virtualized Front End Processor
quantumFEP
Kratos Defense & Security Solutions, Inc.
OpenSpace quantumFEP provides the digital processing and network connectivity needed between the Command & Control (C2) system and the RF Signal processing equipment. All of the digital processing functions in a typical satellite ground system are included - command and telemetry processing, recording, AES COMSEC security, CSSDS processing, packet-level FEC, and network gateway interface support.
-
product
Powered VXI Crates
VXI – (VME eXtension for Instrumentation): The demand for a compact, both flexible and fast industry-standard instrument-on-a-card architecture has driven the development of the VXI standard. The modular form factor, high bandwidth, and commercial success of the VMEbus made it particularly attractive as an instrumentation platform. The tremendous popularity of GPIB also made it attractive as a model for device communication and instrument control protocols.
-
product
Day/Night IP Surveillance Camera
ENVIROMUX-IPCAM-N
View and control the camera from the ENVIROMUX web interface, the camera web interface, included software, or with a compatible cell phone. With the ENVIROMUX-2D/5D/16D, a triggered snapshot can be forwarded in alert e-mails. A snapshot can be triggered by any programmed event (motion detection, door open/close, glass break, smoke, liquid detection, etc.). Image sensor: 1/4" progressive scan CMOS sensor. Video Streaming: simultaneous Motion JPEG and MPEG-4. Frame rate: 30fps at 640x480 (VGA) resolution. Lens: F2.0, 4.3 mm (0.17 in), 12 infrared LEDs for night vision. RJ45 connector. Wireless models: wireless IEEE 802.11 b/g up to 54 Mbps. Regulatory approvals: CE, FCC, RoHS.
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787456-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a … high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
PathWave BenchVue USB Modular DMM Pro
BV0021B
Connect and control your U2741A DMM to make measurements, plot graph and log unrestricted data with PathWave BenchVue USB digital multimeter software.
-
product
PXI Analog Output/Current Loop Simulator Module - 4 Channel
41-765-004
The 41/43-765-004 is an 4-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
-
product
10 MHz To 67 GHz LAN Wide Dynamic Range Average Power Sensor
L2057XA
Accurately measure any modulated signal with the Keysight Technologies, Inc. U/L2050/60 X-Series wide dynamic range power sensors. The USB/LAN connectivity models come with a wide dynamic range, covering -70 to +26 dBm. This sensor offers very accurate and repeatable power measurements for any modulated signal and comes with a super-fast measurement speed of 50,000 readings/sec, which enables higher manufacturing throughput. Users can also save time and reduce measurement uncertainty with the internal zero and calibration function. The U/L2050/60 X-Series is supported by the Keysight BenchVue software. BenchVue makes it easy to control your power meter to log data and visualize measurements in a wide array of display options without any programming. Simply connect the sensor to your PC installed BenchVue BV0007B Power Meter/Sensor Control and Analysis app to perform average power measurement and analysis.
-
product
6U VME Storage Module, 3 Drives, 5050 / 5051
5050
The 5050 is a 6U VME Storage Module with three 2.5” SSD in a single slot. Each SATA drive is accessible via front panel or RTM. Can be integrated into a multi-slot storage array using an external SATA RAID controller.
-
product
Fanless Embedded System With Intel® Core™ I7-6600U/i5-6300U/i3-6100U & Celeron® 3955U, 2 HDMI, 2 GbE LAN, 4 USB 3.0, 2 COM And PCI Express Mini Card Slot
eBOX560-500-FL
The eBOX560-500-FL is an Intel® Skylake-based fanless embedded system with compact size and full-featured I/O interface. To bring both excellent performance and ultra-low power consumption, the palm-sized embedded box PC is powered by the 6th generation Intel® Core™ i7-6600U or Celeron® 3955U processor (formally codename: Skylake). One 260-pin DDR4-2133 SO-DIMM socket with system memory up to 16 GB is available. The power efficient IP40 embedded system supports 12V DC input with screw-lock and features a user-friendly AT/ATX DIP switch. The compact eBOX560-500-FL is suitable for Industrial Internet of Things (IIoT) solutions, digital signage, retail equipment, smart factory automation, thin clients, industrial controller systems and many more.
-
product
4-Port RS232/4-port RS422
3101
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTS, with four ports using RS232 signal levels, and four ports using RS422 signal levels. The four RS232 ports each provide the full set of data and modem control lines configured for DTE
-
product
Safety Certified I/O Modules
HY-TTC 48XS
HY-TTC 48XS is an intelligent safety I/O module for extending the number of I/Os in mobile applications. The I/O module acts as a slave and is used in combination with, and controlled by a master electronic control unit and communicates via the standardized CANopen protocol, parameterized according to CiA DS 401. It is also compliant to the European Standard EN 50325-5 for CANopenSafety and is developed in accordance with the international standard EN ISO 13849 on functional safety, performance level (PL) d.
-
product
Data Analytics
KLA’s data analytics systems centralize and analyze the data produced by inspection, metrology and process systems. Using advanced data analysis, modeling and visualization capabilities, our comprehensive suite of data analytics products support applications such as run-time process control, defect excursion identification, wafer and reticle dispositioning, scanner and process corrections, and defect classification. By providing chip and wafer manufacturers with relevant root cause information, our data management and analysis systems accelerate yield learning rates and reduce production risk.
-
product
Single Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-101
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Motion Control Terminal Board For Mitsubishi J2S-A Servo Amplifiers
DIN-812M0
- On-board connector type: 100-pin SCSI-II female- Suitable for Mitsubishi J2 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8132
-
product
IOT Devices Testing
IoT devices refer to Internet of Things Devices. They are hardware devices programmed for specific applications and can transmit data over the internet and other networks. IoT devices include sensors, gadgets, actuators, gaming consoles, smartwatches, voice control devices, machines, vehicles, buildings, etc. collection and exchange of data.
-
product
High Power DC Electronic Load
36000A Series（50KW / 60KW）
36000A Series has its own control and display panel, CC / CR / CV / CP / Dynamic modes, 150 sets Store / Recall memory which provides load set-up more efficiently, also can be remote controlled via GPIB、RS232、USB and LAN interface.SHORT time setting and SHORT_VH, SHORT_VL setting function, also can measure Short Voltage and Current.
-
product
Flow Control Set Up Using PID Controller
ULP-25O & ULP-25T
Unitech Scales And Measurements Pvt. Ltd
Flow Control Setup Comprises of a Orifice with DPT to measure flow Rate. The flow of water is controlled by Control Valve with pneumatic actuator. I to P converter is provided to control the actuator. Rotameter is provided to measure actual flow rate. The system is mounted on a table top model with all necessary piping.
-
product
Power Supply, 30V, 50A, 1500W
N5765A
Keysight basic DC power supplies offer essential features for a tight budget. The Keysight 1500W, single output N5765A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current. It delivers solid performance and a variety of basic and enhanced capabilities in a compact 1U package.
-
product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 925Ω
50-297-021
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Structural Health Monitoring System
SHM
Automated stationary structural health monitoring system (SHM) is a subsystem of buildings and structures control system which has been developed in accordance with the applicable requirements of the corresponding standards. It is used to detect a transition of the building state from operational into the state of failure, that may eventually lead to fatal accidents.
-
product
Motor Drive Analyzer, 350 MHz, 8 Ch, 12 bits, 10 GS/s, 50 Mpts/Ch
MDA 8038HD
Static power analysis - like a dedicated power analyzer.Dynamic power analysis – capture more information.Complete test coverage – control system, power section, motor.Comprehensive mechanical interface.Harmonics calculation option.Vector display option (THREEPHASEVECTOR).Waveform Transformations option (THREEPHASEdq0).16 Channels with OscilloSYNC™.
-
product
Fiber Optic Multimeter
Combines the function of fiber optic power meter and fiber optic light source and the user can easily switch to choose the multi meter function via the control menu.
-
product
High Power DC Electronic Load
3350G Series（4KW~6KW）
Each 3350G Series module has its own control and display panel, CC / CR / CV / CP /Dynamic modes, also can be controlled via RS232、Ethernet、USB and GPIB interface.
-
product
(70×90×15mm) C-Band DWDM FGA Full Function Module Fixed Gain EDFA Module
FGA4400-FM02
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai FGA4400-FM02 series is a fixed gain Full Functional EDFA module which is specifically designed for C-Band DWDM optic transmission system, accord with various communication technology requirements of 44 channels DWDM system. It adopts nowadays excellent optical performance, advanced electronic control technology and complete software functionalities. Excellent total integration electronic transient control technology ensures amplifier to achieve the locking of optimal flat gain (OFG) in large dynamic input optical power range.
-
product
Video Test Hardware
The first integrated test equipment for testing DP Alt Mode in USB Type-C sinks and sources. UCD-340 features a flexible and robust way of testing video, audio and power delivery functions of USB‑C. The provided software enables user access to the vital parameters and controls needed when evaluating the various functions of the interface.
-
product
HDMI®, DisplayPort Video Test Solutions
We provide test instruments that help manufacturers bring next-generation video, audio, and control products to market – faster and without interoperability problems. The quantumdata series products support a variety of test solutions including functional testing for developers in R&D labs, compliance solutions for developers and test engineers, verification and diagnostic testing for professional A/V integrators and installers and fault testing on production lines in manufacturing facilities.
-
product
Linear Actuators MCS Controls
MCS
For those who need more than pushbutton control, Thomson offers a full line of MCS actuator control units. From simple to complex control, these units offer a variety of features with both DC and AC voltage outputs.
-
product
Coherent Modulation Transmitter
IQTX
Generating and controlling phase modulated optical signals is easy with the IQTX. The IQTX is referred to as a ‘Golden’ reference optical signal source because of its high repeatability and reliability.Its high bandwidth of 40 GHz ensures high quality optical signal generation, making it the ideal optical signal source for coherent communications applications.
-
product
Paper Moisture Meters
A paper moisture meter measures the humidity of paper and paper products. Use of a paper moisture meter can prevent costly damages resulting from paper expansion or shrinking. A paper moisture meter determines paper moisture content based on either absolute humidity or relative humidity. Absolute humidity does not take into consideration temperature, while relative humidity relies on temperature and is expressed as a percentage of the total amount of moisture possible at the current temperature. Thus, many paper moisture meter devices feature automatic temperature compensation (ATC).For paper producers, paper manufacturers, paper mills and others in the pulp and paper industry, moisture and humidity control is essential, especially during the production process, as excessive moisture can lead to warming of the paper rolls. A paper moisture meter can be used to detect moisture streaks during the paper production process as well as to identify optimal drying times.Regardless of whether paper is stored in paper rolls in paper converting plants or stacked in sheets and paper bales in commercial printing warehouses, the porous surface of paper gradually takes in moisture relative to the humidity of the surrounding environment. This moisture can be problematic, as too much moisture can cause curling, buckling or the formation of waves in otherwise flat paper products. Moisture also can prevent inks, dyes, paints and coatings from covering and saturating paper properly during printing and processing.PCE Instruments (PCE) offers digital handheld moisture meter devices for measuring the moisture content of paper and paper products such as cardboard, paperboard, corrugated boxes, craft paper, wrapping paper, brown packaging paper, butcher paper, recycled paper, coated paper and more. Different paper moisture meter models utilize different paper moisture measuring techniques, performing moisture content tests of paper products via either destructive or nondestructive methods. Typically, a standard pinless paper moisture meter is nonpenetrating, thus allowing for the nondestructive measurement of paper water content.
