Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Conditioners and Transmitters
-
DIN rail mounted micro-controller based analogue load cell transmitters. They have very high accuracy and long term stability with advanced design.Using an up to-date delta-sigma ADC and 16 bit DAC to achieve higher speed and accuracy these instruments give the system designers a lot of advantages towards increasing system reliability and reducing the installation and service times. All instruments' analogue outputs are matched during production to simplify calibration with a PLC and to simplify exchanging the instrument without recalibration in service when initial adjustment has been performed in the PLC.
-
Product
Modular Test System
-
A modular test system, RTS (real time scanner) provides instant test results with minimal interface cables to check wiring during installation.It tests wire harnesses in real time using our micro switching technology, reducing the need for high cost interface cables by around 90%. an innovative best-in-class solution for FAL testing, RTS also offers many benefits for wire harness and sub-assembly manufacturers.
-
Product
Electrical Tomography
POLARES32
-
By exploiting an innovative technology based on the use of Alternating Current (AC), the POLARES32 Electrical Tomography can measure and display all the survey parameters at the same time: ground resistivity values, current, voltage, spontaneous potential, induced polarization and indication the quality of the measurement.
-
Product
ENA Vector Network Analyzers
-
Create accurate, dependable test stations with high throughput, repeatability and reliability Streamline your measurement flow with intuitive user interface and achieve better results in less time Secure your assets with upgradability, including software and hardware such as frequency and test port
-
Product
Bus Analyzer / Exerciser
PCF850
-
The PCF850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
Product
Full Wave Recorder
I-FullWaver
-
The I-FullWaver systems were specifically developed for precise full waveform time domain induced polarisation, Resistivity and self-potential measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
Product
Digital Melting Point Apparatus
DRK8011
-
Shandong Drick Instruments Co., Ltd.
DRK8011 Digital melting point apparatus is fully in line with ‘humanize’ of the design concept, using photoelectric automatic detection, dot matrix image LCD technology, digital keyboard input, each measuring one sample, measure three times the average of the melting point of the automatic strike, and has a melting, melting end automatically, melting curve automatic recording function. Temperature system uses high inearity make platinum resistance sensing element, the use of PID regulationtechnology to improve theaccuracy and reliability of the melting point, and with integrated electronic circuits to achieve rapid "starting temperature" setting and eight stalls to choose from linear "heating rate" Automatic Control. Instrument to establish communication with the PC via USB, save or print the graph, the instrument can be directly connected with the RS232 mini-printers, print graphs. The instrument uses Pharmacopoeia as a sample capillary tube.
-
Product
Bore Gauge
BG10
-
Aeronautical & General Instruments Ltd.
The BG10 Gun Barrel Bore Gauge System is an electro-mechanical measuring device that was originally introduced into service by the RAF for the high-speed measurement of aircraft cannons, to ensure minimum operational aircraft turnaround time. Measurements are taken at 16 pre-determined positions along each bore, which are then compared to pre-stored warning and rejection criteria. The actual measurements taken are displayed to the Operator on an LCD display and the measurements stored for future reference. The system will automatically provide a visual indication on the Hand Held Unit whether the barrel was acceptable, close to tolerance or rejected – all this to be undertaken in less than five minutes!
-
Product
Mechanical Testing
-
Mechanical testing typically includes measurements of the physical properties of materials. These properties include strength, stress, stiffness, hardness, toughness, resilience, load-through-time or fatigue.
-
Product
Pulse Heat Unit (Hot Bar Bonder)
-
*This method is most suitable for reliable soldering and thermo-compression because heating and cooling are done applying the pressure force*Good repeatability of heating temperature and time requires no skilled workers*Partial heating in short time allows to reduce thermal damages*For implement of Pb free
-
Product
SparkFun Distance Sensor Breakout
4 Meter, VL53L1X (Qwiic)
-
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 40mm to 4m away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
Product
Kafka Monitoring With RTView®
-
RTView Enterprise provides turnkey Kafka monitoring with pre-built dashboards. With over 30 pre-defined alerts and over 15 pre-built monitoring dashboards, users can deploy quickly without the time, skill and expense necessary to build or configure their own monitoring applications or dashboards.
-
Product
Temperature & Process Calibrators
-
The most sophisticated industrial equipment will not be useful unless it is calibrated. GAOTek Process Calibrators are used to adjust instruments’ accuracy, and they are the only process calibrator you will ever need to carry. They can measure temperature, pressure, voltage, resistance and frequency, and can be used during troubleshooting. Through calibration, you can ensure that any equipment performs as expected and that it can be relied on to deliver predictable and accurate results that meet quality standards. GAOTek Process Calibrators come with a USB interface which makes it easier to transfer the results to other devices which otherwise would have taken a long time to transcribe them. Our Process Calibrators are for sale to the United States, Canada and globally.
-
Product
Automatic Vision Measuring Machine
-
Sinowon Innovation Metrology Manufacture Ltd.
Moving bridge structure, measured workpiece is fixed;◆ Four-axis CNC fully auto close loop control, auto measurement;◆ “00” grade “JINANQING”marble base and pillar, stable and reliable;◆ Imported open type linear scale, resolution is 0.1um, high accuracy, great stability;◆ Imported P grade linear guide, precision grinding ball screw and AC servo motor, ensure accuracy stability of system position;◆ Imported high definition color industry camera, ensure clear observation and stable measurement requirement;◆ 6.5X continue auto zoom lens, precision auto zoom, only need to make pixel calibration once time;◆ Programmable 5-ring 8-division LED surface illumination, contour parallel LED illumination, can realize 256 grade brightness adjustment intelligently;◆ Equipped with imported touch probe, realize 3D measurement;◆ With proprietary fully auto measuring software iMeasuring 4.2, powerful function, simple operation;◆ Optional laser probe, it can also be customized according to customer request;◆ Optional FexQMS Measuring Data Analysis and Real-time monitoring software which enhance program control and reduce material
-
Product
Fibre Network Providers for High Speed and Low Latency Network Infrastructure
-
PBE Group is a fibre network provider that delivers a vast array of integrated tunnelling and mining projects globally and offers custom fiber-based solutions that are reliable, robust and easy to use.Rebroadcasting systems (LTE, FM, TETRA, P25, etc), video monitoring and real time machine control systems can demand high bandwidth and low latency for operation. PBE offers a wide range of fiber-based solutions that can satisfy these requirements. PBE provides Ethernet over Fiber Network and RF over Fiber Network systems in mines and tunnels.Fiber network has a number of advantages:- Covers greater distances with less loss- Support high bandwidth- Immunity to EMI and RF Interference- Support different topologies (Star, Ring, Tree, etc.)- Flexible design and deployment- Flat frequency response and wide frequency ranges- Easy to implement redundant network
-
Product
Battery Extra Load Units
-
Performing capacity/discharge test on a high-capacity battery may be challenging since high requirements are set on the discharge system. In cases when discharge test times need to be reduced, high load capacities are required from the discharge system. The battery extra load unit BXL is an additional load unit designed especially for this purpose.It is primarily used with BLU battery testers. However, the unit is a universal add-on device. This means it can be used as an additional load with any other discharge/capacity tester in the market.When discharge current exceeds the capacity of a single BLU device, extra load unit increases discharge capacity. A system of BLU and BXL instruments enables performing the capacity test in an accurate, user-friendly way in accordance to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.
-
Product
Wafer & Die Inspection
-
SemiProbe wafer inspection system (WIS) examines, locates and identifies defects created during wafer manufacturing, probing, bumping, dicing or general handling. This provides microelectronic device manufacturers with accurate, timely quality assurance and process information. The WIS has single sided and double sided wafer mapping capabilities and can improve efficiency, reduce manufacturing costs, increase yields and shorten time to market.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX4032A
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
GeoSwath Module
-
The GeoSwath Plus Sonar Module contains a wide-swath bathymetric sonar suitable for a range of survey and inspection tasks. The GeoSwath Plus is a 500kHz interferometric sonar, or phase detecting bathymetric sonar (PDBS) from Kongsberg GeoAcoustics. Boat-mounted GeoSwath sonars are used worldwide for high accuracy surveys including port and harbour navigation and environmental mapping: the Gavia’s GeoSwath module makes this capability available in a commercial AUV. The GeoSwath Plus offers: wide swath coverage of up to 12 times the AUV altitude when near the seabed; integrated bathymetry with simultaneous true digital side scan; high depth resolution suitable for IHO survey standards; as well as the accuracy and repeatability of a boat-mount hydrographic survey system. Like most of the survey-grade sensors on the Gavia AUV, the GeoSwath data is time-synchronised with the AUV master clock using the vehicle PPS/ZDA system. Benefits of the GeoSwath AUV module include ease of deployment, ease of use, reducing survey time, and the ability to take a 500kHz high-resolution sonar down to targets in 1000m of water. The GeoSwath Plus post-processing software (provided as standard with the system) allows a user to inspect and process the data, create and inspect digital terrain models, and create basic sonar mosaics. Several other commercial post-processing software packages are also available, please ask for details. Note that for best results the GeoSwath Module should be deployed with a direct-reading sound velocity sensor (option) in the Control Module, and one of the high-accuracy INS/DVL Navigation Modules for motion sensing.
-
Product
1 GHz 4 Analog Channels Oscilloscope
DSOX3104A
Oscilloscope
1 GHz4 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
PC based USB Real Time Analyzer
-
1) Measurement microphone and its accessories (a windshield and a microphone clip)2) XLR-to-USB Converter3) USB cable (1.5 m) 4) CD (contains the copy-protected Multi-Instrument Software) 5) USB hardkey (contains a Multi-Instrument Standard License)6) Audio Test CD (contains a list of audio test tones and noises) (AudioTestCD.zip or AudioTestCD.rar)7) 1/8” TRS cable (1.8m) 8) Black Soft Pouch Case 9) Individual Sound Level Calibration Data 10) Individual Microphone Calibration Data (only provided in RTA-168B)11) A small microphone stand
-
Product
Software Module for Fast, Easy CMM Programming and Automation
Verisurf Automate
-
Verisurf AUTOMATE is CMM programming software developed from the ground up to provide a modern user experience that reduces both programming time and cycle run time. AUTOMATE requires significantly less training and experience for quality departments to immediately benefit from higher productivity.Verisurf AUTOMATE is an intelligent, object oriented programming application with an inherently intuitive and visual workflow that simplifies the most complex CMM programming.
-
Product
Data Recorder and Playback System
-
Curtiss-Wright Defense Solutions
The proliferation of sensors in today’s Intelligence, Surveillance and Reconnaissance (ISR) applications has increased the need for recording and playing back multiple channels of high-speed sensor data. Often times these ISR platforms are airborne which present certain environmental requirements that must be met for the system to be flight ready.
-
Product
Countdown Or Countup Clock Controller
RC600
-
The RC600 is a remote control that adds both countdown and countup timer control features to our NTDS and TCDS clocks. Reference or generate time input from NTP or time code (IRIG & SMPTE). Control a virtually unlimited number of time code clocks and network clocks.
-
Product
Ball Probe Moisture Meter with Bluetooth®
FLIR MR59
-
The FLIR MR59 is a pinless meter with wireless connectivity, which offers the convenience to view live readings from a mobile device via the FLIR Tools® Mobile app. Thanks to the ball-shaped sensor, users can cover a large area in a short time without making a mark; measure into corners and around baseboards easily; and detect problems below the surface.
-
Product
Vehicle Multiprotocol Interface Device
Interface
The Vehicle Multiprotocol Interface Device excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
Advanced In-Kiln Moisture Measurement System
MC4000
-
The MC4000 Advanced In-Kiln Moisture Measurement System enables the kiln operator to monitor the moisture content of each charge and develop consistent drying time schedules for improved kiln performance and reduced operating costs. The MC4000 will cut costs due to degrade and overdrying and improve grade recovery to help increase the bottom line.
-
Product
18-Slot 3U PXI Express Chassis with AC - Up to 8 GB/s
PXES-2780
Chassis
The ADLINK PXES-2780 is an 18-slot PXI Express chassis, compliant with PXI Express and cPCI Express specifications and offering one system slot, one system timing slot, ten hybrid peripheral slots, and six PXI Express peripheral slots for a wide variety of testing and measurement applications requiring enhanced bandwidth. The PXES-2780 provides a configurable PCIe switch fabric and is configurable in two-link, and four-link PXI express deployments, with 8 GB/s system bandwidth and up to 4 GB/s slot bandwidth for dedicated peripheral slots, thanks to PCIe gen2 signaling technology.
-
Product
Mixed Signal Oscilloscope - 350 MHz, 4 Analog Plus 16 Digital Channels
MSOX4034A
Oscilloscope
350 MHz4 analog plus 16 digital channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
Environmental Radiation Monitoring Systems
-
With the autonomous radiation monitoring probe GammaTRACER, the gamma radiation dose is continually registered in the chosen time sequence. Energy-saving chip technology allows maintenance-free non-stop operation of the GammaTRACER probe of typically five years, with extended battery pack up to ten years! Hermetically sealed, it is designed to endure the harshest environments.
